Performance of an intersection affects the total travel time in a traffic network. An intersection with good performance can easily be described by its contribution to lower travel time than in a comparable intersection. The travel time is of importance in the cost calculations when a specific intersection is to be chosen and designed. It is important to be able to make correct and precise performance calculations so that the cost calculations will not be incorrect. For that purpose the software Capcal, which is a traffic model for intersection analysis on performance, is used in Sweden.

A company library can only exist if it contributes to a positive result for the company. As endusers are beginning to perform searches on the Internet and have access to databases and electronic documents via their desktops it becomes important for company librarians to thoroughly think through what services should be offered to the users so that the library still contributes to the company s profit. The aim of this dissertation was to try to define the services that the company library offers its users having in mind the changes that have taken place concerning the availability of information. I also wanted to explore whether the librarians had the necessary competence to perform the services offered. Six information specialists were interviewed to give their view on the services their libraries offered.

Value stream mapping is a tool that is frequently used by many different companies. It is a great tool used to achieve the work that follows the theories of lean production. The tool is used, however, only frequent on the factory floor and the method is also designed based on this type of use.An interest of applying the method on administrative parts of the company has occurred lately. Administrative parts of the company refers to the part that does all the planning such as purchasing, receiving orders, customer contact, contact with factory floor and other work that is made around the actual manufacturing. But the knowledge about applying value stream mapping on the planning part of the company is lacking because the method is relatively new.In this work, a comparison is made between the introduction of value stream analysis on production and planning.

Mattias MogardGustav von HeijneSammanfattningFör framgångsrika företag är det essentiellt att ha kontroll över sina resurser. Studien tar upp ett ämne som handlar om att skapa en överblick och en medvetenhet om resurseffektivitet inom ett företags produktion.Performance measurement är ett tillvägagångssätt för att kvantifiera aktiviteterna inom en produktion. Data struktureras genom nyckeltal, Key performance indicators (KPI:er), till övergriplig och användbar information. ISO 22400 är en uppsättning standardiserade nyckeltal med ändamålet att appliceras på automatiserad produktion. Studiens syfte är hitta vilka av nyckeltalen från ISO 22400 som är lämpliga att använda vid mätningen av en helt automatiserad produktionskedja som tillverkar motorblock.

Syftet med denna uppsats är att kartlägga hur Performance Management-system praktiseras inom svenska organisationer. Med utgångspunkt ur de teorier och modeller som återfinns i litteraturen ska sedan resultatet analyseras. Samtliga av de undersökta industrikoncernerna har tagit till sig PM-synsättet och praktiserar det i någon mån. Skälen till detta benämns vara att verktygen i större grad än annars kan få hela företaget att uppnå gemensam fokus på företagens målsättningar. Hur detta senare visar sig i hur företaget faktiskt jobbar finns det, en del att vara ifrågasättande emot.

Facebook´s importance has grown significantly regarding crisis communication. A deficiency concerning what types of companies has been investigated earlier and how their crisis communication should be carried out on Facebook, has been identified. The aim of this study is to examine the crisis communication of a smaller company on Facebook and explore how this communication has been received by the company?s recipients. We apply an explorative approach on to a case study in order to answer the aim.

The last few decades the development in the field of electronics has been huge. The components performance gets better at the same time as the manufacturing cost decreases. Many of the design moments that have to be done, are done automatically today, but it can get better. Especially for analog circuit design.At Electronic System in Linköpings universitet, research is in progress to develop a tool that can design analog circuits in reasonable time. It means that it has to size the components (transistors, resistances, capacitances etc), so that the circuit can fulfill the performance requirements.

The study has shown that retailers in the mid-price segment differentiate their brand through developing a strong company identity around the brand. The personality involves store atmosphere, merchandise and advertising. Larger companies have chosen to lay the responsibility on management level, which facilitates on store level. By controlling the strategies on a central level the company can make sure that the stores are steered in the direction that the company wants them to be steered in, and also that they follow the positioning-concept. The company can also devote its efforts to working with its core value, which is service.

