Many companies do not register all the stops that occur in a production plant, it often takes longer to report than to fix the problem. If no problems are registered, you cannot trace where the problems arise.This master thesis was performed at AcobiaFLUX and they have noticed an increased demand from their customers to trace problems raised in their processes. The aim of the thesis was to find out how a tool to monitor a process best could be developed. Then the most essential from the theoretical base was developed into a useful tool for operators. For the operators to know if the process utilizes the full capacity of a process, the tool presents a measure of the Overall Equipment Efficiency, OEE.

Micro-power wind energy convertors have recently increased in popularity. The reasons for this are among other things the increasing cost of electric energy and enviromental concern.In this thesis the connection of these micro-power wind energy convertors to the utility network is discussed. Electric standards for the connection of small production units is presented. Finally some calculations and measurements of electric quality are also presented. The utility network used in the calculations is part of Halmstad Energi och Miljö network..

Drinking water from drilled wells has a high content of iron and other minerals in many places in Sweden. Questions about the association between the quality of drinking water and the health of dairy cows are regulary asked both by advisers and dairy farmers. There are so far not many studies published about the relevance for high iron content in water and dairy cow health and production. Therefore, the aim of this study was to investigate if there is a connection between the iron content in water and the health of dairy cows. Initially a literature study was made about iron and it´s function in ruminants.

The purpose of this master thesis is to investigate different types of measures for making buildings more energy efficient and to estimate their profitability. The calculations were performed with the building simulation program VIP+ and the evaluation of the profitability with the life cycle cost method. Furthermore, it was examined how losses in the distribution of secondary systems of district heating can be avoided. Options to replace district heating with a local district heating system based on bio-energy have been investigated. The possibilities of achieving more efficient thermal energy consumption and production for the chosen estate were also examined.The object of the study has been a residential estate with 133 detached houses in Uppsala, built in 1974.

The task was to deliver a solution that could be implemented in today?s production of the FH truck. To make the project successful it was most important that the end result had a high maturity level. For that reason an analysis of ergonomic, laws and regulations, and possible materials where conducted. To show that this project is profitable and can be realized a ruff cost estimated of material and tools is added to the research.

This paper is about the new methods and metrics used in industry and business today striving for better revenues and larger market shares. It investigates the relations between the old fordistic and tayloristic way of manufacturing and compares it to the models used in industry today for being competitive, seeking to please customers and becoming more flexible. More specific the paper is about if Six Sigma and lean production are the key for succeeding these days. SKF:s factory in Gothenburg and other companies will make an example for how these methods are used in practice.The aim is to try to answer if these systems with inherited tools and methods are the right way to get the flexibility that is needed for being able to deliver the right goods to customers and market. For a company to be flexible decisions must be made fast and needed changes must be able to be done easy and without too large costs and investments.

Scana-Booforge is a Swedish company which specialize in heat treatment of various metal. The treatments take place in quenching ovens, where fans are used to circulate the hot air. The fans used today do not have a satisfactory lifespan. This thesis aims to develop a new design of the fans for the quenching ovens, and the goal is that the new fans will bring cost savings for Scana-Booforge.The design development process started with mapping out the environment in which the fans operate, and with analysis of the existing fan structure and damages, in order to establish the cause of failure and of short durability. The performance of the fan were also established at this stage.

The purpose of this report was to compare Lilluns egg production with other Swedish egg producers based on the flow of nutrients (nitrogen, phosphorus and potassium) in the egg production systems. The main focus in the report was the utilization rate of the forage and the excess of nutrients per kg egg. Additionally, the purpose was to identify the environmental impact from Lilluns egg production and compare the results with other egg producers. The inflow of nutrients associated with forage and poultry was compared with the nutrients that were exported from the production. All of the egg producers in this study had an excess of nutrients.

Detta examensarbete handlar ?Verklighetstrogen Effektskomposition?. Målet med arbetet är att undersöka och utnyttja alla de olika aspekterna som gör att en film med specialeffekter känns så verklighetstrogen som möjligt. Arbetet handlar om de olika delarna i en filmproduktionsfas så som pre-production,production och post-production. Filmen som skapas är en specialeffektsbaserad hemmavideo som har som syfte att vara så chockande som möjligt i förhållande till vad man förväntar sig när man börjar kolla.

