As part of an internship at Ericsson, this report was written to enhance the understanding of how it is to develop a system that is well established at the workplace. To improve an already existing system is not always as easy as many developers may think. In this report the pros and cons of developing an already existing system has been researched and analyzed. Do note that the results are only from one development of a specific system and that comparison of other developments has been made from other reports and not from experiencing it firsthand. It was found that the choices made can have an impact on further developing and it is important to write down what has been done.

The use of Power Line Communication, PLC, as a communication solution for Automated Meter Reading, AMR, is popular by utilities in Sweden and other parts of the world due to demands of accurate and fast meter reading. However the use of the electrical grid as a communication medium is complex and sometimes problematic. This report handles some of the issues and problems that are important to understand when using the grid as a communications medium. Focus is mainly on investigating high frequency distortion in the Kristianstad power grid own by C4energi caused by a frequency converter. Measurements on site are done to investigate signal damping in the grid, different configurations for the frequency converter and signal strength of the PLC-system.

The Stradella system on an accordeon is a complicated construction. It has readymade con-nected chords, these are major, minor, seventh and diminished seventh. To reach other vari-ants of chords you have to combine chord/bass buttons. Which advantages and disadvantages do the use of combined chords/bass buttons mean? How is the pedagogic work affected by using the combined chords/bass buttons? I have interviewed four musicians/teachers to learn about this technique.

The majority of all power cuts that affects individuals and communities are caused by earth faults on the power transmission lines at 10kV and 20kV level [1]. If these power cuts could be eliminated, less disturbances and interrupts would lead to large amounts of money savings.Swedish Neutral has developed such a protection system. When an earth fault occurs power is injected into the neutral point of the transformer. The RCC (Residual Current Compensation) protection calculates a compensation current exactly 180 degrees out of phase to the fault current. Doing this, the voltage at the fault location becomes very close to zero, without affecting the power transmission.The protection system can only compensate automatically for the fundamental frequency (50Hz), and manually for the 3rd, 5th, 7th and 9th harmonics.

Two ecological models of nitrogen processes in treatment wetlands have been evaluated and compared. These models have been implemented, simulated, and visualized in the Modelica language. The differences and similarities between the Modelica modeling environment used in this thesis and other environments or tools for ecological modeling have been evaluated. The modeling tools evaluated are PowerSim, Simile, Stella, the MathModelica Model Editor, and WEST. The evaluation and the analysis have been performed using McCall?s factors for software quality (McCall et al, 1977), a correlation analysis and the Constant Comparative Method (Glaser&Strauss, 1999).

This project concentrates on musicians who work in a professional music studio.The task of this project was to design a new headphone system called Foldback system.The advantage of this system is that all involved in a music project could influence their ownlistening during the project. With a couple of adjustments should each and everyone get theirown individual listening from their headphone station.This report shows different methods, theories and results that came along in development ofFoldback system. The project has resulted in a finished product that will be in use atStudiomega..

Competence is a complex concept that encompasses many facets. This study aims fora better understanding of the concept. Many branches of business administration science would benefit from a better understanding of competence and, through that understanding, find solutions where competence is one of many variables. By combining a positivistic and phenomenological approach, this study has created a broader understanding of the concept of competence.The study combines systematic study of the relevant literature with in-depth interviewswith people representing both the employer and the union within the staffing company world.The results show that quantifying competence is a complex and next to impossible task, as it would involve including the whole concept of competence in the calculations. When this is done, the phenomenon itself becomes so complex that it loses its validity.This is why theorists who want to perform this type of calculations put most of the competence complexity in ?the black box?.

The author of this report has created a Web-based invoice system and CRM at therequest of the company Webhouse.se. The purpose of the System is to makeeveryday tasks in the company easier. The system also needed to prevent mistakesand errors by managing orders and invoices.The system has been created with the company?s requests in focus. During thedevelopment of the system information security and interaction design have beenimportant aspects that have been taken into consideration.The system has been created using techniques such as PHP and MYSQL.

