Our education at Halmstad University was completed with a degree project. Our task was to improve an already existing pneumatic damper to Nederman in Helsingborg. Overall we have made necessary calculations to make the design of the existing damper smaller. When these calculations were done, we moved on with an analysis of the existing damper in order to figure out what improvements could be made on each part of the damper. The result of this project is a smaller and a more supple design of a pneumatic damper. To this we have also created complete drawings, calculated material expenses; we have also created an assembly of a pneumatic damper in Catia v5..

Harmonics are a well-known problem that has to be dealt with in the design of thegenerator. Internationally accepted standards limits the amount of harmonics allowedin the no-load voltage. These limits can be difficult to fulfill with integral slot winding,where the number of slots per pole and phase is an integer. The presence of thedamper winding often makes the problem with harmonics even worse and harmonicswith frequencies of order 6q±1 arise with significant amplitude. How the damperwinding is designed affect the content of harmonics in the no-load voltage and the aimwith these ? has been to investigate in which extent design of the damper windingaffects the contents of harmonics.Simulations with the 2-D finite element method have showed that if the damper barsis centered in the pole shoe, the amplitude of the harmonics of order 6q±1dependsboth on the ratio between the stator slot pitch and damper bars slot pitch and if thedamper bars are connected between the poles or not.If the damper bars is displaced with ¼ stator slot pitch alternately, the amplitude ofthe harmonics of order 6q±1 is reduced and the influence of the ratio between thestator slot pitch and the damper bars slot pitch will vanish.

This master thesis consists of the creation of shock absorber models for percussive rock drills. A model of the rock was also developed. These models were connected to existing models of the rock drill to create a complete simulation of the rock drilling process.When the models had been created the rock model was evaluated by comparison with measured values from lab tests. The verified rock model was then used to evaluate the shock absorber models.Four new shock absorber concepts have been developed. Three of these have been modelled, while the fourth have only been sketched and described.The evaluation of the models showed the following:? Simulations of the single shock absorber don?t correlate to reality very well.

The saw blade producer, Håkansson Sågblad AB, patented in the U.S. a new blade profiledesigned specially to cut fish and meat. The most important advantage of that blade is that its teethare not set, therefore the material lost when cutting is really smaller. The special geometry of thatprofile made that nobody had found a proper way to produce it before.The goal of the outlined work is to develop a machine to produce these new blades in afeasible way.The research approach of the project can roughly be divided into three phases:1.- Invention and development of a proper distribution of blades to produce a big amount ofthem at the same time.2.- Research of the best production process to produce the blades.3.- Main design of the machine to produce the blades.In the Thesis these three points are carefully developed and studied in the form of the startpoint of a really bigger project. Some tests had been done in order to prove all the analytical ideasand the results obtained had been satisfactory enough to give Håkansson the start point of a bigbusiness.

This study presents a methodology that enables the annual average power of a wind turbine to be increased by automatically optimizing it?s airfoil, twist and chord dis- tribution. As a part of the study the software SiteOpt has been developed. This software connects the open source software XFOIL with the blade element momen- tum theory. XFOIL gives lift and drag coefficients which enable the blade element momentum theory to predict the power of a wind turbine at different wind and ro- tational speeds.

This report is the result of a master thesis at the Department of Mechanical Engineering, Division of Industrial and Economical Development, at Linköping University of Technology. The project was carried out on behalf of Fanerami AB, Mjölby and includes 20 weeks of full time schedule work.Cabinets with vertical mounted roller shutters all share the same problem, namely weight balancing. A roller shutter has an equilibrium area where the sum of the different forces acting on the shutter equals zero. As the shutter leaves that area it will pick up speed as it falls towards the bottom. When the shutter hits the bottom of the cabinet there is a potential risk of getting fingers caught and in this project a solution to prevent this from happening was to be presented.In this project, three concepts have been generated with the following different purposes:?In concept 1 the risk of getting any fingers caught when the shutter closes was to be eliminated in an efficient and inexpensive way.?In concept 2 the roller shutter had to be balanced at all time providing the possibility to keep the cabinet open in any position.?The last and most challenging task was to create a remote controlled TV cabinet.

This Master Thesis has been carried out as a new product development project in collaborationwith G-Man Tools AB located in Edsbyn. The purpose of the project was to construct a newpruning saw there the blade is integrateble in the handle, thus a foldable pruning saw.The work has been performed on the occasion of G-Man Tools AB wanted to improve theirproduct range by creating a saw that complement their range of quality saws. They have a similarproduct today, but they do not manufacture this product by them selves and it is not directlytargeted against garden use, which is a disadvantage when it is one of their major markets.Even though almost the entire chain from the requirements of the users to drawings has beentaken into consideration, emphasizes has been put on generating ideas. However the first thingthat was carried out was to establish a productspecifikation from interviews with users and thecompany?s experience.

