The climate changes that are occuring in the world have resulted in that the EU callingfor a 20 % reduction in energy consumption to the year 2020, to reach that goal theEU want the public sector to go forth as a good example. Västfastigheter owns andmanage the hospital buildings in the Västra Götaland region. To be able to reducetheir energy usage Västfastigheter has hired several consulting firms to chart out theenergy consumption on each hospital building. The biggest energy savings potentialhave been calculated and what the cost will be to perform each action. The energyaudit have been completed and stand as the decision basis for Västfastigheter?s choiceon which action packages that should be implemented.

This final year project is made for Peab Jönköping and its target group is the construction industry. The main focus is the use of unutilized building material in the most economical and environmental-friendly way. Unutilized building material is here defined as material purchased for a construction project that for different reasons not has been used. The most important thing to find out was how much building material considered as being waste is actually useable material, and how much less it costs to use that building material instead of throwing it away.When this information was gathered a proposal on how to efficiently use the unutilized building material instead of wasting it was designed. Costs and incomes were investigated and the proposal suggested a storage area where Peab can store their unused building material.

Introduction: Every year about 450 women in Sweden are diagnosed with cervical cancer, almost 200 die and thousands undergo surgery because of cell changes in the cervix. A HPV infection can lead to cervical cancer and therefor costs for the society. The implementation of a vaccination program against HPV is a way to avoid these costs. Aim: The study aimed to calculate the economic impact of the HPV- vaccination program for children in Sweden through a cost-benefit analysis. Method: In this analysis, status quo was compared with non-administration of the HPV-vaccine for the selected cohort of ten-years-old girls in Sweden.

The purpose of the set of regulations as regards to accounting and auditing within the Union, is primarily to ensure a high quality of the large public companies financial reporting and hence protect the capital market investors. As the set of regulations also applies to the small companies, these are burdened by administrative costs that are disproportionate. To increase the competitiveness of the European companies, the European council has stated that it is essential to reduce the companies? administrative costs. The main principle is that all companies are under an obligation to statutory audit, however Member States may make audit exemptions for small companies.

This thesis work is made by Torbjörn Johansson on Karlstad University for Uddeholms AB. The assignment in this thesis work was to investigate tough cutting in three different tool steels: Vanadis 4 Extra, Vancron 40 and Sverker 21. The research was to compare the wear of the tool after cutting in each one of the tool steel alloys. The research was also made to see if the tool cutting in Vancron 40 has a better wear than the tool cutting in Vanadis 4 Extra and also compare the results with Sverker 21. All three of these alloys are a part of Uddeholms AB:s range of products, and is used in applications like forming tools and knife tools. Vancron 40 is a powder steel with a very good combination of mechanical properties like ductility, adhesive strength and hardness.

This study investigated the performance and cost of scarification with a tractormounted excavator. Due to variations in terrain conditions the performance variedbetween 0.08 and 0.11 ha/E15h and, with a machine cost of 366 SEK/h, the cost ofscarification varied between 3 330 and 4 750 SEK/ha..

The purpose of this essay is to identify costs for providing First-line and Second-line support, and then allocate these cost to different goods and services (cost objects) being supported. The thesis also intends to improve the overall cost awareness in IT settings..

Scana-Booforge is a Swedish company which specialize in heat treatment of various metal. The treatments take place in quenching ovens, where fans are used to circulate the hot air. The fans used today do not have a satisfactory lifespan. This thesis aims to develop a new design of the fans for the quenching ovens, and the goal is that the new fans will bring Cost savings for Scana-Booforge.The design development process started with mapping out the environment in which the fans operate, and with analysis of the existing fan structure and damages, in order to establish the cause of failure and of short durability. The performance of the fan were also established at this stage.

Today's high oil prices and more stringent environmental requirements have led to that manufacturers of mobile construction equipment try to make their products more energy efficient. With this in mind a project about hybridization of hydraulic systems has been formed. The purpose of this project was to analyze the savings that can be achieved by hybridization of hydraulic systems. A reach stacker truck (Kalmar DRD450-80S4XS) were simulated in some load cases with conventional hydraulic systems and with three types of hybridized hydraulic systems. Different parts of the hydraulic systems were also analyzed separately.

Drain water heat recovery is an uncommon measure in multi-unit residential buildings. There istechnology available for the purpose but the knowing and experience of the heat recovery systems islittle. The purpose of this thesis is to evaluate the future potential of drain water heat recovery inmulti-unit residential buildings.A major part of the multi-unit residential buildings in Sweden were built during modernismen andrekordåren (1940?1975). Many of the buildings have worn out drain and water supply systems andmany are in need of a general refurbishment.

Fuel wood is currently the third largest assortment from the forest in Sweden after pulpwood and lumber. Branches and tops i.e. logging residues are one of the assortments of fuel wood which is a common by-product after harvesting nowadays. The way to utilize, disintegrate and transport the logging residues varies between northern and southern Sweden. Branches and tops are collected throughout the year at appropriate stands, but are consumed mainly wintertime.

The guest harbor on Utö, Utö Gästhamn, is currently using electricity for heating all of the water used in the showers and taps. Because of the large amount of visitors, especially during the summer months, the hot water usage gets very high and that is also the case for the electrical bills. During the year of 2011 the cost of electricity for Utö Gästhamn reached a total of 257 500 kr. Out of these 257 500 kr approximately 142 000 kr, 55 % of the total cost, were because of the water heating.The report is the result of a cooperation with Skärgårdsstiftelsen, the Green Islands-project and Utö Gästhamn where the mutual goal is to dimension a solar energy system, to promote the sustainable development.Initially the different techniques for the solar energy system are researched. The techniques are plane solar collectors, evacuated tube collectors, pool collectors and photovoltaic cells.

Upon marketing the system in Europe and the USA Cost savings generated from reduced work force have been prevailing. Since the cost of labour is much lower in the Asia Pacific region other factors have to be stressed. The parameters of flexibility and quality assurance may however cover any initial investment in a production system. Our purpose is to value flexibility and quality in a manufacturing context, applied to DAS, in order to use it in investment calculations. In order to make an adequate estimation of different companies, due to problems associated with acquiring correct figures, the Key Success Factors needs to be examined so that the gathering of numbers can be conducted with more focus.

This thesis describes how a cost reduction project was done on the Packsize ondemand packing machine EM7. The cost reduction was achieved by making minorredesigns of the EM7.The project began by studying the EM7´s structure and function by working on itsassembly line. A short literature study on the subject Design for Manufacturing wasalso done.By working on the assembly line and by speaking with staff from production anddevelopment departments, a number of ideas for reducing manufacturing costs arose.Estimations of the potential cost reduction size for each proposal were done incollaboration with vendors and the purchasing department. Based on the size of the cost reduction, technical risk, impact on the assembly lineand the development time the various proposals were ranked. The two highestranked proposals were selected for further development towards finished solutions.One of the ideas that were selected to develop in to a finished solution meant thatsome of the pneumatic valves were replaced with others.

An energy calculation model for Swedish houses   that is fast, flexible and user-friendly has been developed within the   framework of this thesis.  The model   also provides a set of actions which may be investigated in the model based   on savings and payback period. Energy use in a house depends on the technical   conditions, such as building envelope and heating systems, which outdoor   climate the house is exposed to and who lives in the house. Energy use for a   house can be divided into heating, hot water and household electricity. There   are several methods to calculate the energy use of a house. This report   summarizes the methods that may be suitable for a fast and user-friendly   calculation model.