The society strives for sustainable development, in the construction industry it is expressed through sustainable building. Energy and LCC analyzes increases the ability to make conscious decisions in the process. A problem in the construction industry is that energy and LCC analysis is not used to the desired extent, as they are perceived as complicated and time consuming. The report aims to achieve a more sustainable building through increased use of energy and LCC analyzes.The goal is to show how BIM can be used to improve the efficiency of the energy and LCC analyzes.The study was conducted with a literature review and a case study to answer which information that is required in a BIM model to perform energy and LCC analyzes. The study also shows which software can be used in BIM based energy and LCC analyzes and how the analyzes can be carried out efficiently.The result shows that effective analyzes may be performed if the BIM-model contains the relevant information for making analyzes.

Sweden has an environmental goal to achieve until the year 2020. To achieve this goal the construction business has to take an initiative to use the modern techniques that are available to lower the energy consumption I buildings. There?s also a debate going on today regarding the energy demands set by the Swedish government through Boverket, some communities throughout Sweden thinks that the demands are to low and have therefore set up own demands regarding energy in buildings.The possibility to construct energy-saving buildings is today very great, with energy-efficient heating-systems and dense climate envelope. The interest to raise energy-efficient buildings have also increased as a consequence that the population have become more aware about their impact on the environment.

sustainable development by reducing the energy use by EU:s directive of energy efficiency and the UN Convention. The second purpose is to present the technical solutions regarding ventilation and heating system that is being used in passive houses. This was done using 8 passive houses, 4 germany and 4 swedish passive houses. Even the international and Swedish system requirements for passive houses have been addressed in this project. The goal was also to explain how and why the mechanical system in passive houses has developed to the technology used today.

Tumble dryers and drying cabinets have to a large extent replaced the traditional way of drying clothes outdoors. They are faster, more convenient, require less space and can be operated regardless of weather conditions. This replacement has significantly increased residential energy consumption, due to the fact that tumbles dryers consume large amounts of electrical energy. In the USA 9 % of the households electric energy is consumed when drying clothes. Over 4 million tumble dryers are sold in Europe each year and 20 % of the residential electricity consumption in Sweden is used drying and washing clothes.

The number of data centers and their capacity is increasing throughout the world. Theenergy used in these data centers and the emissions from the use are increasing at thesame rate. The total use of energy will double from 2008 to 2011 based on the trends indata centers use. Research in this area says that the emissions from data centers willhave surpassed the level of airline traffic in 2020. The index used today to compare howefficient a data center is, called PUE, is lacking some information.

More efficient energy consumption is essential to secure a sustainable future, not least within the building and real estate sector which answers for approximately 40 % of the EU countries total energy consumption. One part of EU: s work to reduce the energy consumption is the directive on energy performance of buildings which among other things have lead to stricter demands on energy performance in new and renovated buildings.One of the difficulties with making buildings more energy effective is that it often demands big investments and although it results in lower operating costs the extent of these savings and therefore also the repayment time can be difficult to decide beforehand. To make it interesting for property owners and also tenants to invest in energy efficient buildings powerful incentives are needed. Favorable loans to energy efficiency projects are one example of governmental instruments that have been tested in other European countries with good results.Reduced operating costs appear to be the main incentive for property owners to make their buildings more energy efficient. The best result of an energy efficiency project is usually achieved by cooperation between property owners and tenants but in order to make that interesting it is important that both parts can profit from the savings.

The objective of this work was to evaluate and implement a number of energy saving functions for a specific embedded system. The functions were then grouped into a number of energy levels with known properties in terms of functionality, energy consumption, and transition time between the levels.The embedded system consisted of an AT91 ARM9 processor, GSM/GPRS modem, display, Ethernet and other peripheral units. Some energy saving methods that were considered were suspend to RAM, suspend to disk, frequency scaling, and methods for saving energy in the modem, Ethernet, USB and display backlight. The functions were grouped into levels and an interface was specified for controlling the energy level.It proved possible to get known properties within the defined energy levels, even though the paritioning of functions into these levels proved to be sub-optimal in a typical application usage scenario because it was designed for mainly energy consumption, not usage.The final result is a number of energy saving functions grouped into levels, which are controllable via an application interface. Each of the levels have a known energy consumption in both loaded and un-loaded mode..