Sustainable beef and milk consumption. The consumption of beef and dairy products in Sweden is high. A lot of greenhouse gases are emitted from the production of these products. The production of beef in Sweden has decreased but the import has increased. The number of dairy cows has decreased while beef-production with suckler-cows has increased in Sweden.

When a person arrives at the emergency ward at the Uppsala University Hospital with his or her symptoms he or she explains the problems and then a priority process starts. The staff evaluate at which emergency level the patient is located in a model called Triage. The Triage model helps to decide the priority need and is based upon templates which point out in which of the 5 categories a patient is to be placed, to eliminate any future risk regarding his or her health. A lower triage level means lower priority but implies better health when the evaluation takes place. To obtain optimal effect of the Triage model the evaluation of symptoms must be reproducible so that patients with the same symptoms are placed at the same triage level regardless of whom among the staff conducts the evaluation. The purpose of the study was to see if the resources are allocated based on priority level of the patients.

Responsible production is a subject of increasing importance for companies toadopt and communicate to their environment and many companies choose to implementenvironmental ? and ethic considerations into their brand strategy. There is, however, adividing line between companies according to what extent they choose to implementresponsible production into their brand strategy and to which extent they choose tocommunicate it to their stakeholders and surroundings. It is the hypothesis about a dividingline that is the foundation for this essay and something we believed could be interesting forfurther analysis.The purpose of our essay is to find out how the brand strategy of a company is affected by theresponsible production and in what extent they communicate it to their environment. Byanswering those questions we hope to find out why some companies communicateresponsible production more actively than others.We have conducted in-depth interviews with the Swedish clothing companies; MariaWesterlind, Zion and Dem Collective and we have through our analysis reached interestingconclusions.

This study is preformed at Westbaltic Components placed in Töcksfors Sweden. Themain target in this study is to make one of the company?s assembly lines better andmore effective. The assembly line constructs vending machines for different stores allover Europe.It will contain tobacco, snuff, cigarettes and shaving blades and many more similarproducts.The first step in our study is to locate the daily problems and find out a good way toreduce them and make them disappear. A good way to do this job easier was toconstruct a visualizing board.

The purpose of this study is to increase the understanding of activities, flows and waste in a company's production process. By performing a value stream analysis, non-value adding activities are identified in a production process and then the suggested improvements that can reduce lead times will be stated. The value-stream mapping identifies the flow of information and the flow of material in a production process and this provides the basis for the identification of non-value adding activities.We conducted the study at Lammhults Möbel AB in Lammhult Sweden, where the production flow of Spira-21 has been investigated. This to identify any non-value adding activities that affect the flow negative and consumes time and money in a non-value adding way.A reasonable approach for the project was taken by studying the methodologies and theories. We conducted interviews and site surveys at Lammhults Möbel AB where the flow of information and material in the production process were investigated.

This report is the result of a thesis work carried out on the Risifrutti production at the company Procordia Food AB. The thesis is at a master level and is the final work for the author to receive a Master of Science in Innovative production at Mälardalen University. The thesis comprises 30 credits and has lasted for 18 weeks. The thesis is mainly a research on whether it is possible to perform an Environmental Value Stream Map (E-VSM) in a food processing industry and an evaluation if the tools E-VSM and Green Performance Map (GPM) are useful in this type of industry. An extra part to this research is to use the results from the E-VSM and give Procordia Food AB information on improvement potentials in the Risifrutti production. The author has found it difficult to collect some of the quantitative data to the E-VSM, mainly regarding energy, but by using the Value Stream Mapping (VSM) tool and other Lean tools the author was able to identify and quantify several wastes in the Risifrutti production. Recommendations for improvements based on these wastes have been given to the company. In the research part of this report the utility of the Value Stream Map, Environmental Value Stream Map and Green Performance Map in a food processing industry have been analyzed. The author has found that the Value Stream Map has been a useful tool since waste and unevenness in the tact of the production has been identified. The Environmental Value Stream Map and the Green Performance Map are also great tools when a company wants to analyze their environmental impact and then invest in environmental improvements. However, no profound energy analyzes has been done in the Risifrutti production because of the lack of energy meters for steam, electricity and compressed air in the production lines..