This thesis describes teh solution of two problems regarding safety on powered lawnmowers; protectning the users from injury when using the lawnmower in slopes, and when cleaning the cutting blade.The task was carried out through initial studies on a representative lawnmower. A generation of ideas followed with an evaluation to select the best solution. The winning concept was further developed to reach acceptable performance. The word resulted in a functioning prototype utilising an original way of detecting inclinations without incorrect signals. It c an serve as a platform for further development into a product.The work gives insightful experience of solving real-world problems, and especially to deal with situations where several variables and their effects are unknownPlease note that several parts of the work are confidential, and have therefore been removed from the thesis..

This paper deals with knives excavated in the Birka Garrison between 1997 and 2004, in a selection of 100 knives out of approximately 400. The aim is to measure and analyze the material to find out if certain elements in design points to a specific craft. Two groups of knifeblades can be seen, one with a convex bevel and one with a flat bevel of the blade. Considering osteological evidence, historical sources, and the main suitabillity of the knives, it is concluded that some of the flat beveled knives may have been used for crafting leather and fur, whereas the convex beveled knives are of an allround type..

This report looks at the possibility of designing a universal adapter for Flat Blade windshield wipers in cooperation with European Automotive Supplier AB.To understand and see if this is possible, a research and an extensive patent search where done. Then to add structure to the project a Ganttschematic were developed. To generate good and solid ideas, different methods for product development were looked upon.When a method was chosen and applied, a series of concepts emerged. Now the focus was to design and construct all the pieces. The desired manufacture procedures were looked upon as well as materials.

The purpose of this degree-project was to investigate the possibilities for primary air preheating into the two smallest waste incineration boilers of Halmstad Energy and Environment. The investigation is a pre-study which has the primary goal to evaluate technical and financial offers from companies that manufacture primary air preheater, and investigate if it is technically and financially profitable to do a purchase on primary air preheaters in the future.In the pre-study it is proposed that it is most efficient to have individual primary air preheater, one for each incineration boiler and the primary air are also proposed to be preheated by hot water in the pre-study. Further in the pre-study it is proposed that the heat-exchanger should have plain tubes instead of finned tubes, to avoid getting dirty fast. The space in the boiler-room is limited, and therefore the major problem was to fit in the primary air preheaters into the boiler-room. By comparing the different offers from the companies, the result in the pre-study shows that the offer from the company C.A.

The purpose of this degree-project was to investigate the possibilities for primary air preheating into the two smallest waste incineration boilers of Halmstad Energy and Environment. The investigation is a pre-study which has the primary goal to evaluate technical and financial offers from companies that manufacture primary air preheater, and investigate if it is technically and financially profitable to do a purchase on primary air preheaters in the future.In the pre-study it is proposed that it is most efficient to have individual primary air preheater, one for each incineration boiler and the primary air are also proposed to be preheated by hot water in the pre-study. Further in the pre-study it is proposed that the heat-exchanger should have plain tubes instead of finned tubes, to avoid getting dirty fast. The space in the boiler-room is limited, and therefore the major problem was to fit in the primary air preheaters into the boiler-room. By comparing the different offers from the companies, the result in the pre-study shows that the offer from the company C.A.

 This report will describe a project between two students from Karlstad University and Markus Norström from Hovercraft solutions. The project aim was to develop a cabin for the hovercraft 380TD. The project was divided into two sub parts; one concerning the design of the cabin and one concerning the engineering. Throughout this rapport you can follow the engineering part of the project. The project has followed a systematic product development process resulting in optimized results for material selection and engineering solutions.

 This report will describe a project between two students from Karlstad University and Markus Norström from Hovercraft solutions. The project aim was to develop a cabin for the hovercraft 380TD. The project was divided into two sub parts; one concerning the design of the cabin and one concerning the engineering. Throughout this rapport you can follow the engineering part of the project. The project has followed a systematic product development process resulting in optimized results for material selection and engineering solutions.

The purpose of this degree-project was to investigate the possibilities for primary air preheating into the two smallest waste incineration boilers of Halmstad Energy and Environment. The investigation is a pre-study which has the primary goal to evaluate technical and financial offers from companies that manufacture primary air preheater, and investigate if it is technically and financially profitable to do a purchase on primary air preheaters in the future.In the pre-study it is proposed that it is most efficient to have individual primary air preheater, one for each incineration boiler and the primary air are also proposed to be preheated by hot water in the pre-study. Further in the pre-study it is proposed that the heat-exchanger should have plain tubes instead of finned tubes, to avoid getting dirty fast. The space in the boiler-room is limited, and therefore the major problem was to fit in the primary air preheaters into the boiler-room. By comparing the different offers from the companies, the result in the pre-study shows that the offer from the company C.A.

