The Master Thesis work this report is based upon has been conducted in cooperation with Svea Teknik AB. Svea Teknik is a consultant firm which is developing parts of a tunnel boring machine on behalf of Atlas Copco. The machine is being developed to mechanically excavate hard rock by fixating itself in the tunnel and then press a large rotating cutter-wheel equipped with Disc-cutters against the tunnel wall. The Disc-cutters are the tools that are in direct contact with the hard rock and are therefore exposed to extensive wear and needs to be replaced on a regular basis.The purpose of this Master Thesis has been to develop a service equipment that will enable time effective and safe changes of Disc-cutters. The Disc-cutters have a diameter of 17 inches and weigh about 130 kg.

ABSTRACTBackground: Most cases of lumbar disc herniation are asymptomatic. When symptomatic, LDH may cause a significant physical and mental distress. Initially, most patients are treated conservative but sometimes operations may be required.Aim: The aim of this study was to provide a review of the scientific basis of physiotherapy, including behavioural therapy, as a treatment to lumbar disc herniation regarding pain, function and the size of disc herniation in people suffering from lumbar disc herniation.Method: Four databases were used in the searches of literature. Assessment of the validity of the studies was done with the PEDro-scale and valuation of evidence rate was made according to guidelines made by the Swedish Council on Health Technology Assessment (SBU).Result: Nine RCT-studies were included with a total of 713 participants. The scientific basis is moderate to support a pain reduction and limited regarding improvement of physical function when it comes to physical exercises, including MDT.

Objectives: The purpose of the study was to examine if a pre- and post-operative difference could be seen in self-reported pain disability and self-efficacy among patients undergoing surgery as treatment for spinal disc herniation in order to improve process of rehabilitation.Method: A quantitative and descriptive design was used. 10 patients awaiting surgical treatment for spinal disc herniation were included at Akademiska sjukhuset (The Academic Hospital) in Uppsala. Participation was voluntary and the selection was made by convenience. Data was collected using The Pain Disability Index and Self-Efficacy Scale by which the patient would estimate how hindered they felt because of their pain in everyday activities and their self-efficacy to perform everyday activities. This was done the day before surgery and two weeks after surgery.

Uppsats för avläggande av filosofie kandidatexamen iKulturvård, Bygghantverk, 27 hp, 2012.

Uppsatsens syfte är att belysa hur vision, målstyrning och feedback upplevs av omsorgspersonal då de dagligen inte har tillgång till en fysiskt närvarande chef. För att uppnå vårt syfte har vi valt att genomföra en kvalitativ studie,i en mellanstor kommun som aktivt arbetar med vision och målstyrning sedan ett antal år tillbaka. Det empiriska materialet utgörs av fyra stycken intervjuer med omsorgspersonal utifrån semistrukturerade frågor. Våra frågeställningar är följande: Hur upplever omsorgspersonalen på självstyrande enheter implementering och förankring av organisationens vision i sitt dagliga arbete?  Hur upplever omsorgspersonalen på självstyrande enheter att målstyrning fungerar? Hur upplever omsorgspersonalen på självstyrande enheter möjligheten till feedback med en fysiskt frånvarande chef?   Vad anser omsorgspersonalen på självstyrande enheter om chefens närvaro/frånvaro? För att tolka och analysera vår empiri, har ett hermeneutiskt förhållningssätt och en abduktiv ansats använts.

Uppsats för avläggande av filosofie kandidatexamen iKulturvård, Landskapsvårdens hantverk15 hp, 2011.

In the last decades, high speed cutting has become an attractive technology in the wood industry. The possibility of reducing global costs in addiction with an increase in productivity, were the main reasons for the enlargement of the use of this technology. As usual, these advantages are accompanied by disadvantages that should be carefully analyzed. If on the one hand cutting forces are reduced with increasing cutting speeds, on the other hand, the centrifugal forces affecting the tool are higher. Exposed to such high loads, there is a considerable risk of tool failure that embeds hazards for both machine and workers.

