The aim of this report was to investigate the economy of passive houses. The work was focused on economy in total and on the economy of different components such as windows, insulation, heat exchanger and the air tightness of the climate shell. No attention was paid on the comfort factor or to the impacts on the environment.Two houses, aspiring to be passive were chosen; A big one and a small one. Hence, comparisons considering the size of the building have been possible to do as well.The comparisons were made by calculating ?break even? between two concepts; passive and BBR- concept.

Because of increasing demand of power on Malmbanan the capacity of the existing wires which supply the trains must be increased. This increases the stress on the existing poles and for this reason the system for supplying the loads along the railway is to be removed from the poles and be replaced by some other system. This thesis is a study on a two-level low voltage (1 kV and 0.4 kV) electrical system with the aim to investigate if it can be an alternative to the system used today taking into account the voltages, fault currents and costs.In this thesis the following tasks have been performed:? Gathering of data? Description of basic theory? Loadow and fault current calculations of the system with MATLAB? Life Cycle Cost estimate of the system? Analysis and conclusions from the resultsThe results show that the new system can be an alternative to replace today's system. The simulations and calculations show that the voltage drop is at an acceptable level and that the fault currents are large enough to supply a safe disconnection if a fault occurs at the far end of the system..

In this thesis you will be able tofollow the design work of a drumtest. A tool that by having a rotatingdrum with equally positioned obstacleswill simulate the conditions a mountainbike rim will pass through.Initially there is a specification ofsome parameters and requirements thatthe design had to fulfill. There is alsosome brief background information aboutwhy a drum test is required for abicycle rim manufacturers and about thecompany Innolite Design AB that thisthesis is done for. After that itfollows an extract from conceptgeneration with the chosen concepts andsolutions but also some of the conceptsthat were not chosen.The thesis also contain a part where thereader cangain a deeper understanding of how thedesign works as well as some moredetailed facts about how the choice ofmaterials, their thicknesses, etc. havebeen made.

The current situation for Swedish grain farmers facing a situation with decreasing profitability makes it necessary for the farmers to find ways of increasing the margins in their grain growing. Decreasing profitabilities along with Lantmännens closing of grain elevators contribute to the necessity for farmers to invest in grain storing and drying at the farm. By investing in capacity for drying and storage of grain on the farm it is possible to recieve a higher price on the grain sold due to the possibility to sell when the price is higher compared to the harvesting season. An investment in grain drying and storage with a relatively low investment cost that recently has appeared on the Swedish market is the grain stir drying system. This study contains a comparison of an investment in a grain stir drying system where the grain is dried and stored in the same silo and a conventional drying and storage system.

Many corporations turn to IT-outsourcing to focus more on their core competence or to cut the IT-budget. There is one caveat, the costs presented at a first glance does not always present the entire truth. Instead the costs run deeper and so-called hidden costs exist beyond the contractual cost. Reducing these hidden costs may very well be crucial to the entire IT-outsourcing endeavor. However many firms are not aware of these costs and as such they have a reduced chance of success.

Abstract    Objective: The aim of the present study was to investigate if inclinometer estimates of arm posture during paper mill work differed between periods of different arm visibility. The aim was also to identify strategies for and difficulties in assessing body-visibility on video. Methods: The study consisted of two parts, where part 1 aimed to investigate the validity of observation-based assessment of arm posture during paper mill work. Study 2 was a survey among people with experience in assessing the posture of paper mill workers from video. Results: The total time for the right upper arm visibility indicates that it was on average visible in 54%, partly visible 15 %  and not visible 31%.

The Swedish bank Handelsbanken has, according to their own way of measuring, been more successful than a weighted average of their competitors during the last 38 years. They have also handled the recent financial crisis, as well as the one in the 1990´s, better than most other banks. This paper studies their management control system at branch level in order to identify the controls which have been enforced to ensure that a low risk level is retained in the lending. The controls that have been identified are; (1) A decentralized organization with the offices as profit centers where the manager has restrictions regarding risk level and the results are measured as K/I (cost/revenue). (2) The absence of bonuses and individual follow-up regarding performance measurement.