This thesis investigates techniques for stealth hydroacoustic communication using spread spectrum. The Swedish naval defense organisations have a vision that all their units should be able to communicate with each other, even between underwater vehicles. But the properties of water makes it a complex channel to use for wireless communications. Radiomagnetic waves have very limited range in water, therefore acoustic waves are used. In this report the basics of wireless communication systems are described including source coding, channel coding, modulation techniques as well as different techniques for spread spectrum.

The implementation of a material requirements planning system is a complex and demanding task. There has been much research into what factors are important in such implementations, but seemingly very little about the links between critical success factors and management control systems. This thesis attempts, through a case study, to answer the question of how management control systems affect the implementation of an MRP system in ASSA AB, a Swedish manufacturing firm. Data is primarily collected through interviews. Theory regarding implementation success definitions, critical success factors as well as management control systems is presented.

In order to reduce the price for, and improve the performance of automatic control systems for magnetization of synchronus generators, the possibilities of using a PC based software PLC system, Programmable Logic Controller, has been investigated. The result is a system based on the CoDeSys software PLC with runtime environment from 3S-Software, communicating with external units via Modbus fieldbus. System price is reduced from ?5000 to ?2000 and system processing speed is reduced from 10 ms for a Siemens S7 PLC to 4 ms with the CoDeSys PLC system though unsolved problems with runtime seizure caused by improper settings in the PC BIOS..

Complex Vertebral Malformation (CVM) is an autosomal recessive inherited defect in the Holstein breed. The defect has lead to structurally malformed calves and losses of pregnancies. To determine the effect of CVM on fertility in the Swedish Holstein Breed 375 Holstein bulls used in breeding by Svensk Avel and Skånesemin were assigned to this study. 228 bulls matched the criteria of birth year, 1995-1999, > 75 inseminations and a known CVM-status. Of the total 228 bulls 53 of them were CVM-carriers and 175 were non-carriers. The SAS-programme was used to determine the effects of CVM-status, the bull?s father and birth year on Non-return rates (NRR) for 28, 56 and 168 days.

This report presents a master thesis project performed at Elekta AB during the fall of 2013 and early 2014. Elekta is a medical technology company and their main product in the Stockholm office is a gamma knife used for radiosurgery. The gamma knife contains a cluster of a dozen motor servos and motors used for adjusting the patient and the radiation sources over a CAN bus. A self-developed hardware-in-loop simulator running on a PC with LabVIEW is currently being used for integration level testing of the control system of the gamma knife. The simulator has some problems with it not running in real-time and having other performance issues.

In this thesis a transport system is sought after thatif realised in the city of Uppsala could provide bothwell-being to all its inhabitants and sustainability,here jointly refered to as liveability. It is found thatthe car dominated transport system that is inoperation today provides two fundamental values,namely accessibility in both time and space, whichsets it apart from other transport solutions. Thesetwo values are of immense importance for theliveability in our modern world. On the other handthe car dominated system decreases the liveabilityof Uppsala in several different ways. Some of theseproblems, it is argued, could be solved within thecar system, through the adoption of moreenvironmentally friendly cars etc., but otherproblems are inherent in the car system and willremain no matter what changes are made.

Because of increasing demand of power on Malmbanan the capacity of the existing wires which supply the trains must be increased. This increases the stress on the existing poles and for this reason the system for supplying the loads along the railway is to be removed from the poles and be replaced by some other system. This thesis is a study on a two-level low voltage (1 kV and 0.4 kV) electrical system with the aim to investigate if it can be an alternative to the system used today taking into account the voltages, fault currents and costs.In this thesis the following tasks have been performed:? Gathering of data? Description of basic theory? Loadow and fault current calculations of the system with MATLAB? Life Cycle Cost estimate of the system? Analysis and conclusions from the resultsThe results show that the new system can be an alternative to replace today's system. The simulations and calculations show that the voltage drop is at an acceptable level and that the fault currents are large enough to supply a safe disconnection if a fault occurs at the far end of the system..