The thesis project is accomplished during winter and spring 2008 at Karlstad University at the faculty of technology and science. The tutor at Karlstad University is Nils Hallbäck and the examiner is Hans Johansson. Rolls-Royce at Kristinehamn in Sweden is the initiator for the project. The thesis project title is design of the blade bolt joint on Kamewa CPP. CPP stands for controllable pitch propeller.

The design regulations of Boverket (BKR) have long been the mandatory standard for construction design in Sweden. However from the end of the year 2010, the BKR will be replaced by the European standard Eurocode (EC). The transition to EC has been delayed and it is not until the second of May 2011 that the use of EC will be mandatory. Because EC and BKR differ from each other it is highly interesting to investigate and explain these differences.The purpose of the thesis is to compare the two standards and investigate how they give different results or not for the dimensioning of structures of steel with associated loads. The current project HVC (Pets Science Center) in Uppsala is used as a model for the design of the steel structure used in this study.

Introduction: Dolomite AB was in need of a dummy arm for crutch testing, to complement their existing test capabilities. Background: A large number of people need crutches on a daily basis. For them it is essential that their crutches do not fail. ISO (the International Organization for Standardization) conducts ongoing work to guarantee the durability and function of e.g. crutches.

Mechanical relays are more and more being replaced with semiconductortechnology. In this thesis it is investigated if and how the larger loads couldbe controlled by transistors. The main part of this work aims to create andverify a solution that can control the starter motor, as well as protect it incase of any failure. The different malfunctions that the solution protectsagainst is high current, too high peak current, low current, maximum cranktime and minimum cool off time. The timers also protect indirectly againstoverheating of the starter engine.The transistors used are BTS555, from Infineon.

When designing roads it?s important to knowwhat loads will bedriven on it. The axles on heavy vehicles can either have super single tires ordual tires which, according to studies, damage the roads differently. The SwedishTransport Administration is developing an understanding for the character ofthese different kinds of axle and tire types on the loads induced on Swedishroads. In this thesis a field study was conducted to determine the distributionbetween axles with super single tires and axles with dual tires on heavy vehicles.A highway, a country road and a national road were investigated during thestudy.

Denna rapport är en del av ett examensarbete på avdelningen för "Byggteknik och design" med inriktning "husbyggnad, projektering och konstruktion" på Kungliga Tekniska högskolan i Stockholm, Sverige.Rapporten handlar om byggandet av ett tak för en skolbyggnad i byn Lwengo Basilla som ligger i sydöstra delarna av Demokratiska republiken Kongo. Skolprojektet finansieras av en ideell organisation i Sverige som heter "Elikia na Biso" och leds av Miza Landström. Designen och konstruktionen av skolan har tagits fram med hjälp av studenter från olika avdelningar inom Kungliga Tekniska högskolan (KTH). En grupp studenter från KTH hjälpte till att lägga grunden och väggarna i skolan. Nästa grupp av studenter skickades för att hjälpa till med byggandet av skolans tak.Denna rapport fokuserar på att dimensionera och konstruera taket på skolan med hjälp av lokala material på ett effektivt sätt.

This degree project was conducted in collaboration with Gremo AB located in Ätran.The aim of the project was to develop a solution to secure quality and to help assemblingthe locknut holding the vertical hinge on the harvesters and foresters from Gremo.At this time the nut is assembled manually by the aid of an overhead crane. The nut istightened differently from time to time, and there was no specified torque to which it istightened. Another present problem was the locking washer which sometimes getsdamaged during assembly, when this happens the procedure has to be started over fromthe beginning. The current assembly procedure is very time consuming and lengthy forthe employees.Our task was to design a machine that could tighten the nut to a specified torque with amargin of error of ± 3%. The assembly procedure will be held simple and the timerequired at a minimum.The project started by developing several principle solutions, the one solution that bestmatched our specifications were developed to a primary solution.Today we have started manufacturing and assembling our prototype.

In this work, a method was developed and evaluated for calculating the life of welds under the influence of fatigue loads from a vibration environment. Typically, a shaker table is used for testing a component against vibration loads. The shaker table creates a vibration environment that is defined in the frequency domain by a power spectrum.Similarly, a virtual vibration table can be used to calculate the same type of load environment, which can then be used to calculate the expected lifetime. The benefit of this method is that it can be used in design, as well as in simulation of tests before physical verification tests are carried out.Today there are methods for calculating fatigue life of non-welded base material, but since many components contain welded joints, there is a need to apply this method to those types as well. To achieve this, the thesis combines two different areas, which together provide a method for fatigue assessment of welds using a virtual shaker table.The methodology is carried out by modeling the component, and its welded joints, in a finite element program.

Transmission of reactive power is well known to cause active power losses. Thus, newcomponents who can help minimizing these expensive reactive power flows are ofgreat interest to the power distribution companies. ABB Corporate Research hasdeveloped the first electronic power breaker. One possible application for thisbreaker is transient-free switching of capacitor banks. This could prove a usefuldistribution voltage complement to the switch-sync technique, mainly applied to transmissionvoltage level.

Today?s climate changes will probably give rise to precipitation in Sweden, which will cause more floods in Swedish rivers. Many of the Swedish rivers are regulated and have lots of hydro-electro power plants. Higher floods in the rivers will give greater water loads on the dams, which mean that a higher discharge through the sluice gates and in the spillway channels is needed. High discharge of water in a spillway channel can create scour of the material in the channel.

I?ve tried to find the most effective and cost effective way to harvest straw for energy recovery.You can choose between round bales and big square bales. Square bales are the cheapest way to produce straw for fuel recovery because you can optimize the length of the bales so they fit the transportation equipment.In the Malmö area the average days of harvesting hay is 55. The effectively of transportation depends mostly of the speed, the distance and density of the bales. To increase the capacity of bale transportation larger loads and higher density of the bales is necessary.

The automotive industry is increasingly studying lightweight solution in their designs, also rational production and low costs in materials and manufacturing methods are of great interest. This thesis consisted in the practical evaluation of anchors for sandwich panels. The object was to study loads of shearing and pull out of the plane. The experiments were carried out on panels made up of 1mm aluminium coatings and 50mm extruded polystyrene (XPS) at its core. As the fasteners used simple methods such as blind rivets, screw and glue.

The government regulations for energy use in buildings will be tightened in the future. At the same time the interest in environmental classifications and certifications of buildings is increasing. This has meant a new situation for solar energy. The designs of solar heating systems are often based on experience and/or rules of thumb, rather than calculations and simulations. This thesis examines whether simulation tools, in this case Polysun, are useful in this work.

In recent time, agile methods have been devoted much attention, and the concept is widely used in the IT industry in particular. An increasing number of companies are interested in this way of working. The following report is the result of a study on the ability to create value for customers in business development through the use of agile methods. We ask what the advantages and limitations of agile methods are in the creation of customer value. Grounded Theory and an initial literature review was used to answer this question.

Before the European construction standards were introduced in January 2011, it was mainly themethod in BBK04 that was used for calculating punching capacity in concrete structures, and in lesscommon cases the method in BHB. The method of BBK04 is easy to use and have had the samestructure since the first was published in 1979. The Concrete handbook method (BHB) where usuallyonly used when a higher punching capacity was needed and the cross-sectional height where fixed,calculations using this method entails more work, but will in return usually give a higher capacity. Italso allows the use of shear reinforcement to increase the cross-section capacity. The method ofcalculating punching shear in EC2 differs largely from the methods of BBK04 and BHB.