A Swedish electronics company wants to make the cooling of one of their electronic components more efficient. They propose that a retrofit liquid cooler is the way to achieve this goal. The current air cooling has high energy cost due to the high amount of power needed to power fans and heat exchangers. Using high volumes of air for cooling also leads to noise pollution. The conversion from air to liquid cooling would possibly make the operation of the electronics more cost efficient and less noisy.The purpose of this project is to theoretically evaluate different concepts of drawing the heat generated by the electronic component in to a fluid, using numerical calculations in Matlab and FEM simulations in ANSYS.

I have researched different methods for practicing with the purpose of learning some useful ways to handle my performance anxiety issues, to better understand the phenomenon, and to be able to perform better under pressure. I chose or created nine methods and used each during a decided period of time, each period ending with a performance. Afterwards I analyzed the methods with the help of audio recordings and written concert evaluations to see if it was possible to alter my practicing techniques to be more directly focused on preparing for the concert situation..

This report deals with an IT solution for the fictive company, Nexus Consulting. It is a small company with four employees, dealing with economic policy. The company wishes to set up a complete network environment with antivirus, firewall, computers and servers. They want us to analyze and compare different outsourcing companies offering cloud services and then recommend which company would suit them best.In addition, the company wants to have a webpage containing essential information about them and the services that they offer their customers.The report describes, analyzes and compares three outsourcing companies offering complete cloud services where a practical solution proposal has been developed by the group.The network component is based on the Windows platform and the web part is coded in HTML and PHP.The report also discusses what cloud computing is and why so many companies choose to move to it..

Laws, regulations and generally accepted accounting principles hold options on how companies should recognize revenue. Generally accepted accounting principles are determined by standard-setting bodies as the Accounting Standards Board and the Financial Supervisory Authority, which is influenced by international standard-setting bodies as the IASB. Service revenue is generally recognized when performance is completed, but there are variations in when a performance is considered complete. The different accounting options available create difficulties in comparing companies over time and between companies, which in turn creates difficulties to achieve a true and fair view. By clarifying what methods and principles in accounting for service income the unlisted companies in Sweden are using and why these differences exist, we have been able to study how the comparability and the true and fair view is affected by these differences.

The lifecycle of fashion products get shorter and shorter. Companies in the fashion business needto make sure that they can offer their customers the right products, in the right quantity at theexact right time. The competition on the fashion market today is tough and if companies aregoing to be successful they need to have access to the most reliable suppliers, and also offer theircustomers products with high quality to attractive prices. It is therefore of highest importance toevaluate and choose the right sourcing strategy. Product category and type of organisation aresome of the factors that will determine which strategy that is most appropriate.

At a manufacturing company, due to the competition the price is reducedtowards the manufacturing cost. Therefore it is important to maintain control ofones costs and keep calculations up-to-date.This thesis deals with cost accounting at a aluminium-processing company. The report focuses on calculating machine cost per hour since the manufacturing costs are the major part of the total product cost.Managers on the company believe that the costs they use in calculations todayneither is up-to-date nor advantageous in a market aspect and due to that their calculations need to be revised. The machines cost per hour is a major part in the manufacturing calculation. The company wants to provide a competitive price that also covers their costs.

This is a thesis for a Bachelor Degree Project, performed in the subject MechanicalEngineering. The students Roger Malmberg and Simon Hagberg have carried out adesign project on behalf of the recently established company J&D Assisting systems,located in Halmstad.The project consisted in developing J&D's first prototype of a power assisting solutionfor wheelchairs. A power assisted wheelchair combines human power, which is deliveredby the arms through the pushrims, with electrical motors, which are powered by a battery.The power assisted wheelchair is aimed at customers, who have used a regularwheelchair for a long time, but who have become weaker or just need additional powerwhen driving uphill. This kind of wheelchair will provide additional power for users,which will spare their wrists, elbow and shoulders. The product is torque sensor free andinstead it relies on the velocity.