The aim of this report was to do a case study at a geothermal heating system which has been in operation for about 5 years, and study if its performance has changed during this period of time. A literature study about the processes involved was also done in purpose of background knowledge.The tenant-owner?s association Duvan at Petterslundsgatan in Uppsala installed year 1999-2000 a geothermal heating system. The purpose of this installation was that they hoped it would lead to a smaller usage of district heating which would lead to a reduction of the heating expenses for their buildings. The geothermal heating system consists of 19 energy wells and 4 geothermal heat pumps, and it is one of the first systems of that size in the region of Uppsala.

Stump wood was used between 1850 and 1950 for production of tar and as firewood. In the 1950s the use decreased because of the introduction of the cheap fossil oil. In the 1970s stump wood became an interesting issue again as a raw material for the pulp industry. Stump lifting has today become a possible source for bioenergy. The objectives with this study were to investigate the productivity of stump lifting and stump extraction, and to analyse the economy.

Sigill Quality Systems has been certifying beef since the autumn of 2006 using the brand name label Swedish Sigill. IP Sigill (the certifying system for integrated production) encompasses the values: animal ethics, food safety, free range and environmental concerns. Product quality is not yet one of these values, and there is a variation in the quality of Swedish beef. Swedish Sigill wanted to investigate the factors that influence product quality, review which of the present regulations that have an influence on product quality and formulate new regulations with the purpose of enhancing the product quality (sensorial, technological and nutritional quality). A survey of quality parameters and factors that influence product quality was done in order to establish a scientific foundation to work from.

Detta arbete presenterar enmatematisk optimeringsmodell gällande val av Prefableverantör för Spinactor ABmed avseende på inköpspris med volymrabatt samt transportkostnad. Utöver dettatillkommer en kvalitativ undersökning om vilka andra kriterier som ärbetydelsefulla vid leverantörsavtal. De viktigaste kriterier applicerades i enegenutvecklad leverantörsvalsmodell som bygger på ramverket ?total cost of ownership?(TCO) där leverantörskriterierna kvantifieras. Utifrån kriterieanalysenframgick att de tre viktigare leverantörskriterierna för Spinactor AB idagsläget är leveransprecision, kundservice och kommunikation samt ekonomiskstabilitet.Lösningen av optimeringsproblemet genomfördes med två olika metoder,linjärprogrammering samt heltalsprogrammering, där linjärprogrammering vardominerande i lösningstid.

Radio Frequency Identification, RFID, is a convenient way to enable contactless identification which does not require any physical nor optical contact. As with any radio-based communication the signal can be intercepted, thus making the technology vulnerable to several kinds of attacks. Interception of communication is not the only threat. Since RFID tags might contain personal information or information that will grant the owner access to secure areas, skimming and spoofing attacks are also major threats against this technology. In this thesis report,  the perspective of an adversary is portrayed in an RFID-enabled environment by presenting where RFID is used and how it could be abused.

This report shows methods and workflow when exploring the potential to change Outotecs HCD Silver Electrolysis machine to a module type. It?s done as an attempt to lower the workshop and installation costs and to give customer a more accurate prize directly. To do this a concept was produced which was set to a stress test. Additional objectives were to investigate freight and installation procedures, pneumatic connections and to calculate the difference in cost.Once the concept, a reinforced type of the original frame, was chosen stress tests in computer simulations were made and appropriate alterations were made.

In the global and rapidly changing society Environmental scanning is becoming a more and more important tool. Today it is not the availability of information that controls an organizations behavior, but the information that the organization chooses to absorb. This is the case for a multinational cooperation as well as for the local golf club. Swedish golf clubs have during the last 100 years had an amazing development and today there are almost 600 000 registered Swedish golf players. The development has however stopped and even declined some during the last couple of years.

The purpose of this study is from a case study develop a model that aims to cost effectively improve productivity in a manufacturing production process. The study highlights the importance of having knowledge about customer needs and using a holistic process perspective when improving productivity to identify the relations between the process stations and by this find problems that cause waste and losses in productivity. Tools and methods used to make production more efficient such as single minute exchange of die, spaghetti diagram, 5s and master production schedule is presented an applied in the model to see how these effect costs, productivity etc.Maintenance effects on quality and productivity in a manufacturing company will as well be covered in this thesis. The results and conclusions finally reveals how the process improvement tools, maintenance and production planning for example effects each other and why it is important to establish an attitude in the company where continuous process improvement should be emphasized..