AbstractThis report intends through a case study to investigate if lightweight concrete isappropriate as main material in the outer wall of a seven storey residential building.A technical design is carried out in accordance with the definitions and requirementsfor passive houses, given by FEBY?s1 ?Demand specification for passive houses?.A literature review is also carried out for a comparison between regular bolt wall andlight weight concrete wall, with a focus on the safety of moisture.The lightweight concrete block used in the report is as a celblock produced by thecompany H+H Sweden AB.The methods used have resulted in compliance with requirements andrecommendations from authorities. Calculations of energy, noise and moisture riskassessment has been carried out.The work has resulted in the conclusion that the lightweight concrete itself is notable to isolate in the extent necessary to obtain chosen U-value of 0,1 W/m2 ° C,without getting to thick. Therefore additional insulation is needed. There are fewrelevant reference objects built with only light weight concrete.

AbstractThis report intends through a case study to investigate if lightweight concrete isappropriate as main material in the outer wall of a seven storey residential building.A technical design is carried out in accordance with the definitions and requirementsfor passive houses, given by FEBY?s1 ?Demand specification for passive houses?.A literature review is also carried out for a comparison between regular bolt wall andlight weight concrete wall, with a focus on the safety of moisture.The lightweight concrete block used in the report is as a celblock produced by thecompany H+H Sweden AB.The methods used have resulted in compliance with requirements andrecommendations from authorities. Calculations of energy, noise and moisture riskassessment has been carried out.The work has resulted in the conclusion that the lightweight concrete itself is notable to isolate in the extent necessary to obtain chosen U-value of 0,1 W/m2 ° C,without getting to thick. Therefore additional insulation is needed. There are fewrelevant reference objects built with only light weight concrete.

The background to this thesis is that we know very little about lesbian and bisexual women's sexual health in Sweden, particularly in relation to sexually transmitted infections (STI) and their transmissions. An internet-based questionnaire with self-selected participants targeted to the group WSW (Women who have Sex with Women) has been implemented. An international survey on the subject shows that the WSW has sexually transmitted infections. This is also in line with the results in this study. The most common sexually transmitted infection in the survey is chlamydia which 12.3 percent have had.

This study describes what impact activity within Wifstas, Matfors,Grönstas and Nolbys water protection areas have on the quality of the drinkingwater. It considers the use of the area, environmentally dangerous activitiesin the past and present, the geology?s part, what harm hydroelectric power damsmay cause if they break and how climate change might affect the area in thefuture. It also takes into consideration activities outside the waterprotection areas which might have a suspected impact on the water quality. Theresults of the study are that pollution from infrastructure such as roads, orwastewater from treatment plants may cause occasional contamination of thedrinking water, foremost due to flooding.

In my essay I'm studying what aspects of the school environment that influences the pupils experience of safety and what aspects that strengthens the experience of safety. I'm introducing three different dilemmas from three different places in the school environment. The three dilemmas have that in common that they focus on safety. I'm introducing the after-school centre commission according to the National Agency for Education, presenting results and theories from various researchers and authors about how you can work with safety regarding children's development and learning. My conclusion is that safety is a very important aspect when it comes to learning and for the overall development of children.

This report provides a comparison between the products cellular concrete, foam concrete and LECA concrete. The questions to be answered during the work is how the cellular concrete stands up in cost terms to the existing competitors on the market, how the concrete products differ in design work, and in which situations the concrete varieties are preferred to use.Cellular concrete is a variant of ordinary concrete, with the difference that the ballast is exchanged from stone materials to expanded polystyrene beads (EPS). This substitution gives a product with higher insulation values but lower weight than ordinary concrete.The work was carried out by designing a survey which was sent to two hundred randomly chosen companies across Sweden, to see the building industry?s opinion of the product cellular concrete. The survey showed that cellular concrete was equals its competitors in terms of price, while the product was said to be more flexible, quicker and easier to cast.Then some of the companies, who participated in the survey, were interviewed to see more carefully, how the price, the workmanship and the time for casting and dehydration differed between the products.

Safety in the construction industry has become a question of top priority in recent years. Despite a massive investment of time, money and knowledge, the occur-rence of fatal accidents in Sweden alone is around one a month.The purpose of this study is therefore to improve the safety on the construction site. By an examination of the role of the safety agents and their cooperation with the construction workers and supervisors as well as examine how safety agents can improve safety on the construction site, which is the goal of the study.Four questions were formulated based on the purpose and the goal of the study.The methods used to answer the questions were a questionnaire survey, multiple interviews, a literature review and a document analysis.The report describes the safety agent?s role as a complex one with many different tasks. The role of the safety agents is regulated in the health and safety law, but it can sometimes be difficult to interpret and the agents can therefore interpret their role differently.

