Examensarbetet är utfört på Albin Components i Kristinehamn som med gamla anor inom motortillverkning och komponenter till motorer har specialiserat sig på transmissionskugghjul till tung fordonsindustri.Projektet har gått ut på att analysera ställtiderna på kuggcellerna 3, 6, 8, 5 och 7. Förutsättningen för att använda produktionsfilosofin Lean Production och dess bruk av små batcher är att ha korta ställtider. Ställtiden är den tid som en maskin står stilla under bland annat byte av verktyg inför körning av en ny order. Då inget produceras under ställ är det en spilltid och som all spilltid måste det reduceras till ett minimum.SMED- metoden (Single Minute Exchange of Die) är en metod för reducering av ställtid där stället delas upp i OED (Yttre ställ) och IED (Inre ställ).Analysen har till stor del kretsat kring tidsåtgången för mätning i mätrummet som är en stor del av ställtiden. Dessutom undersöktes möjligheten att minska tidsåtgången vid själva ställets utförande och kommunikationen mellan operatörerna och mätrummet.För att uppfylla målen har kvalitativa och kvantitativa undersökningar gjorts.

Hair care is a hygienic treatment and is supervised by the Local Environment and Public Health Committee in the municipality. According to the Swedish Environmental Code, hairdressers as all practitioners are required to take measurements to protect the environment and public health. In hygienic treatments hazards may arise from inadequate hygiene practice which spread infection. Hazards may also arise from the use of hair care products such as permanent wave solutions, bleaches and hair dyes. Some hair dye components are known to cause contact allergy, mostly in hair dressers who are exposed professionally but also in some cases in consumers.

This thesis work aims to describe the prerequisites for a distributed treatment platform for real-time sharing of rounds performed by paediatric oncologists. The work started during the autumn 2004 and is directly aimed at improving the situation for the thirty or so specialist treating children with cancer. The work is not limited to the description of such a platform but also to select suitable software and hardware for the implementation of the platform and further more to coordinate the implementation. The production of several documents describing the platform is also part of this work. The work successfully led to the implementation of such a platform as described in the published article Barnradioterapi på distans Kristenssen et.

In a time of fierce global competition, where an immense amount of commercial messages reaches consumers around the clock and in every conceivable context, companies constantly seek to find new ways to reach out with their product. One way to do so, that has increased in popularity in recent years, is the use of gift bags. A gift bag may contain samples, miniature products and even products in full size, as a rule from several different brands, which the recipient receives free of charge. The gift bag is typically distributed at some form of event, such as store openings, fashion shows, theme parties and the like, and the receiver of the gift bag can then evaluate the content without any obligation to purchase. The ambition of the companies that choose to participate with their products in a gift bag is, of course, that the recipient will find their products satisfactory, and ideally, that he or she will continue to consume the brand in the future.There are numerous scientific research contributions related to the use of free samples, but very few that concern the gift bag, where a collection of samples from different sources and brands appear.

This degree project has been performed along with Classic Garden in Gothenburg andBallongfirman Far & Flyg in Stockholm. Together we have developed a sun- wind- andrain protection. The protection is permanently assembled and mainly intended for publicenvironments as restaurants and outdoor cafés.The design on the sun protection was already done so our task has been to develop theconstruction and to build a prototype in scale 1:4 and one in scale 1:1. The look of thesun protection is approximately as the name implies, equal an igloo. The lamellae aregoing to fold out in different steps all the way down to the ground and the both sides willbe independently of each other.The first stage in the project was to develop differently principle proposal on how thefunction will work when folding in and out the protection.

In this essay, I want to achieve an accessible and applicable entrance to Alexander Technique as a method for learning to use the body in such a way as to allow emotional expression in music. It is necessary to see the real need of Alexander Technique for the active musician, and therefore important components of music-making will be presented. These components are presented from an Alexander-perspective in order to produce a clear picture of the method of application.The prerequisite for emotional expression in music is musicians and music listeners with the ability to generate, and respond after emotional impressions. Alexander Technique provides an approach to make it easier for musicians, especially guitarists, to express emotions in a performance situation.After years of practice and obtaining musical knowledge and practical skills at the instrument, it is common that muscle tension and ingrained patterns contribute to limited expression. Muscle tensions arising from pressured situations such as auditions, competitions and concerts.

To design new and high tech products the engineers rely more and more on computer based simulations to investigate the properties and behavior for a component or system.To verify these computer based simulations the dynamic properties for the components of the drivetrain needs to be verified. Therefore measurements of the stiffness and vibrations for the rear axle has been performed. This report show how the measurements has been implemented and evaluated, along with some interesting results for the rear axles properties.The static stiffness for the drive shaft along with the axle-gear has been determined. It is found that the stiffness for the whole rear axle is near the stiffness for the drive shaft, which means that the drive shaft becomes the dominant component of the system and affects the rear axle stiffness the most. The measured stiffness of the driveshaft is close to its theoretical stiffness.The stiffness for solely the hypoid-gear have been calculated using the stiffness for the rear axle and driveshaft, and thus has a range for the stiffness of the hypoid gear been determined.The backlash for the whole rear axle and for some individual components has been determined, where the backlash between pinion and crown-wheel has negligible impact on the total backlash.Measurements of the crown-wheel and pinion movements have been conducted, where the direction of movement is consistent with the theoretical direction of the forces.The vibration measurements show that the vibrations are more severe at certain rotational speeds.

