In recent years, existing solutions for cooling personal computer CPUs have been supplemented by a new product category, factory sealed water cooling loops. These systems, consisting of a water block with an integrated pump, a fan and a radiator, perform well compared to the air cooling solutions but are less effective than larger, custom-built water cooling systems.This project aims to explore the most important aspects of a factory sealed system and to identify possible cost-effective enhancements of the performance.The most significant differences between the different groups of water cooling loops are the block design and the pumping power. The performance of both categories is also largely dependent on the fan power, but increasing fan power has a large negative impact on the noise level.Both radiator size and fan model choice appear, in tests, to be relatively unimportant, presuming that the noise level is kept constant. The position and direction of the fan, however, has significant impact on both the temperature and the sound level.Water blocks can be designed in several different ways, both regarding the heatsink design and the flow direction. In simulation, flow with the inlet centered above the heatsink result in considerably lower pressure drop and slightly higher temperatures than flow through the block, for heatsinks with fin arrays.Creating a competitive product in this product segment certainly seems possible, as there are performance-increasing changes to be made that seemingly has little impact on the production cost.

Sitka spruce (Picea sitchensis) is not considered to be a native species to Swedish forests. It´s origin is the pacific coast of Northern America, an area that is dominated by a coastal climate which makes it likely to believe that it would be well suited for growing in the south-west of Sweden. This study aims to investigate the gain in production that can be reached by growing sitka spruce instead of Norway spruce (Picea abies) in the county of Halland. A regression model based on data from forest experiments was produced to explain the gain in production. This model was based on elevation and annual precipitation. The model was then used to create a map layer in arcGIS that shows the gain of volume in comparison to Norway spruce in percent. An analysis was carried out to find what share of the forestland in Halland county that fell into four different classes of production gain.

The company Olofsfors AB manufactures drive belts for forest machinery, known as ECO-Tracks, and abrasion-resistant steel and cutting edges for graders, excavators and tractors, known as Bruxite and SharqEdges. Manufacturing these products requires the steel to be heated and molded, then submerged in water and hardened. The water used in the hardening of steel is pumped to the process from pits below the floor and then pumped back to the pit after it?s been used. Since the temperature of this water rises after being used to harden the steel the temperature of the pumping pit needs to be adjusted to maintain its setpoint of 21°C.

The empirical data used for this master thesis, consists of eight manuals with the main purpose to help students evaluate information resources found on the web or Internet. The purpose is to elucidate the discourses and investigate those textual characteristics, which figure in the investigated manuals. The method used is a discursive and linguistic approach, with a power/knowledge discussion applied to the results. The analysis identifies, among other things, the production and consumption of the investigated texts, and that the manuals function as a reflection of the relationship between the participants in the situation, the sociocultural practice of the institution and its identity..

Many companies do not register all the stops that occur in a production plant, it often takes longer to report than to fix the problem. If no problems are registered, you cannot trace where the problems arise.This master thesis was performed at AcobiaFLUX and they have noticed an increased demand from their customers to trace problems raised in their processes. The aim of the thesis was to find out how a tool to monitor a process best could be developed. Then the most essential from the theoretical base was developed into a useful tool for operators. For the operators to know if the process utilizes the full capacity of a process, the tool presents a measure of the Overall Equipment Efficiency, OEE.

2 (45)AbstractAuthors: Gunnel Forssell Ehrlich & Alexandra WinbergTitle: Gender in local press ? a quantitative study of four local newspapers Level: BA Thesis in Media and Communication StudiesLocation: Linnaeus UniversityLanguage: SwedishNumber of pages: 50The report shows a quantitative study of balance in gender and position of power in the local press. The study aimed to shed light on the distribution of space in the newspaper between men and women, those within power and those without in Swedish local press. The study was conducted with four newspapers, during a month of time with local editorial news material. In our study, we have assumed Lippmann?s and Strömbäck?s theories of pseudo-reality and distribution of gender and position of power in Sahlstrand and Jarlbro.

Today produces the wind power 2,5 TWh (TWh = terawatt hours) of Sweden?s total energy input of around 620 TWh. The Parliament has adopted a national planning objective where the wind-based electricity production will increase to 30 TWh in 2020. This requires that landowners will leas there land for wind power to wind energy companies. Such land leasing means that the landowner's business is considered to be a multiple-use.