Municipal safety work is an issue frequently discussed. The new legislation about accident prevention obeys the Swedish municipality to present an action program for accident prevention. In Borlänge municipality there has been no sanctioned proposal for a program. This report presents the problems found and gives proposals for improvements in the future safety work. The guiding words should be unambiguousness, able to control and not too complicated.

Regulation of rivers by dams and reservoirs is a good example where anthropogenic impact could be considerable both in the local environment, but also has major implications upstream and downstream. This study was accomplished as a literature study of the river Nile, which is extremely important for water supply. The purpose of this study was to investigate the consequences of the construction of the Aswan High Dam, to obtain a consistent flow for water supply, irrigation and power generation in Egypt. Since Egypt has a very hot and dry climate large amounts of water in reservoir is lost to the Nubian aquifer system and by evaporation. The consequences from constructing the dam are considerable.

Fall accidents are a big problem in the construction industry today and stand forapproximately 23% of all accidents. Skanska is a construction company that has avision toachieve zero accidents. Eliminating fall accidents is one step on the way towards theirvision. The state of Skanskas fall safety has been analyzed in this thesis to show whichimprovements are possible in fall safety.A literature study has been performed in which Arbetsmiljöverkets (The Swedishwork environment authority?s) laws and rules, together with Skanskas own rules havebeen studied.

A renewed application for environmental permit for the Hovgården landfill in Uppsala shall be submitted before December 2004, therefore the municipality of Uppsala needs improved knowledge of the contents, mostly organic compounds in the leachate and they also want to find a method to minimize the emissions of these compounds. The purpose of this study was to find a practical and economical method based on chemical oxidation using oxidants. The oxidants investigated are Fenton's reagent, hydrogen peroxide, Oxypro, potassium permanganate and potassium persulfate. The study was made on untreated leachate and leachate that has been treated in an aerated dam followed by sedimentation dams collected from the Hovgården landfill, and alson on sludge water from sludge storage cells. The effects of the five oxidants have been established by analysing the UV absorbance at the wavelengths 253,7 nm and 260,0 nm at different pH values. The UV absorbance was used to indicate the amount of aromatic hydrocarbons in the water. Also analyses of iron and manganese were done after the experiments with potassium permanganate, hydrogen peroxide and Fenton's reagent.

The accident frequency in the construction industry has shown a downward trend every year but this trend was broken 2010th. It is often lack of precautionary measures within work environment and safety that is the cause of accidents. The big construction companies understand the importance of precautionary measures within work environment and safety, as they spend a lot of money and time on that matter. By examining the work environment and the safety of the small construction companies you can see how they work. The report will presents how these small companies work with work environment and safety, and also how they follow the safety instructions that are available and how they make use of safety equipment.

In Sweden there are currently two separate guidelines you may use whenperforming calculations on frameworks, BKR and the Eurocodes. Although at theend of 2010 you are not allowed to use BKR any longer and only the Eurocodeswill be viable. The aim of this thesis is to explain how the Eurocodes and EKS work and alsohow they compare to the current guideline BKR. Similarities and differencesbetween these guidelines are also discussed so that the reader will get a betterunderstanding of how the Eurocodes are applied. The areas discussed are asfollows:Principles and adviceSafety ClassesSymbols and IndexesLifespanLoads and partial coefficientThe thesis also deals with the impact that this transition into a new guideline willhave on corporations, guideline costs, education and computer software. As anexample a rough estimate on what costs this transition will create on a companywith 20 employees is also included. Calculations have been performed in order to investigate how the design valuesdiffer between the two guidelines, the Eurocodes and BKR.

This diploma work was conducted in collaboration with the Swedish civil engineeringconstruction company Skanska Construction in Stockholm. Their interest is todevelop a number of type approved form constructions which can be used during theconstruction of concrete walls. Skanska focuses on improving safety on their projectsand both supervisors and workers have a need for approved form constructions inthe current situation.The study is focused on safety and the purpose is to facilitate the preparation beforethe form work can begin. By studying the literature of the subject and conductinterviews with employees at Skanska Construction, the understanding of the issueand knowledge will be increased.Literature studies, interviews together with production and design have been thebasis for a successful study. The work has resulted in three types of approved formconstructions to Skanska Construction and the drawings can be used of employees atthe company.

Concrete is a very common construction material. It´s characteristics are strength, durability and formablility. Superplasticizer is a common admixture, which changes the properties of concrete. Today (spring 2007) there are no certian mathematical methods to calculate the required percentage of this admixture needed to give the necessary set slump flow in the overall concrete recipe. Concrete batching companies must therefor experiment with different amount of superplasticizer in order to meet the specified slump and strength. The purpose og this report is to investigate if any mathematical relation can be established between the amount of superplasticizer used and the slump flow achieved. After carrying out some practical experiments using four different superplasticizers a direct relationship can be establish between the percentage of admixture used and the slump/flowability achieved. Unfortunatly at present due to the numerous variables, the calculation of mathematical formula can not be achieved..