The aim of this study is to evaluate an alternative projection of the Medial Coronoid Process (MCP) of the canine elbow joint. The projection (Di35M-PrLO) was, to my knowledge, first mentioned in an article by Haudiquet et al in 2002. In that article the projection was tested in vitro, and a good sensitivity was showed for the Medial Coronoid Process. The projection might be helpful in cases of suspected Fragmented Coronoid Process (FCP) . This study is divided into three parts. The first part is an in-vivo test of the projection, including technique and subjective evaluation of the outlining of the MCP.

The project was intended to produce a brush simulation plugin to the image processing program GIMP which would use a 6DOF drawing tablet for user input.Too ambitious goals coupled with compability issues between the resources used resulted in that no meaningful software was produced. Experience was however obtained, and this paper is intended to give an overview of relevant concepts for- and the process ofcreating a brush simulation..

The aim of the study was to investigate if methane emission in a constructed wetland changed in a diurnal pattern correlating to temperature, humidity or light conditions. The gas measurements were carried out with a static chamber technique. The wetland (in Nykvarn outside of Linköping, Sweden) takes care of wastewater to reduce the nitrogen loads. Measurements were carried out at three different occasions in the summer of 1998 on two sites in the wetland. One site was close to the inflow, inhabited by Lemnaceae, and another site was located further downstream inhabited by the emergent macrophyte Typha latifolia.

New high strength steels require improved cold rolling techniques. The aim of this degree project was to develop a new and money saving cold rolling technique to manufacture steel strip for saw blades. The work is based on earlier rolling experiments made with a high carbon steel grade at LuCoil Steel AB. The work also focused on the mill requirements to cold roll high strength steels. The results show that LuCoil?s existing cold rolling mill was actually designed for rolling low carbon steel.

AbstractThe purpose of this bachelor thesis is to describe the use of artificial insemination (AI) in sheep and discuss the possibilities for AI in Sweden. Male and female fertility, heat detection, semen handling and insemination techniques in sheep are described. Advantages and disadvantages of AI are discussed. In order to achieve genetic progress it is important with well planned and implemented breeding programs. The Swedish Sheep Recording Scheme and computer software from Elitlamm are the basis for sheep breeding in Sweden.

One important issue faced by companies is to secure their information and resources from intrusions. For accessing a resource almost every system uses the approach of assigning a unique username and a password to all legitimate users. This approach has a major drawback. If an intruder gets the above information then he can become a big threat for the company and its resources. To strengthen the computer security there are several biometric methods for identity verification which are based on the human body?s unique characteristics and behavior including fingerprints, face recognition, retina scan and signatures.

Over the last decades, language in the public sector has changed due to influence from New public management. In this thesis, I seek to investigate librarians? attitudes towards a more businesslike way of speaking about libraries, referred to here as management-speak. For this purpose, I?ve used a modified version of the matched guise technique.

As a part of the fight against the global warming the energy production needs to be more efficient and redirected towards sustainable options. One alternative is cogeneration, which means that electricity and heat is produced in one plant. The purpose with this survey is to examine if there are any commercial available combined heat and power techniques, based on combustion of solid moist biomass, which are suitable to small-scale applications. The technique must be able to produce between 2 and 10 MW thermal and the heat demand is a Swedish district-heating system. When already published reports had been studied, the Organic Rankine Cycle (ORC) was chosen as the most suitable technique.

Syftet: Syftet med studien var att beskriva hur omvårdnadspersonal inom kommunens särskilda boende och korttidsboende upplever att vårda personer i livets slutskede.Metod: Studien bygger på åtta kvalitativa intervjuer med undersköterskor. Datainsamlingsmetoden baserades på Critical Incident Technique och som analysmetod användes kvalitativ innehållsanalys. Resultat: I intervjuerna framkom att samarbetet till de övriga i teamet och närstående hade en stor och avgörande betydelse för hur vården utvecklades. Omvårdnadspersonalen kände ibland att sjuksköterskan saknades i vissa omvårdnadssituationer. Fördelning av personal under dygnet bidrog till kontinuitet i samverkan.

There are many children in Sweden today, approximately 200 000, who have parents or a parent that abuses alcohol or other drugs. The aim of this study was to investigate how group leaders in support groups for children with addicted parents relate to this sort of support groups. What are their advantages and disadvantages, according to the group leaders?The method used was qualitative and the empirical material was collected through group interviews. We have interviewed eight persons who are social workers and the interviews were carried out at three work places.

Uppsats för avläggande av filosofie kandidatexamen iKulturvård, Konservatorprogrammet15 hpInstitutionen för kulturvårdGöteborgs universitet2014:26.

Rock singing - five vocal teachers´ experience of the female voice.The purpose of this study is to find out what different vocal teachers have to say about rock singing and the female singing voice. The method I have used to gather information is a phenomenographically inspired qualitative interview. The study begins with a few thoughts about my interest in rock singing, followed by a short overview about other research and literature that has been published on the subject. I have interviewed five vocal teachers in this study. All of them with many years experience of singing, both singing themselves and teaching professionally.

The agricultural sector is currently highly dependent on fossil fuels, with diesel beingmost prominent. There are however both historical and modern alternatives thathave not been subject to enough evaluation to disregard them as suitable alternative.This report aims to theoretically investigate the feasibility of converting aconventional diesel driven tractor to run on electricity, delivered via a cableconnected to either the main power grid or on-site electric production, such asphotovoltaic. Delivering electricity to the machine via a cable is a method withhistorical roots in the early 20th century and in the present day mining industry.The economic and technological potential of the technique are evaluated, along withthe examination of several different motor powers, voltages, losses and constructionideas. The report finds the technique to be both possible as well as long termeconomically and environmentally beneficial. To realise this method however, somedeviations from the present methods of agricultural farming must be made,considering the more advanced driving patterns, the limited mobility and therequirement for extra driver awareness.

The aim of this Master?s thesis is to investigate if the library can be a real partner for researchers in managing and dealing with their research information. In this study, six researchers have been interviewed about their problems with information management. This study uses the method Critical Incident Technique for the interviews with the researchers. This method focuses mainly on problems and what happens around those problems.

In this Master thesis, microwave connections between circuit boards are constructed. The primary frequency band is the X-band (8-12 GHz). The purpose of the connections is to enable a more simple and cheaper way of mounting the circuit boards inside a container. The connections have been designed and evaluated, using different computer programs. A few prototypes have been built and measured.