As an amateur it can be difficult filming from several angles at the same time as this requires several cameras. It´s also hard to film at occasions when it´s not appropriate to manoeuvre the camera manually. Systems for solving these problems already exist, but it´s either more expensive, professionalsystems or cheaper systems with limited functionality.The purpose of this project is to develop a cost efficient solution to the problem above that offers a better functionality then existing commercial systems. The biggest difference from existing products is the wireless video feedback from the camera to the remote unit.The result of the project is a system consisting of two units, a manoeuvre unit with a cradle for the video camera and a remote unit from which the operator can control pan and tilt of the video camera.Communication between the two units is wireless.On the remote unit there is a joystick and a display mounted. In addition to this, there is also an IR receiver that is capable of reading the signal from the cameras own remote and sending it to the manoeuvre unit.The manoeuvre unit is equipped with one motor to control the tilt function and one motor to control the pan.

The purpose of this thesis is to evaluate and update load curves for Fortum Distribution AB. Theload curve method is a tool used to forecast the strain of an electric grid. The method is based oncustomer annual energy consumption, outdoors temperature as well as customer category. Theload curve method was established by Svenska Elverksföreningen at the start of the nineties andfocus was put on standardizing annual energyconsumption, in order to make the method usableacross the nation. Present consumption patterns have changed since the original load curves wereproduced, which leads to a need to update the load curves.The work began with an update of present load curves according to recommendation taken fromanother earlier thesis.

Problem: Our opinion is that it is important to consider about usability in system development. In this thesis we will focus on usability in point-of-sale systems. The point-of-sale system we base this thesis on is Extenda Retail. Our case study is performed on Ica Kvantum in Bromölla, which implemented Extenda Retail about two years ago. Purpose: The purpose of this thesis is to figure out what important factors there are to consider, in usability aspects, when developing point-of-sale systems, with focus on the cashier.

An important task for Region Skåne is to allocate resources to the health care districts. From 1999 to 2002 Region Skåne used needs-based resource allocation as a model for allocating resources. In a needs-based resource allocation individuals with the same socioeconomic and demographic characteristics are assumed to have the same level of need and are therefore allocated the same amount of resources. During the period of needs-based resource allocation a matrix model was used as a method. In the matrix model individuals were divided into cells after each combination of the socioeconomic and demographic variables.

The master thesis, conducted at Metrima AB, concerns the development of a non-intrusivedistribution meter as a basis for individual tap water billing in apartments.The project is conducted in response to the market interest in individual tap water billing inapartments as an answer to environmental concerns regarding water consumption. Due to thehigh installation cost of traditional water meters, a new method of determining waterconsumption, without having to cut water pipes, is proposed.The proposed method distributes the total water consumption for an apartment complex toindividual apartments according to distribution meters, measuring water run-time, in eachapartment. The water run-time is estimated by measuring the water pipe?s outward vibrationsand temperature changes.A test environment was established and a prototype built, using a tilt- and vibration sensor forvibration sensing and a precision temperature sensor to measure temperature changes. As bothsensors work well in the test environment, further testing was done in 3 apartments for aduration of 5 days.

Scania Top Team is a competition where the best mechanics in the world are competing against each other. In 2011, the world final was recorded and this material is now used to see which problem solving strategies these top of the line teams are using to solve the realistic problems assembled in front of them. To help them, the mechanics are allowed to use two of Scanias IT-systems: Scania Multi and Scania Diagnose and Programmer 3. This report consists of two parts. The first part is the development of a method to analyze the recorded material.

This thesis report describes the development of concepts regarding how weight can be reduced to the analytical instrument Biacore 4000. This thesis has resulted in five different concept proposals, all of which is solutions to reduce the instrument's weight.The thesis started with a pre-study where the instrument's structure and function were studied using both Solid Works, the opportunity to study the instrument in real life were also possible done. During this phase, a weight study was conducted as well, in which the instrument's weight distribution was studied and mapped.Following the initial phase, the work proceeded by developing concrete concepts to reduce the weight of the instrument where focus mainly was on the two cabinets. In addition, another two concepts were revealed, both with a more general approach.At the final phase of the thesis, the concepts were compiled and evaluated among themselves and the initial instrument.The thesis resulted in a study of the instrument's structure and weight distribution, with suggestions on how weight may be reduced for the instrument.The result factors such as materials, and manufacturing were aspects that were taken into consideration.At the final section of the report, suggestions for further work in which different aspects are discussed can be found..