The objective of this work was to compare the environmentally gentle soil scarification technique Huminmix (with possibilities to do track-grinding/HMMspår, long-scraping/HMMlångfläck and mounding/HMMhög) with conventional disc trencher, concerning seedling establishment and growth of direct seeded and planted Scots pine seedlings. Inventories were made during June and July 2005, in 34 seeded and 6 planted stands from 2000 ? 2004 (1- 5 years old) of lichen- and myrtillus/vaccinum-type in Holmen Skog AB´s district Norsjö in Västerbotten. The Huminmix-technique had been used for HMMspår in the seeded stands and for HMMhög in the planted stands (HMMlångfläck has been used from the year 2006 for direct seeding). The studied stands had been seeded with the same amount of seeds according to stand data.

In this thesis, two studies with different drills were included. In one of the studies two drills were compared: Väderstad Rapid and Väderstad Spirit. In the other study various drills for direct drilling were compared. The study with Rapid and Spirit was placed in two locations with different autumn tillage; one on ploughed land in Uppsala and one on cultivated land in Västerås, both with relatively high clay content. Rapid drills have a single disc coulter, while the Spirit drills have a double disc coulter. Various aspects were compared such as aggregate distribution, seed placement, emergence, crop yield and economic outcome.

This thesis is a product development project that was performed at Alfa Laval Tumba AB. In the past Alfa Laval have manufactured gas separators for engines where gas flows were cleaned from oil. A new business area for this kind of technology has shown to be the manufacturing industry where oil mist has to be separated from the vented air. Therefore a new and bigger design is needed to be able to handle the greater gas flows. A product like that would be a strong competitor on the market when the maintenance would be low in comparison to today?s equipment.During the project several concept suggestions were developed using customer interviews and research as input.

Hemp is an ancient cultivated plant that came to Sweden in the 1st to 2nd Century and was particularly interesting for use for food, clothing and building materials. Over time, other applications have been developed for hemp, e.g. in energy and health products. Interesting new uses for hemp continue to be identified and this fascinating plant has incredibly versatile applications.In this project, seed production of industrial hemp in Sweden was studied and evaluated. Five different methods are described, four of which are proven under Swedish conditions.

This thesis describes how the chip space and coolant channels are designed in today?s mills, the ideas behind the design and what is considered to be the best method of cooling. It contains ideas on how the chip space can be simplified. It contains several concepts on how the cooling could be designed for better efficiency and manufacturability. There are also suggestions on how the cooling could be stopped when the cutter isn?t cutting.

The aim of this thesis is to examine the characteristics of film cataloguing, and to compare general as in library use and specific as in archival use cataloguing rules. Most rules, both in archives and libraries, use the book as a point of reference. This is somewhat unfortunate on account of the great difference between books and films. The method used is studies of literature and qualitative interviews with three persons whose professional duties include cataloguing of films. The sets of rules which are studied are Katalogiseringsregler för svenska bibliotek KRS and The FIAF Cataloguing Rules for Film Archives.

Logosol is a company that produce small-scale wood processing products. To be able to expand the business Logosol have decided to increase exports, their target markets are the US, Russia, Germany and Norway. The expansion has mainly been through subsidiaries situated on the abroad markets. The subsidiaries have done poor results and that has influenced the whole company. CEO Bengt-Olov Byström made a decision to sell out the units to the people who worked in the business.

In Sweden, reduced tillage usually means non-inversion tillage, where primary tillage is carried out using chisel ploughs or disc implements. Primary tillage method is mainly determined by the desired soil loosening and the handling of soil residues. The effect of tillage depth was studied in field experiments in Skåne, Väderstad, Uppsala, Örebro och Västerås in different crops; spring oilseed rape, spring wheat, winter wheat and spring barley.The experiments generally had a randomized block design with the treatments mouldboard ploughing, deep chisel ploughing and shallow chisel ploughing, in some cases also shallow discing and no-tillage. In the experiments the following parameters were determined: seedbed properties, saturated hydraulic conductivity, penetration resistance, number of emerged plants and crop yield (all parameters were not determined in all experiments. Root growth and draught requirement were determined in two separate studies. There were no significant differences between tillage depths in non-inversion tillage in seedbed properties, plant emergence or root development.