Drinking water from drilled wells has a high content of iron and other minerals in many places in Sweden. Questions about the association between the quality of drinking water and the health of dairy cows are regulary asked both by advisers and dairy farmers. There are so far not many studies published about the relevance for high iron content in water and dairy cow health and production. Therefore, the aim of this study was to investigate if there is a connection between the iron content in water and the health of dairy cows. Initially a literature study was made about iron and it´s function in ruminants.

Since 2004, wind power has had the largest installation of new capacity compared to other energy sources in Sweden. Accommodating new wind power may require strengthening or rebuilding of the existing grid in areas where the grid is already loaded to maximum capacity. This master thesis examine the possibility of a new 400/130 kV substation in Yttermalung, Sweden, with a connection to the two neighboring regional grids in Dalarna and Värmland owned by Fortum. This substation would provide a new connection point to the Swedish transmission system as well as an interconnection of the two, currently separated, regional grids. Different expansion scenarios where a substation with and without series compensation or a phase shifting transformer (PST) to control active power flow were studied.

This paper is about the new methods and metrics used in industry and business today striving for better revenues and larger market shares. It investigates the relations between the old fordistic and tayloristic way of manufacturing and compares it to the models used in industry today for being competitive, seeking to please customers and becoming more flexible. More specific the paper is about if Six Sigma and lean production are the key for succeeding these days. SKF:s factory in Gothenburg and other companies will make an example for how these methods are used in practice.The aim is to try to answer if these systems with inherited tools and methods are the right way to get the flexibility that is needed for being able to deliver the right goods to customers and market. For a company to be flexible decisions must be made fast and needed changes must be able to be done easy and without too large costs and investments.

This candidate thesis contains the possibility of expand the Swedish photovoltaic market through photovoltaic cooperatives and a photovoltaic exchange. In the current situation there is a lot of problems with production of electricity from photovoltaic, that?s why we show some possibilities how to avoid these. To understand the problem with photovoltaic produced electricity we first give you a background.We show how to expand the Swedish photovoltaic market by describing how a photovoltaic cooperative and photovoltaic exchange could work in Sweden. It have been confirmed from our market research that the interest of photovoltaic cooperative and exchange is high.To find out how profitable photovoltaic is in Sweden, have three projections been made.

The purpose of this report was to compare Lilluns egg production with other Swedish egg producers based on the flow of nutrients (nitrogen, phosphorus and potassium) in the egg production systems. The main focus in the report was the utilization rate of the forage and the excess of nutrients per kg egg. Additionally, the purpose was to identify the environmental impact from Lilluns egg production and compare the results with other egg producers. The inflow of nutrients associated with forage and poultry was compared with the nutrients that were exported from the production. All of the egg producers in this study had an excess of nutrients.

Detta examensarbete handlar ?Verklighetstrogen Effektskomposition?. Målet med arbetet är att undersöka och utnyttja alla de olika aspekterna som gör att en film med specialeffekter känns så verklighetstrogen som möjligt. Arbetet handlar om de olika delarna i en filmproduktionsfas så som pre-production,production och post-production. Filmen som skapas är en specialeffektsbaserad hemmavideo som har som syfte att vara så chockande som möjligt i förhållande till vad man förväntar sig när man börjar kolla.

Sustainable beef and milk consumption. The consumption of beef and dairy products in Sweden is high. A lot of greenhouse gases are emitted from the production of these products. The production of beef in Sweden has decreased but the import has increased. The number of dairy cows has decreased while beef-production with suckler-cows has increased in Sweden.

The task was to design and manufacture a submersible displacement pump working with the wobble plate principle. The main task for the Wobble plate pump is to be used as a sewage pump for smaller households or dewatering pump in environments where small flows and high pressures are acquired. For these purposes ITT Flygt sell a screw pump, PC-Grinder 3068. The hydraulic part of the PC-Grinder is manufactured by a subcontractor. Therefore ITT Flygt wants to evaluate an alternative to their screwpump PC-Grinder, which can be entirely manufactured by them self.