This thesis studies the concept of balance in the management control systems (MCS) of a small Swedish company within the IT-sector. The aim is to evaluate the importance of balance and dynamics in MCS and investigate which factors affect them. The frameworks used are Simons (1994) four levers of control, and the five-factor model for balance and dynamics by Mundy (2010). The small IT company - the object of the case study - has grown extensively in the last years and needs to develop more formal MCS without losing efficiency and creativity in their fast-moving industry. The case study reveals that balancing MCS is important also in smaller companies with less formal MCS.

2 (45)AbstractAuthors: Gunnel Forssell Ehrlich & Alexandra WinbergTitle: Gender in local press ? a quantitative study of four local newspapers Level: BA Thesis in Media and Communication StudiesLocation: Linnaeus UniversityLanguage: SwedishNumber of pages: 50The report shows a quantitative study of balance in gender and position of power in the local press. The study aimed to shed light on the distribution of space in the newspaper between men and women, those within power and those without in Swedish local press. The study was conducted with four newspapers, during a month of time with local editorial news material. In our study, we have assumed Lippmann?s and Strömbäck?s theories of pseudo-reality and distribution of gender and position of power in Sahlstrand and Jarlbro.

The mainpart of this thesis is about the developing of a new analysis tool to be used in Zenicor Medical Systems AB ECG-system. The primary task of the system is to simplify the ECG survey for patients who suffers from different kinds of arrythmias, for example heart fibrillation. With this system is it possible for the patients to do their ECG survey by them self at home and then send the signal with their telephone or mobilphone to a server. The equipment used to do the survey is not bigger than you can have it in a pocket and this results in a bigger flexibility for the patient. A doctor can connect to the server and analys the ECG-curve and follow up the patients condition..

The existence for companies today consists of constant challenges with customers that want more individual products with high quality as quickly as possible. For a company to be able to have a short delivery time, it must also have a short production time. This makes streamlining and improvement of processes a big part of a company?s workThis thesis has been carried out together with the company Lasermax Roll Systems AB, a world-leading manufacturer of feeding, finishing and monitoring systems for high-speed digital printers. They manufacture their products according to the assembling for costumer order principle.The purpose with this thesis is to map and analyze, the assembling process and the test process at Lasermax Roll Systems AB.

Today significant resources are provided to improve the digital work environment within the Swedish healthcare to create efficiency, good work environment and patient safety. Despite this, major flaws are shown by the lack of communication between the eHealthcare systems. This becomes a stress factor among healthcare professionals because of increased administration and decreased physical contact with patients. The purpose of this study is to create a understanding of the concept of interoperability at different levels in the eHealthcare systems. This has been conducted through a qualitative interview study at a healthcare center where the respondents have been describing their digital work environment and the way it works today.

Problem: Our opinion is that it is important to consider about usability in system development. In this thesis we will focus on usability in point-of-sale systems. The point-of-sale system we base this thesis on is Extenda Retail. Our case study is performed on Ica Kvantum in Bromölla, which implemented Extenda Retail about two years ago. Purpose: The purpose of this thesis is to figure out what important factors there are to consider, in usability aspects, when developing point-of-sale systems, with focus on the cashier. We also wish to find out the cashiers opinions about the Extenda Retail system. Method: The information gathered for this thesis consists of literature and interviews.

The objective of this study was to make an inventory and a potential analysis of the organic beef production in the region of Gävleborg, Sweden. A survey was conducted, where a questionaire was sent to all farmers in the region who had environmental subsidies concerning organic cropping systems in 2001. In total, there were 701 farmers, of which 46 % participated in the study. Three slaughter houses were interviewed to get their pictures of the development of organic beef production. The study shows that there are potentials and interests in the region to increase the production of organic beef.

This master's essay is about seasonality in Bristols slave trade until the American Revolution 1776. The essay uses the Voyages database as the primary material. The essay's method is to study monthly distribution at different points of the slave trade ? the departure from Bristol and the arrival at the American destination. The seasonality of slave purchases in Africa is primarly studied through the monthly distribution of departures from Bristol for a specific region in Africa.