This master thesis describes the development of an UPS module. UPS is an acronym for Uninterruptable Power Supply. The UPS module has been developed at the company AerotechTelub AB. The UPS module delivers the necessary voltage and current in case of a power interrupt. If a power interrupt occur, the computer system has one to three minutes available to store data and shut down correctly.

This bachelor thesis describes the process of developing a two wheeled robot with activebalancing. The robot is designed to go straight ahead until it reaches a finish line. Then it shallstop to stand still balancing. The workload in the group has been divided according to theprevious individual projects, which are attached. The design of the robot is inspired by theconcept of the Segway.

This master thesis work was done at Saab Underwater Systems AB, a company at the cutting edge of underwater technology. Here torpedoes and other underwater vehicles are developed and manufactured. The major customers are navies of different countries, mostly the Swedish navy. The aim of this master thesis is to develop, construct and evaluate an automatic Trim System for Unmanned Underwater Vehicles. The task of the system is to change the position of the centre of mass and the vehicle?s total mass or volume.

Detta examensarbete syftar till att implementera en modulgenerator som automatiskt genererar ett matchat differentialpar. Detta för att enkelt kunna generera detta vanlig förekommande byggblock utan att behöva rita om allt från grunden. Modulgeneratorn som konstruerats klarar att skapa upp till 2x2 transistor block matchad layout med eller utan sköld. Programmet skapar med hjälp av indata från konstruktören en skräddarsydd layout som kan användas som byggblock i integrerade kretsar. Examensarbetet är slutfört och har genomgått omfattande testning The aim of this thesis is to implement a module generator that automatically generates a matched differential pair.

This thesis work contains a litterature study about electrical motors in general and how PWM-patterns for brushless DC-motors can be made. A suitable method has been implemented as a simulation model in VHDL. A simulation model of a brushless DC-motor which describes the phasecurrents, torque and angular velocity has also been made. The motor model made simulations easier for the complete PWM-system. The design was synthesised and tested with a prototypeboard including a SPARTAN II FPGA.

Anledningarna till att använda sig av en trådlös signalöverföring i en industri kan vara många, oftast handlar det om ställen där det är svårt eller omöjligt att ha en trådad förbindelse. I det här fallet är det en sedimenteringsbassäng där man tar hand om processvatten från industrin. Bassängen är utformad som en cylinder där vattnet rinner genom olika avdelningar för att minska innehållet av sediment. I bassängen cirkulerar en plattform med diverse omrörare och skrapor på. Eftersom denna del går runt hela tiden är det svårt att ha en fast förbindelse till de drifter som finns.

This thesis aims to develop proposals and models for a modular Electronics construction to a future D250S Dual battery charger. The aim also includes investigation of possibilities to use some of Texas Instruments C2000 microprocessors. The reason for this is that CTEK SWEDEN AB wants to renew the present D250S Dual battery charger and lower the manufacturing costs. The thesis work has involved gathering theoretical facts for the development of a design on the modular electronic construction, the choice on which microprocessor to use, the choice of electronic components and facts about peripheral equipment to the D250S Dual. With the theoretical there has been developed different solutions to the proposed hardware and software solutions with comparisons in aspects of positive and negative.

GNT Group is a Nordic/Baltic wholesaler that distributes products in the IT, entertainment and home Electronics sector. GNT is facing problems with inaccurate inventory levels which can lead to unnecessarily high inventory carrying costs or lost sales. Currently the decisions about when and how many to order are made somewhat arbitrarily by the responsible personnel. Their decisions are based only on some brief sales history and on experience. GNT wants to develop its ERP system to be able to support the purchaser in these and other related decisions.

This Master's Thesis describes the design of a new system where a digital signal processor has been added to an existing imaging system consisting of field programmable gate arrays. The new system will offer a higher degree of flexibility by considerably shortening the design time and make it possible to implement more complex algorithms than the existing ones. The choice of system architecture and a test implementation are discussed. The test implementation consists of a program for the digital signal processor and VHDL code for one of the field programmable gate arrays. The code for the digital signal processor was designed for testing on an evaluation board from Texas Instruments.