The objective of this work was to evaluate and implement a number of energy saving functions for a specific embedded system. The functions were then grouped into a number of energy levels with known properties in terms of functionality, energy consumption, and transition time between the levels.The embedded system consisted of an AT91 ARM9 processor, GSM/GPRS modem, display, Ethernet and other peripheral units. Some energy saving methods that were considered were suspend to RAM, suspend to disk, frequency scaling, and methods for saving energy in the modem, Ethernet, USB and display backlight. The functions were grouped into levels and an interface was specified for controlling the energy level.It proved possible to get known properties within the defined energy levels, even though the paritioning of functions into these levels proved to be sub-optimal in a typical application usage scenario because it was designed for mainly energy consumption, not usage.The final result is a number of energy saving functions grouped into levels, which are controllable via an application interface. Each of the levels have a known energy consumption in both loaded and un-loaded mode..

Former studies have shown that a considerable part of industries? energy usage can stem from idle times in the production. This thesis, carried out at Siemens Industry sector, evaluates the potential for using the control system to automatically put machines into energy saving mode during idle times. The main part of the thesis consists of a case study performed on machine tools at a Scania production site in Södertälje. Through load measurements the potential for energy savings was determined.The results show that there is a great potential for energy savings during idle times at the site.

How to use automatically read data to create a method that visually describes how energy is used in a building, the so called energy signature..

Solar energy is the one most talked about among energy sources due to its huge potential amongst renewable energy technologies. A greater use of the solar energy may be the solution to today's climate threats. Normally there are two different types of solar technologies, solar cells and solar thermal collectors. Solar cells convert solar energy in to electricity whilst solar thermal collectors convert solar energy into heat, which can be used to heat hot water for households. This goal of this study has been to investigate the possibility of implementing solar energy into the energy system of Kista Galleria, one of Sweden's foremost venues.

The objective of this work was to evaluate and implement a number of energy saving functions for a specific embedded system. The functions were then grouped into a number of energy levels with known properties in terms of functionality, energy consumption, and transition time between the levels.The embedded system consisted of an AT91 ARM9 processor, GSM/GPRS modem, display, Ethernet and other peripheral units. Some energy saving methods that were considered were suspend to RAM, suspend to disk, frequency scaling, and methods for saving energy in the modem, Ethernet, USB and display backlight. The functions were grouped into levels and an interface was specified for controlling the energy level.It proved possible to get known properties within the defined energy levels, even though the paritioning of functions into these levels proved to be sub-optimal in a typical application usage scenario because it was designed for mainly energy consumption, not usage.The final result is a number of energy saving functions grouped into levels, which are controllable via an application interface. Each of the levels have a known energy consumption in both loaded and un-loaded mode..

The society strives for sustainable development, in the construction industry it is expressed through sustainable building. Energy and LCC analyzes increases the ability to make conscious decisions in the process. A problem in the construction industry is that energy and LCC analysis is not used to the desired extent, as they are perceived as complicated and time consuming. The report aims to achieve a more sustainable building through increased use of energy and LCC analyzes.The goal is to show how BIM can be used to improve the efficiency of the energy and LCC analyzes.The study was conducted with a literature review and a case study to answer which information that is required in a BIM model to perform energy and LCC analyzes. The study also shows which software can be used in BIM based energy and LCC analyzes and how the analyzes can be carried out efficiently.The result shows that effective analyzes may be performed if the BIM-model contains the relevant information for making analyzes.

The housing sector uses 40 % of the energy in Sweden and half of the electricity usage. Theuse of energy is the main reason to the increasing rate of carbon dioxide in the atmosphere.This is the main motive but also a wish of higher safety, that is a higher rate of selfsufficientenergy production in Sweden, we want to decrease the need of using fossil fuel. Now whenthe energy price rise, the interest in energy issues increase and more people discuss thepossibility of reducing the usage of fossil fuel. A change to renewable energy such as sun,wind and water is the only solution where we can get a sustainable development.One way to contribute to a better use of energy is to build in the principle of passive house.The house is being built with a thick and tight insulation. If you use a heat-exchanger withhigh degree of efficiency and a final heating battery on the ventilation system, the heat fromlamps, devices and the ones living in the house should be enough to fulfil the criteria ofliving.

Calculated and measured energy in residential buildings is going to differ. The reason to this may be due to many factors. In this study there is a study on how these factors affect the energy use in a building. To get an insight in what defines energy, there is first a description of energy supply both worldwide and used in Sweden, followed by a description of the energy balance. In this study energy will be studied in residential buildings only.