This thesis analyzes the expected profitability in land based wind power plants. The expected profitability is calculated on the basis of a wind power project in Vartofta, Falköping. The information required to calculate the expected outcome is then concentrated to this project, which is in this thesis called project Näs. In project Näs they plan to build three wind power plants, with each an effect of 2 MWh. These wind power plants are very capital intensive investments with a long and uncertain payback time.

The energy sector is facing an impending paradigm shift. Today?s technology enables the end-user to generate their own energy locally at home. Furthermore, recently developed storage technologies make it possible to balance energy demand with stored energy and integrate district heating with the local power grid. This means that in the future heat and electric power will interact and energy flows is converted over energy boundaries.

Biogas is a renewable energy produced through anaerobic digestion, which means that organic matter is degraded by microorganisms under anaerobic conditions. The produced biogas can then be used for cogeneration, electricity, heat or upgraded to vehicle gas. Eskilstuna Energy & Environment AB has four digesters at Ekeby water sewage treatment plant, Eskilstuna. One of the biogas reactor (RK4) is equipped with a jet-mixing system while the remaining digester uses top-mixing. The mixing system is an important parameter to achieve optimum operating conditions for the process regarding gas production and degree of digestion.

An increased awareness about the global warming has created a demand for more information on how the climate is affected by different activities.This master thesis was initiated by Tricorona, a Swedish company that offers its customers analysis and calculation of their climate impact. Tricorona also supplies climate neutralisation with CERs, in accordance with the Kyoto protocol and controlled by the UN. This work demands updated emission factors for greenhouse gases. An emission factor gives information about the greenhouse gasintensity of a service or a product [kg CO2-eq./ functional unit].The purpose of this thesis is to examine how electricity, district heating, hotels, taxis, food and materials affect the climate and how emission factors for these areas can be calculated.This was done by reviewing and comparing different studies and by interviewing experts. The information was evaluated and recommendations on calculations and emission factors were made.The consumption of energy is the main source of greenhouse gas emissions for district heating, electricity, hotels, taxis and materials.

The energy consumption continues to increase as the use of electronics and energy consuming equipment increases. The use of fossil fuels has to be phased out for this to be sustainable in the long run while the use of renewable energy continues to increase. A renewable energy source is solar energy but the production of heat and electricity are today very expensive compared to other energy sources and an important task for the solar energy market to grow is therefore to minimize the production cost of the solar collectors while increasing its efficiency to produce heat and/or electricity. One way to convert solar energy into heat is by using solar collectors and electricity can be produced by utilizing the produced heat, or by applying solar cells.This thesis aims to recommend a reflective material for the next generation solar collectors from Absolicon and to recommend a commercially available coating for the receiver tube of the solar collector. A market study has been carried out to investigate the cost-related aspects along with the optical and durable aspects for the optical material of the solar collector.

To achieve the requirements to decrease emissions of greenhouse gases by 20 % by 2020, Swedenneeds to increase its use of bioenergy. In doing so it seems natural that those who already haveaccess to large amounts of biofuels in the form of by-products such as straw, wood chips anddigestible materials take advantage of these assets locally. By combining production of heat withpower production at the farm it may be possible to not only reduce the direct use of fossil fuel forheating but also reduce energy costs.The purpose was to simulate different cases of using a small scale biofueled combined heat andpower plant for farm-based systems. A MatLab-model was developed and used to draw conclusionsabout the costs for production of heat and electricity with different conversion technologies.The model uses climate data to simulate the variations in heat energy demand on a day-to-day basis.The given heat demand is the base of the simulation and from this the possible electric output iscalculated. This study has focused on the impact of the following properties: electric-, heat- andtotal efficiency, fuel, fuel price and specific fuel requirements.

An energy calculation model for Swedish houses   that is fast, flexible and user-friendly has been developed within the   framework of this thesis.  The model   also provides a set of actions which may be investigated in the model based   on savings and payback period. Energy use in a house depends on the technical   conditions, such as building envelope and heating systems, which outdoor   climate the house is exposed to and who lives in the house. Energy use for a   house can be divided into heating, hot water and household electricity. There   are several methods to calculate the energy use of a house. This report   summarizes the methods that may be suitable for a fast and user-friendly   calculation model.

Sweden has long had access to low electricity prices due to the wide availability of hydro and nuclear power. This has now changed because of today's rising electricity rates resulting in increasing heating costs for properties, especially in the properties with electric heating systems."Ankaret" is a parish for "Svenska Alliansmissionen", which is located at "Gullbrannagården".The parish has installed electrical radiators and an exhaust ventilation system that makes the energy demand high due to the large ventilation flows. The building was built as the price of electricity was still low and would reduce energy use today by combining its heating system with an air/air heat pump. The heat pump delivers more heat into the room than the electrical energy that it uses. This lowers the electricity needs.

An analysis of a specific application of anaerobic wastewater treatment at a pulp and board mill, Stora Enso Skoghall, was carried out. A literature study was done and effluent wastewater from CTMP pulp production was analyzed. The analysis consisted of a broad constituent analysis and an anaerobic treatment trial. Results from these test where used to calculate the treatment effectiveness and resulting energy potential at the mill.The literature study and constituent analysis showed that toxicity of the water to be treated, due to wood extractives and sulphur content, was of concern. Detoxification chemicals targeting these constituents where used in the anaerobic treatment trial.

This report that is written in cooperation with Peab Sverige AB, studies the information and knowledge management from the production support to the production management. The conclusion of this report is that to have a good and functional information and knowledge management it is necessary that the company has a good way of regain and handling experiences from its projects. The way to do this is to develop the managing system on the production management?s terms. It is also critical to find an easy way for the production management to use the system..

A large part of the time losses in production in modern manufacturing industry are a cause of unplanned interruptions in production. In this essay we have studied the effects of an unplanned interruption in production. The study was performed during one month on a press production line at Volvo Cars Body Components (VCBC) in Olofström. The effects of the interruptions have been studied on the basis of two perspectives of the environment of the production. The study started at the level of automation and was mainly done as a survey of the unplanned interruptions in production.

ABB Capacitors is looking to introduce LEAN within their organization. The purpose of this research is to suggest ways to improve the production planning in order to facilitate the company?s production processes. This should be done in accordance with the LEAN concept.Today, ABB will produce two of the customers? orders at the same time.

The objective of this work was to introduce measures to reduce energy and water demand at Gävle Söder 17:10. To succeed, this energy audit has been made. The work is based on collected statistics from the property owner Norrporten, measurements, literature review and through consultation with experts in the field. Two models, one for each building, have been created in the simulation program BV2 to estimate the potential of energy measures based on the collected information. The models in BV2 have been verified against the statistics of the energy consumption.With the help of calculations and simulations, seven cost-effective measures have been identified.

The purpose of this study is to investigate how much of the estimated annual electric energy production from Swedish wind power that actually was produced, as well as the history of this agreement over time. The aim is to also examine if there are properties that have caused some group of wind power plants to produce more or less, compared to their estimated production. Operational data on wind turbines collected by the Swedish Energy Agency was analyzed. A survey was made among owners of wind power plants with a nominal power of at least 2 MW. Two different methods for normal year correction of production data were used and compared.

The report is about efficiency of a current production group where there is no clear production flow and there are some buffers between the operations. The efficiency is done with the help of a tool that is calledWork process of flow production which is used by Atlas Copco CTO. The most obviously results are that the lead time drops from 25 hours to 425 minutes and that the balancing loss decreases from 85 % to 8 %. The report focus on decreasing transports, decreasing buffers, more reliability in lead time and quality. And a more stimulating labour content for the workers is another result..