In this report focus is put on the combustion process at a cement plant. Combustion is the heart of the cement making process and absolutely crucial to have under full control and well optimized. The fuel is put into the process through a burner pipe and this burner pipe is modified to reach a more efficient combustion. The primary target is to enable burning of heterogeneous alternative fuels and increase the production level. Other positive effects from this type of optimization is lowered specific fuel consumption and lowered CO2 emissions. A redundant burner is chosen for the project and overall the project steps are the following: 1. Installing a Jet air nozzle ring in a way so it can move both axially and radially due to temperature changes. 2.

Spårledning används inom järnvägen för att lokalisera var tåg befinner sig. Detta examensarbete behandlar en modell av tonfrekvensspårledningar från Alstom. Teoridelen behandlar de båda modellerna DTC ? 921 och DTC- 24 medan uträkningarna enbart behandlar den tidigare. Tonfrekvensspårledningar separeras med elektroniska skarvar genom förbindningar i spåret.

In Sweden there is a large interest in renewable energy but the market for solar power is still small compared to other countries such as Germany. Here many farmers produce their own electricity. The Federation of Swedish farmers have acknowledged the potential for Swedish farmer to produce electricity and there is an interest among the farmers. The agricultural branches in Sweden most suitable for solar power are pig production and poultry due to the even electricity need throughout a year. Swedish pig farmers are going through a period of unsteady profitability which makes it interesting to see whether producing their own electricity can affect the economic situation.

The county of Dalarna is at present carrying through a process of digitalization where traditional x-ray film is being replaced with digital detectors. Earlier used methods for dose optimization turned out not being sufficient. This report presents a method to harmonize dose levels between x- ray sites equipped with Fujifilm imaging plate systems. An exposure index, S, related to the dose level of the examination is computed to every x-ray image. S turned out to be inversely proportional to the detector dose used at the examination.

Today electronics becomes more and more complex and to keep low costs and power consumption, both digital and analog parts are implemented on the same chip. The degree of automization for the digital parts have increased fast and is high, but for the analog parts this has not come through. This have created a big gap between the degrees of automization for the two parts and makes the analog parts the bottleneck in electronics develop. Research is ongoing at Electronics systems group at Linköping University target the increase of design automization for analog circuits. An optimizationbased approach for device sizing is developed and for this a good optimization method is needed which can find good solutions and meet the specification parameters.

A degree project has been carried out at Motion Control, Västerås. The degreeproject ?Grafisk Skärm för Inbyggda System? have developed a first prototype of anembedded system with a display, a graphical user interface with touchscreen andpossibilities to communicate with external units.The work initiated with surveys of critical components. A technical specification forthe desired end product was developed. With the technical specification as support,design specifications for hardware and firmware were developed.After the specifications were done, a circuit diagram was developed and a circuitboard was made.

The county hospital of Dalarna has for the last couple of years carried through a process of digitalization. The result is that within the county it exists image plate systems from two different manufacturers. In an attempt to create a tool for dose optimization and dose surveillance the county of Dalarna would like to investigate if the exposure index from Agfa and Fuji is suitable as a dose indicator. An investigation of the exposure index, S, from Fuji has already been done. This thesis has been continuing the investigation by evaluating the stability of the exposure index, lgM, from Agfa.

In this Master thesis, microwave connections between circuit boards are constructed. The primary frequency band is the X-band (8-12 GHz). The purpose of the connections is to enable a more simple and cheaper way of mounting the circuit boards inside a container. The connections have been designed and evaluated, using different computer programs. A few prototypes have been built and measured.

Mechanical relays are more and more being replaced with semiconductortechnology. In this thesis it is investigated if and how the larger loads couldbe controlled by transistors. The main part of this work aims to create andverify a solution that can control the starter motor, as well as protect it incase of any failure. The different malfunctions that the solution protectsagainst is high current, too high peak current, low current, maximum cranktime and minimum cool off time. The timers also protect indirectly againstoverheating of the starter engine.The transistors used are BTS555, from Infineon.

Control of a diesel engine equipped with Variable Geometry Turbine (VGT) and Exhaust Gas Recirculation (EGR) requires a multivariable control method. One problem is that the engine system is non-linear. Furthermore there are strong cross-connections between inputs and outputs and the inputs have alsoboundaries. To be able to manage these control problems, MPC has been used that is a multivariable method. The MPC-controller consists of an optimization problem and therefore MPC can find the optimum control signals in an easy way.

Abstract. Title: Supply Chain Optimization ? for Sourced Production. Authors: Patricia Möller and Andreas Paulsson. Tutors: Jan Eskil Hollen ? Business Developer, Lilleborg as, Orkla, Everth Larsson ? Department of Industrial Management and Logistics, Division of Engineering Logistics, Lund University, Carl-Henric Nilsson ? Department of Economics and Business Administration, School of economics and management, Lund University.

The thesis aims to examine how companies optimize the human capital from a value creation perspective. The value creation will be related to transfer of knowledge, recruitment, staff turnover and development. The thesis has a deductive approach and six qualitative interviews have been conducted. The results from the interviews will be strengthened with a quantitative data analysis of two measurements; value added per employee and human capital efficiency. The theoretical framework includes definitions of human capital.

The wastewater treatment plant at GE Healthcare's facility in Uppsala deployed a three step vacuum evaporator in 2007. The purpose of this was to pre-treat wastewater containing amines. The purpose of this thesis was to optimize thisprocess by reducing the amount of concentrate without releasing more nitrogen tothe environment and to examine if density could be used as a measurement of whenthe process should be ended.To create a foundation for optimization six test cycles were conducted with samples taken from all three steps. Both concentrate and condensate were tested as well as the incoming solution. Furthermore, the thesis has been expanded with a benchmarking part examining two different evaporators.

The aim of this study was to develop a load prognosis model for Uppsala district heating system to be used as a tool for heat production optimization. The methodwas to build three models for the different customer types; housing, industry andoffices and then scale them for the total system using data from Uppsala districtheating system. The heat load consists of two parts, one that is temperaturedependent and one that is dependent of the social behavior of the customers. Thetemperature part was modelled with an ARX model using an outdoor temperatureprognosis as input signal. The social behavior part was modelled using the mean ofthe social behavior from some days before and additionally by distinguishing betweenweekdays and weekends.

Målet med detta examensarbete, utfört på uppdrag av Vectura Consulting AB, har varit att undersöka möjligheten att ansluta en vindkraftpark till järnvägens kontaktledningsnät. Möjligheten att koppla om vindkraftparken till järnvägens hjälpkraftnät, som bland annat förser växelvärmare och signalsystem med effekt, har också undersökts. Eftersom kontaktledningsnätet och hjälpkraftnätet arbetar med olika frekvenser och spänningar, 16? Hz och 15 kV respektive 50 Hz och 22 kV, måste därför en komplett krets för frekvensomvandling, spänningsomvandling och omkoppling tas fram. Projektet har begränsats till en del av Botniabanan, sträckan Örnsköldsvik-Nordmaling.I denna rapport har trafikfrekvensen på den valda sträckan på Botniabanan undersökts för att bestämma en genererad effekt till inkopplingspunkten, samt för att undersöka när det kan vara lämpligt att koppla om till hjälpkraftnätet.