Detta examensarbete handlar om utveckling och konstruktion av ett spjäll och spjällblad till en plattvärmeväxlare som ingår i Fläkt Woods AB:s produktsortiment.Bakgrunden till utvecklingen berodde på två problem med det nuvarande spjället. Ett problem var att det fanns vissa hygienproblem med befintlig konstruktion som behövde rättas till och ersättas mot en bättre lösning. Detta för att produkten ska kunna certifieras enligt normen VDI 6022. Det andra problemet var att den befintliga konstruktionen kändes gammal och behövde förbättras.Examensarbetet omfattar två stycken huvuddelar/mål. Den första delen är att finna ett material för att kunna täta i spjället på ett effektivt sätt.

The thesis project is accomplished during winter and spring 2008 at Karlstad University at the faculty of technology and science. The tutor at Karlstad University is Nils Hallbäck and the examiner is Hans Johansson. Rolls-Royce at Kristinehamn in Sweden is the initiator for the project. The thesis project title is design of the blade bolt joint on Kamewa CPP. CPP stands for controllable pitch propeller.

Scana-Booforge is a Swedish company which specialize in heat treatment of various metal. The treatments take place in quenching ovens, where fans are used to circulate the hot air. The fans used today do not have a satisfactory lifespan. This thesis aims to develop a new design of the fans for the quenching ovens, and the goal is that the new fans will bring cost savings for Scana-Booforge.The design development process started with mapping out the environment in which the fans operate, and with analysis of the existing fan structure and damages, in order to establish the cause of failure and of short durability. The performance of the fan were also established at this stage.

The division of Electricity at Uppsala University is developing a wave energy converter(WEC) consisting of a linear generator connected to a bouy at the water surfacethrough a wire cable called the connection line.During extreme conditions, the wave power plant will experience forces up to 500kN, which lead to unnecessary wear and will ultimately cause the failure of theconverter. To prevent this there is a need for a damper.The wave energy converter works at a maximum efficiency when the translator?sare centered with respect to the stator. Due to tidal movements the position of thetranslator can deviate. There for a mechanical divice that will compensate for this isneeded.This report describes the further development of an earlier project where a tidalwave compensator for a wave energy converter of Seabased AB was developed.

This rapport handles the presence of two kinds of watermills in the Swedish landscape. The first is a small type with a horizontal shovel blade and the other a bigger kind with a vertical standing shovel scoop. The rapport seeks for information of their capacity and how long they existed as flour producing units. A important issue is how small can a brook be and still run a mill. Finally the reasons for their disappearance in one selected parish is shown..

This thesis is based upon the work done at Westinghouse electric company (WEC)inVästerås during the spring semester of 2015 and describes the development of a quickcoupler with associated blade changing tool. These are meant to be used togetherwith a sawing tool that the company uses for the dismantling of nuclear reactors,which is performed under water.The aim of the thesis was to develop a complete manufacturing documentation withdrawings and related CAD models which Westinghouse later can use to manufacturethe tool and the quick coupler. It was also included in the assignment to, if necessary,modify parts of the saw tool to adapt these to the intended blade changing tool.A number of visits to the company's workshop was made during the time to study thesaw that the thesis is based upon. The purpose of these visits was to get a better ideaof the dimensions, construction and the field of use of the saw. On three of thoseoccasions various engineers and consultants accompanied us to discuss possibleproblems with different ideas.This was interspersed with information in the form of literature studies on quickcouplers to create a clearer picture of the nature of the task.When enough information had been gathered a functional analysis was made to dividethe main problem into subthis phase the idea and concept generating process took place.The methods used for this was mainly brain writing and brainstorming.

The big change is a project where I created patterns on fabric. It is a collaborative project with Lotta Niemi. She studied fashion and textile designers and tailors from the Swedish School of Textiles in Borås and University of Technology in Sydney. The collaboration was to create designs on fabric for her upcoming clothing line for women, Fall / Winter 2013. The clothes will be sold online, in stores in Sweden and Japan.For Lotta Niemi?s clothing line, I wanted to create exclusive designs, rich patterns that worked out handmade and digital.

The expansion of the Swedish hydro power has contributed positively to the reduction of the environmental impacts from the fossil fueled power production. In the same time the extensive expansion has been proved to cause negative ecological and local environment impacts of a stream. This, in turn, has been affecting the biodiversity and fish stock negatively, which has been reduced. One of the underlying problems is the lack of possibility for the fish to pass the plants, but it is also directly correlated to the mortality rate of the fish passing through the turbine, which this study is investigating.The mortality rate has been computed for three different locations in Sweden, Untra, Tännfallet and a third one whose location is confidential, and is denoted as Case 1, 2 and 3. The model used to calculate the mortality rate in this investigation is based by existing blade strike models and knowledge and are investigating the death due to mechanical injuries from collision with a runner blade in the turbine.