DV01 is a bicycle concept aimed towards a contemporary target group, that considers the bicycle to be both a convenient means of transportation and a product with a high aesthetical value. A bicycle is for many people something that you attach to your own personal style, were not only the bicycles function but also its appearance plays a crucial role. It is also a product that consists of many different components and parts, which all affect the overall impression. The focus of the project has therefore been about finding a balance in the design. When form and function interact in a successful symbiosis, the result is often that the product may last longer and are more loved by its users..

The aim of this study was to investigate the knowledge of caries and gingivitis among third to fifth grade school children. A questionnaire was distributed to 117 children of a primary school in the south of Sweden. The result of the study indicate that the children had good knowledge regarding development and prevention of caries and gingivitis. However, the children did not know the meaning of the words caries and gingivitis. The children also appeared to lack important information about dietary measures to achieve good dental health.

Previous research has shown that internal communication can be linked with how motivated a project team is, but research that shows examples of how this works is missing. This paper therefore aims to study how two different IT projects are working with internal communication. By analyzing its strengths and weaknesses, we wanted to study how these could be linked to the project team's motivation. In doing so, we wanted to be able to give examples of how projects could work with internal communication to motivate their project teams. Essay questions of the study are:? How does the internal communication occur in the projects?? Which strengths and weaknesses are to be found in the internal communication?? How does the internal communication influence the project members' motivation? To fulfill the purpose of the study it was needed informants interviews with the project manager for each project to access the facts, and respondent interviews with the project members from each project for accessing opinions.The results from the interviews show that both projects have effective communication, even if it looked different, and doesn't quite agree with what previous research recommends.

Rapid Granulator is one of the world's largest producers of granulators, which is a kind of grinderwho grinds discarded plastics to granules which later can be reused when pressure molding plastics.The company wanted help in developing a new, or alternatively extending their previous,measurement equipment. The old equipment was hard to use, required changes in the code fordifferent measurement scenarios and had a limited array of measuring quantities. Rapid had an ideaof a similar concept only with a greater number of input ports, better range of applicable sensors andan advanced yet easy to use interface. The system is supposed to be placed at Rapid's test departmentwhere it will be used as a tool for finding faults and provide data which can be used for furtherdevelopment of the granulators.The project's members accepted the task and immediately began searching for suitable componentsfor the system. After the search was completed a list of costs, limitations, sensors, I/O's anddevelopment environment was presented to Rapid's staff.

This report deals with an exam report written by Olle Hjalmarsson and Thomas Likar, students at Högskolan i Halmstad. The project was carried out for Haldex Traction AB in Landskrona whose business consist of manufacturing automatic all wheel drive systems (AWD-system). These systems consist of a plate clutch which activates all four wheels of a 4-wheel driven vehicle. An important component in these clutches is the accumulator which basically consists of a piston under the load of a spring which creates an oil pressure with the help of an electric motor used for actuating the clutch.At Haldex difficulties has been experienced regarding the assembly of the accumulator parts due to the small tolerances between the piston and the hole of the accumulator in the cast aluminium housing. Attempts have been made to assemble the parts in existing robot cells.

Large areas of Lodgepole pine (Pinus contorta var. latifolia) were planted in the 1970s - and '80s. The purpose of the fast-growing species was to increase growth and with short rotation periods allow a rapidly increased harvest level. Today a large proportion of the young forests owned by Holmen Skog, Iggesund are covered by Lodgepole pine and an active forest management is required to spread the harvested volume over time which is desirable by a market perspective. The purpose of this essay is to investigate the possibility of spreading the harvested volume of Lodgepole pine over time.

Tomato production is a common and important agricultural activity in Nicaragua. During the last decades tomato producers have suffered great yield losses due to begomoviruses (family Geminiviridae). The genome of begomoviruses generally consists of two circular ssDNA components, DNA-A and DNA-B. Tomato yellow leaf curl virus (TYLCV) is an example of a begomovirus with only one component. An approach to manage the virus epidemics has been to breed a cultivar with begomovirus resistance genes, which have been transferred from wild tomato.

As requested by the company Husqvarna AB, we have developed a prototype of an electrical start device to a chainsaw. This was done through the development of new details in Catia, which has been integrated with existing details. Electrical components have been purchased by HAB electronics. In parallel with the modeling calculations was done, which was the basis for determine dimensions and the choice of an electric motor and gears. Prototype 1 improved gradually and led to prototype number 2, which became the final result.