The purpose of this degree-project was to investigate the possibilities for primary air preheating into the two smallest waste incineration boilers of Halmstad Energy and Environment. The investigation is a pre-study which has the primary goal to evaluate technical and financial offers from companies that manufacture primary air preheater, and investigate if it is technically and financially profitable to do a purchase on primary air preheaters in the future.In the pre-study it is proposed that it is most efficient to have individual primary air preheater, one for each incineration boiler and the primary air are also proposed to be preheated by hot water in the pre-study. Further in the pre-study it is proposed that the heat-exchanger should have plain tubes instead of finned tubes, to avoid getting dirty fast. The space in the boiler-room is limited, and therefore the major problem was to fit in the primary air preheaters into the boiler-room. By comparing the different offers from the companies, the result in the pre-study shows that the offer from the company C.A.

The purpose of this degree-project was to investigate the possibilities for primary air preheating into the two smallest waste incineration boilers of Halmstad Energy and Environment. The investigation is a pre-study which has the primary goal to evaluate technical and financial offers from companies that manufacture primary air preheater, and investigate if it is technically and financially profitable to do a purchase on primary air preheaters in the future.In the pre-study it is proposed that it is most efficient to have individual primary air preheater, one for each incineration boiler and the primary air are also proposed to be preheated by hot water in the pre-study. Further in the pre-study it is proposed that the heat-exchanger should have plain tubes instead of finned tubes, to avoid getting dirty fast. The space in the boiler-room is limited, and therefore the major problem was to fit in the primary air preheaters into the boiler-room. By comparing the different offers from the companies, the result in the pre-study shows that the offer from the company C.A.

The purpose of this degree-project was to investigate the possibilities for primary air preheating into the two smallest waste incineration boilers of Halmstad Energy and Environment. The investigation is a pre-study which has the primary goal to evaluate technical and financial offers from companies that manufacture primary air preheater, and investigate if it is technically and financially profitable to do a purchase on primary air preheaters in the future.In the pre-study it is proposed that it is most efficient to have individual primary air preheater, one for each incineration boiler and the primary air are also proposed to be preheated by hot water in the pre-study. Further in the pre-study it is proposed that the heat-exchanger should have plain tubes instead of finned tubes, to avoid getting dirty fast. The space in the boiler-room is limited, and therefore the major problem was to fit in the primary air preheaters into the boiler-room. By comparing the different offers from the companies, the result in the pre-study shows that the offer from the company C.A.

The purpose of this degree-project was to investigate the possibilities for primary air preheating into the two smallest waste incineration boilers of Halmstad Energy and Environment. The investigation is a pre-study which has the primary goal to evaluate technical and financial offers from companies that manufacture primary air preheater, and investigate if it is technically and financially profitable to do a purchase on primary air preheaters in the future.In the pre-study it is proposed that it is most efficient to have individual primary air preheater, one for each incineration boiler and the primary air are also proposed to be preheated by hot water in the pre-study. Further in the pre-study it is proposed that the heat-exchanger should have plain tubes instead of finned tubes, to avoid getting dirty fast. The space in the boiler-room is limited, and therefore the major problem was to fit in the primary air preheaters into the boiler-room. By comparing the different offers from the companies, the result in the pre-study shows that the offer from the company C.A.

The purpose of this report is to survey Swedex AB?s production costs and to gather all info into a manageable calculation tool. This was made by time and motion studies, interviews of the personnel. All factors were gathered into an Excel chart.The calculation was made according to an additional-charge-method that was considered to satisfy Swedex AB?s goal.

 This report will describe a project between two students from Karlstad University and Markus Norström from Hovercraft solutions. The project aim was to develop a cabin for the hovercraft 380TD. The project was divided into two sub parts; one concerning the design of the cabin and one concerning the engineering. Throughout this rapport you can follow the engineering part of the project. The project has followed a systematic product development process resulting in optimized results for material selection and engineering solutions.

Saab Aerosystems has a long tradition and a lot of competence in the field of flight simulation. Their ambition to broaden the market horizon has led to a discussion about also selling vehicle simulation solutions, both for military and civilian use.The aim of this thesis is to investigate the driver?s experiences of the accelerations he or she is exposed to whilst driving in rough terrain. The results may be used as a basis for future decisions and can act as a platform for the construction of an effective simulation model.To investigate the driver?s exposure of acceleration, some kind of dynamic simulation is needed.