In order to reach the environmental targets, set up by the EU, there are many measures taken to make Sweden more energy efficient. In the housing and real estate sector, an installation of an exhaust air heat pump that reuses the heat in the exhaust air in order to lower the amount of acquired energy, is an example of such an action. The recovered energy can then be used for heating of radiators and tap water. This report aims to evaluate and compare three different systems using exhaust air heat pumps regarding COP, degree of coverage and cost savings. This study was delimited to only account for apartment buildings.The theory chapter describes the different conditions and factors that affect a building?s energy balance.

På uppdrag av Sweco Systems i Umeå har detta examensarbete utförts under våren 2013. Syftet var att undersöka huruvida något av de energiberäknings-program som används på företaget kan anses vara lämpligt vid energikartläggningar av befintliga fastigheter.Inledningsvis utfördes en energikartläggning av fastigheten Odin 12 i Umeå, som i huvudsak utgörs av gallerian MVG. Med resultaten från denna energikartläggning som grund beräknades därefter fastighetens energianvändning i två olika program ? VIP-Energy och IDA Indoor Climate and Energy.Resultaten från den inledande kartläggningen visar att fastigheten har ett lågt behov av fjärrvärme, vilket förklaras av fastighetens höga elförbrukning. Den stora användningen av el genererar stora mängder internvärme som, förutom att sänka fjärrvärmebehovet, även medför att fastigheten under hela året har ett kylbehov.Utvärderingen av de två beräkningsprogrammen visar att VIP-Energy är ett lämpligt program att använda vid energikartläggningar.

The objective of this work was to evaluate and implement a number of energy saving functions for a specific embedded system. The functions were then grouped into a number of energy levels with known properties in terms of functionality, energy consumption, and transition time between the levels.The embedded system consisted of an AT91 ARM9 processor, GSM/GPRS modem, display, Ethernet and other peripheral units. Some energy saving methods that were considered were suspend to RAM, suspend to disk, frequency scaling, and methods for saving energy in the modem, Ethernet, USB and display backlight. The functions were grouped into levels and an interface was specified for controlling the energy level.It proved possible to get known properties within the defined energy levels, even though the paritioning of functions into these levels proved to be sub-optimal in a typical application usage scenario because it was designed for mainly energy consumption, not usage.The final result is a number of energy saving functions grouped into levels, which are controllable via an application interface. Each of the levels have a known energy consumption in both loaded and un-loaded mode..

The biogas plant Kungsängens gård, owned by Uppsala Vatten och Avfall AB, produces biogas and biomanure from organic household waste, food processing waste and slaughterhouse waste. In year 2012, 4.4 million Nm3 of biogas were produced from 25 200 tons of waste. Before digestion all substrate is sanitized by one hour?s pasteurization at 70°C in order to kill pathogens. Another method, integrated thermophilic sanitation (ITS), is of interest in order to decrease the energy demand.

Mechanical ventilation is the most common type ofventilation in newly constructed office buildings. Therehas been an interest to utilize natural ventilationinstead of mechanical ventilation among architects andHVAC consultants in recent years. This is due to thesize of mechanical ventilation systems, which arespace consuming. The mechanical ventilation system isalso complex and requires maintenance. Furthermore,the fan uses a considerable amount of energy.

As the Swedish governments long term goals include a reduction of fossil fuel dependency, increasing pressure is placed upon energy companies to create and develop new solutions for renewable energy. The following case study was done in collaboration with the company Sydved Energileveranser AB and one of their contractors, Enarssons Skogsentreprenad AB. The objective of the study is to examine the bioenergy situation in region of Skåne and evaluate the potential solutions in the region for a forest-fuel assortment, based on a bioenergy-cutting-system. As a part of this study I have compared ordinary manual cuttings done with a chain saw and cuttings made using the new ?bio- energy cutting system?. The cuttings made under both systems were tested in areas near agricultural fields or pasture land in order to maintain an open landscape.

The objective of this work was to evaluate and implement a number of energy saving functions for a specific embedded system. The functions were then grouped into a number of energy levels with known properties in terms of functionality, energy consumption, and transition time between the levels.The embedded system consisted of an AT91 ARM9 processor, GSM/GPRS modem, display, Ethernet and other peripheral units. Some energy saving methods that were considered were suspend to RAM, suspend to disk, frequency scaling, and methods for saving energy in the modem, Ethernet, USB and display backlight. The functions were grouped into levels and an interface was specified for controlling the energy level.It proved possible to get known properties within the defined energy levels, even though the paritioning of functions into these levels proved to be sub-optimal in a typical application usage scenario because it was designed for mainly energy consumption, not usage.The final result is a number of energy saving functions grouped into levels, which are controllable via an application interface. Each of the levels have a known energy consumption in both loaded and un-loaded mode..

