The purpose of this thesis has been to build a parameterized model of a prototype motor in the program Solidworks, to use in future optimization of aspects of effectiveness and weight. The result were two models. The first model were one minor part of the whole design in 2D, to be able to optimize and study the minor part with a faster loss simulation. The second model was the whole design in 3D. The whole model were done with the three programs Solidworks, Comsol and Matlab.

This thesis has been a part of Forsmarks Kraftgrupp AB's evaluation of a turbulencemodel used in simulation of turbulent flow called PRNS (Partially Resolved NumericalSimulation). This model has promising properties and may be of use in savingcomputational resources. The purpose of this thesis was to analyze this model andcompare it with industrially applied models such as k-omega SST and LES (Large EddySimulations).PRNS works as a hybrid of the k-omega SST and DNS (Direct Numerical Simulation)where a constant, RCP (Resolution Control Parameter) with a value between 0 and 1are selected. This constant is then used in the calculations and determines thebehavior of the simulation. When RCP is set to zero the equation are the same as fora DNS simulation and when RCP is set to one the equations for k-omega SST issolved.

At the department of Electronic Warfare Assessments at the Swedish Defence Research Agency in Linköping one of the activities is modelling and simulation of the duel between a robot and a target. The aim with this Master's thesis is to develop a simulation model of an hovering helicopter. First a theoretical description of the forces and moments acting on an helicopter is given. Then the equations of motion are derived. These equations are simplified to be valid only for a hovering helicopter and the result is a mathematical model.

The purpose with this paper is that trough a description of the management control at Jitech AB find out if traditional management control have been abandoned for benefit for modern management control and in which extent the transition have happened. Further is the second purpose with this paper to find out which decisions that lies behind the design of the management control and how these are in opposition to with the theory..

This thesis is the result of the author?s interest in music and electronics, namely the design and manufacturing of a stereo sound system with an active crossover. In short it can be stated that an active crossover has many advantages over its traditional passive counterpart. The active design naturally results in a more complex system comprised of a multiple number of components. This report deals with the theoretical aspects of preamplifiers, crossovers and power amplifiers as well as power supply and control.

When driving hard and cornering on a circuit good control of a car?s roll is desired, so the car reaches steady state quickly but yet in a controlled fashion. This control is mainly given by the combination of the cars springs, shock absorbers and anti-roll bars.The aim of this report is to investigate, analyze and measure a Porsche Boxster?s turn in behaviour and roll dynamics as well as with the aid of simulation results give suggestions for improvement of the previous mentioned combination.Two different simulations were made, one based on a simpler model that was based on an evolved version of the bicycle model in Matlab and one was more advanced model in the simulation software rFactor. Measurements of the real car was made using a GPS-based measurement system.

Svenska Kraftnät is (together with the other transmission system operators of the Nordic power system) responsible for keeping balance between the generated and demanded power in the Nordic power system. Spontaneous load variations and system disturbances, however, lead to power imbalance followed by frequency variations. The frequency deviations can be limited to an acceptable level by the spinning reserve, mainly by hydro power control. But there are also other system properties which have a great influence on the frequency and system stability. The frequency and voltage dependence of the loads have a direct influence on the power balance.

A piezoelectric injector was modeled, in this Master Thesis Project which was carried out at Scania CV AB in Södertälje, in GT-Fuel. GT-Fuel is simulation program from Gamma Technology.The simulation model for the piezo injector was divided into a hydro-mechanical system and an electrical system (Piezoelectric element). First the hydro-mechanic model was duplicated from Advance Continuous Simulation Language model (ACSL). The simulation results were then compared to the ACSL, to verify that the hydro-mechanical system was modeled correctly. The simulation results for the electrical model were also compared with a Simulink model.

A key part in the development and verification of digital systems is simulation. But hardware simulators are expensive, and software simulation is not fast enough for designs with a large number of gates. As today?s digital zesigns constantly grow in size (number of gates), and that trend shows no signs to end, faster simulators handling millions of gates are needed. We investigate how to create a software gate-level simulator able to simulate a high number of gates fast.

Fluids are important to the Visual Effects Industry but extremely hard to control and simulate because of the complexity of the governing equations. Fluid solvers can be divided into two categories, those of the Eulerian point of reference and those of the Lagrangian. Both categories have different advantages and weaknesses and hybrid methods are popular. This thesis examines Smoothed Particle Hydrodynamics, a Lagrangian method for physically based uid simulations. To allow the artist the exibility given by shorter simulation times and increased number of iterations, the performance of the solver is key.

In this report I will describe how an art-directed fluid effect for motion picture can be achieved. This effect will be an explosion with a visual style that is congruent with Pixar's movie Up. To begin with I will analyze the visual components that are used in Up and control the fluid simulation to get the desired visual style. I will briefly explain the background of my thesis, why it is interesting to create designed effects and why it is hard to design fluid effects. In the method I will explain my work process and some of the challenges that arises.

The purpose with this paper is that trough a description of the management control at Jitech AB find out if traditional management control have been abandoned for benefit for modern management control and in which extent the transition have happened. Further is the second purpose with this paper to find out which decisions that lies behind the design of the management control and how these are in opposition to with the theory..

Problem: What are the characteristics of Polykemi?s management control system and how is it affected by growth? Purpose: To describe and analyse the management control system of a medium-sized family-owned company from the perspective of Simons? Levers of control. Research design: An abductive, interview-based case study of Polykemi AB. Conclusion: Polykemi?s management control system is primarily a traditional one which is rather strong in terms of Levers of control.

This master thesis was made to validate hydropower models of a turbine governor,Kaplan turbine and a Francis turbine in the power system simulator ARISTO atSvenska Kraftnät. The validation was made in three steps. The first step was to makesure the models was implement correctly in the simulator. The second was tocompare the simulation results from the Kaplan turbine model to data from a realhydropower plant. The comparison was made to see how the models could generatesimulation result that was similar to the reference power station.

Value-at-Risk (VaR) is among financial institutions a commonly used tool for measuring market risk. Several methods to calculate VaR exists and different implementations often results in different VaR forecasts. An interesting implementation is historical simulation, and the purpose of this thesis is to examine whether historical simulation with dynamic volatility updating is useful as a model to calculate VaR and how this differs in regard to type of asset or instrument. To carry out the investigation six different models are implemented, which then are tested for statistical accuracy through Christoffersens test. We find that incorporation of volatility updating into the historical simulation method in many cases improves the model.