Att ett grafikkort ska behandla data och sen generera en bild på en skärm är en ganska logisk funktion för ett grafikkort. Vad som har gjorts här är att alla grundläggande funktioner för grafikkortet har tagits bort, detta för att ingen behandling ska göras. Detta har gjorts för att kunna låta data passera genom kortet med så hög hastighet som möjligt. Att låta data gå genom kortet var det första steget. Efter det skulle förhoppningsvis ett stabilt system ha uppnåtts där vi kunde göra överföringen av data snabbare.

The objective of this thesis is to make a training material for KSU, which shows how radiation affects the different electronic components in a radiological environment.All electronic systems in the presence of high ionizing radiation can experience difficulties and be destroyed.This influence may compromise the control system and thus the safety of a nuclear reactor plant.To achieve this objective requires a description of electronic components and sensors, to better understand its function.This thesis will also show the possible solutions available that the author found interesting.Organizations such as NASA, CERN and ESA have worked to develop electronic components immune to radiation. Those organizations have also developed a test protocol that guarantees to a certain extent the security of electronic components in a radiological environment.Since we know how the material reacts with the radiation, it could develop a material that can be resistant to radiation or like CMOS technology has proposed, to reduce the component to avoid the storage of charge in the oxide.Another solution can be the GRAPHENE. Its features will revolutionize the Electronics and provide answer to the radiation problems, Graphene will replace Silicium and the electronic components will only have a few nanometers dimensions so the oxide area also reduces, and in this way avoid the known problem of storage of charge..

Free Space Optics (FSO) has received a great deal of attention lately both in the military and civilian information society due to its potentially high capacity, rapid deployment, portability and high security from deception and jamming. The main issue is that severe weather can have a detrimental impact on the performance, which may result in an inadequate availability. This report contains a feasibility study for an all-optical free-space link intended for short-range communication (200-500 m). Laboratory tests have been performed to evaluate the link design. Field tests were made to investigate availability and error performance under the influence of different weather conditions.

The objective of this diploma work is to investigate a set of Multiple Input Multiple Output (MIMO) channel models compatible with the emerging IEEE 802.11n standard. This diploma work validates also advanced, innovative tools and wireless technologies that are necessary to facilitate wireless applications while maximizing spectral efficiency and throughput. MIMO channel models can be used to evaluate new Wireless Local Area Network (WLAN) proposals based on multiple antenna technologies. The purpose of this thesis is to investigate means of channel models and their implementation in different environments such as: Matlab, C++ and Advanced Design Systems (ADS). The investigation considers also a comparison between the channel models based on theoretical data and parameter setup to the channel models based on statistical characteristics obtained from measured data.

During test flights SAAB uses the data acquisition system COMET 16. The part of the system that receives the signals from the sensors and converts them is called KSM 15. The purpose of this thesis is to develop a data acquisition module on stacked PC/104 modules with a lower production cost. Our work has been divided into one part about analog signal conditioning and a second part with digital filtering and memory management of the sampled data. The analog part, designed of regular components like instrument amplifiers, voltage references, operational amplifiers and multiplexers, adjusts the sensors signal levels for the ADC?s that converts the signals.

In this Master's thesis, a direct-conversion receiver front-end has been designed in a 0.18um CMOS technology. Direct-conversion receivers (DCR) have obvious advantages over the heterodyne counterpart. Since the intermediate frequency (IF) is zero, the problem of image is circumvented. As a result, no front-end image reject filter is required and the channel selection requires only a low-pass filter, which makes it easy to integrate directly on chip. However, the DCR also suffers from several drawbacks such as extreme sensitivity to DC offsets, 1/f noise, local oscillator (LO) leakage/radiation, front-end nonlinearity and I/Q mismatch.