How to use automatically read data to create a method that visually describes how energy is used in a building, the so called energy signature..

Solar energy is the one most talked about among energy sources due to its huge potential amongst renewable energy technologies. A greater use of the solar energy may be the solution to today's climate threats. Normally there are two different types of solar technologies, solar cells and solar thermal collectors. Solar cells convert solar energy in to electricity whilst solar thermal collectors convert solar energy into heat, which can be used to heat hot water for households. This goal of this study has been to investigate the possibility of implementing solar energy into the energy system of Kista Galleria, one of Sweden's foremost venues.

The objective of this work was to evaluate and implement a number of energy saving functions for a specific embedded system. The functions were then grouped into a number of energy levels with known properties in terms of functionality, energy consumption, and transition time between the levels.The embedded system consisted of an AT91 ARM9 processor, GSM/GPRS modem, display, Ethernet and other peripheral units. Some energy saving methods that were considered were suspend to RAM, suspend to disk, frequency scaling, and methods for saving energy in the modem, Ethernet, USB and display backlight. The functions were grouped into levels and an interface was specified for controlling the energy level.It proved possible to get known properties within the defined energy levels, even though the paritioning of functions into these levels proved to be sub-optimal in a typical application usage scenario because it was designed for mainly energy consumption, not usage.The final result is a number of energy saving functions grouped into levels, which are controllable via an application interface. Each of the levels have a known energy consumption in both loaded and un-loaded mode..

A large amount of our time is spent indoors in an artificial climate. To make the experience pleasant there are requirements on the ventilation and the heating system. At the present time the most common form of heating is a radiator system complemented with a ventilation system. A ceiling heating system with combined heating and ventilation can replace the two separated systems. The benefit with a ceiling heating solution is that it saves space since the radiator system is no longer needed.

This master thesis is an in-depth study of an existing heating system at a household cooperative in Uppsala that has been converted from district heating to a bedrock heat pump system. The study focuses on an economical system optimisation of the building?s complete heating system. The aim was to determine how well a heat pump system in large buildings actually work, find out possible ways to optimize the existing system and point out important system parameters for new heat pump installations in larger buildings.The project points out a possible energy cost reduction of 45 % without investment and further cost reductions with equipment investments. A reduction by 30 % is possible by improvements in the regulation system and 15 % is possible by maintaining the brine system.

Ocean Thermal Energy Conversion, OTEC, is a sustainable energy conversion technology that is not yet commercialized. OTEC is a technology that utilizes the temperature difference in oceans between the warm surface water and the cold water at 1 000 m depth to run a Rankine Cycle. This technology can produce electricity and provide synergies like fresh water, air conditioning and aquaculture. A simulation program for three alternative OTEC systems has been created in order to decide which OTEC system is most profitable; closed, open or hybrid system. In this simulation a production cost analysis is performed in order to investigate and decide which one of the three systems that has the lowest production cost. The production cost analysis also analyzes if the profitability is affected by the size of the facility. After these analyzes, the most profitable of the three different OTEC-systems is expanded by an installation of solar collectors in order to see if the thermal efficiency is improved. The result shows that the most profitable system varies with the size of the facility.

Sweden is a country that has made some progress in developing energy efficient solutions. The problem in Sweden is that many houses and apartment buildings are old and have inefficient ventilation- and heating systems. This energy is lost when systems are inefficient, which then results in huge economic costs. Luckily, more and more people are becoming aware of this, which means that Sweden is on track to become even better within energy efficiency.Energy use for the housing- and service sector amounts to 166 TWh of total use at 616 TWh. Without distribution and conversion losses, these figures show that the housing- and service sector accounts for almost 40 % of the country's total energy consumption.

The Energy Performance Certification in Sweden was developed as a tool to achieve the Government's target to reduce Sweden's energy consumption by 20 percent by 2020. The Energy Performance Certificate has previously received some criticism for not fulfilling its purpose. Questions that formed the basis for this report is how the energy performance certification provides support to buyers of single-family houses and if the energy performance improved in terms of reliability. The report begins with a background description that describes how the energy declaration works and some of the findings of previous evaluations and surveys. A survey to investigate the broker's position to energy performance have been conducted as well as interviews with buyers and sellers of houses. An investigation whether the energy performance can vary between different calculation programs, depending on various assumptions made by the energy declarant, has been made.Brokers and sellers have proved negative attitudes towards energy performance, particularly brokers.