In April 2007 we contacted Lennart Augustsson at Designpartners AB in Västerås. He came up with the idea to investigate and evaluate their construction of a interaction beam, CSB-beam. CSB is short for Connector Interaction beam. The beam is based on a horizontal C-profile of high-tensile steel and in the bottom of the profile are vertical flat bar welded so called block connectors. These block anchorsare also made of hightensilesteel.

The report examines the factors which may be a contributing cause to the problems that are present when ferritic stainless steel are eddy current tested in a warm condition. The work is carried out at Fagersta Stainless AB in Fagersta which manufactures stainless steel wire. In the rolling mill there is an eddy current equipment for detection of surface defects on the wire. The ferritic stainless steels cause a noise when testing and this noise complicates the detection of defects.Because of this, a study was made of how the noise related to factors such as steel grade, temperature, size and velocity. By observing the signal and with the possibilities to change the equipment settings the capability to let a signal filter reduce the noise level were evaluated.

ABB and Prevas have initiated a collaboration to sell a system to optimize steel industry furnaces, called FOCS. The purpose of this thesis is to investigate possibilities for integrating Prevas FOCS and ABB 800xA.The result of the investigation is used for an implementation of a prototype of the integrated system. The study shows a general method that can be used when implementing two software systems. The prototype of the integrated systems is made with usability principles in mind. This is a very important aspect in order to create a good working environment for the operators of a steel plant.

Atlas Copco Secoroc tillhör en av de tre ledande tillverkarna av bergborr- verktyg. Sandvik Steel har under en längre tid varit Atlas Copco Secorocs enda leverantör av hålvalsat borrstål. Samarbetet mellan företagen har lett till specialiserade produkter och en relation som är svår och tidsödande att bygga upp med en ny leverantör. Relationen har dock blivit påfrestad då leveransprecisionen från Sandvik Steel inte är tillräckligt hög. Den låga leveransprecisionen medför att Atlas Copco Secoroc får svårt att leverera sina produkter i tid.

This M.Sc. thesis is a material application evaluation commissioned by the advanced body engineering department at SAAB Automobile AB. The purpose of the thesis is to evaluate implementation of the innovative sandwich design material Hybrix into an automobile body. Today the most commonly material used in the body is galvanized steel sheets and by shifting material to Hybrix several problematic issues have to be dealt with. Hybrix is an innovative sandwich sheet that inherits thin stainless steel face sheets and a stainless steel fibrous core.

The company Olofsfors AB manufactures drive belts for forest machinery, known as ECO-Tracks, and abrasion-resistant steel and cutting edges for graders, excavators and tractors, known as Bruxite and SharqEdges. Manufacturing these products requires the steel to be heated and molded, then submerged in water and hardened. The water used in the hardening of steel is pumped to the process from pits below the floor and then pumped back to the pit after it?s been used. Since the temperature of this water rises after being used to harden the steel the temperature of the pumping pit needs to be adjusted to maintain its setpoint of 21°C.

The company Olofsfors AB manufactures drive belts for forest machinery, known as ECO-Tracks, and abrasion-resistant steel and cutting edges for graders, excavators and tractors, known as Bruxite and SharqEdges. Manufacturing these products requires the steel to be heated and molded, then submerged in water and hardened. The water used in the hardening of steel is pumped to the process from pits below the floor and then pumped back to the pit after it?s been used. Since the temperature of this water rises after being used to harden the steel the temperature of the pumping pit needs to be adjusted to maintain its setpoint of 21°C.

Österbyverken is an industrial estate in Östhammars municipality in Uppland, Sweden. Many different activities have taken place on the estate the last 600 years. During the last 15 years both health and environmental studies have been made by different companies. At the most recent study a great increase of metals in Nerån, a river that runs partly through and partly next to the estate, was identified with mass balances. The purpose of this thesis is to accomplish a deepened study about the reasons for the increase of metals in Nerån.

This thesis has been performed at Uddeholms AB with the purpose to investigate theparameters affecting the formation of inclusions during the manufacturing of a low carbonmanganese-steel.A follow-up, steel and slag sampling and evaluations in microscope have been done for a totalof five heats.The results for each heat have been evaluated in relation to the theory from the literaturesurvey and suggestions for changes in the process to reduce the amount of inclusions whichhave a negative effect on the steel quality have been given.The project extends over a large process where many parameters affect the formation ofinclusions. However, a tendency that a higher addition of alloys seems to increase the totalamount of inclusions before and after the vacuum degassing is seen.The majority of the studied inclusions seem to approach the composition of the top slag aftervacuum degassing. Ladle glaze may cause the inclusions which had a different compositioncompared to that of the slag.A high or low ladleage together with a high argon flow during vacuum degassing seems todissolve particles from the refractory which later on get trapped inside the inclusions.The floatation for two heats has been studied where a short floatation seems to give a higheramount of inclusions in casted material.In machined material so called stringers were found. The main composition of those stringerswas pure alumina. Inclusions with a composition of pure alumina were not found in the liquidsteel, thus the pure alumina inclusions must be formed during the casting.

The company Olofsfors AB manufactures drive belts for forest machinery, known as ECO-Tracks, and abrasion-resistant steel and cutting edges for graders, excavators and tractors, known as Bruxite and SharqEdges. Manufacturing these products requires the steel to be heated and molded, then submerged in water and hardened. The water used in the hardening of steel is pumped to the process from pits below the floor and then pumped back to the pit after it?s been used. Since the temperature of this water rises after being used to harden the steel the temperature of the pumping pit needs to be adjusted to maintain its setpoint of 21°C.

The last decade has created an increasing pressure on companies to decrease their impact on the environment and to increase their effectiveness of recycling the company?s resources, especially for the steel industry. Companies have also started to realize the economic aspects of an effective internal reverse logistics. In the past the value of an effective internal reverse logistic was something that companies tend to underestimate and there are few academic studies done in this area. The purpose of this essay has been to identify key factors to create an effective in plant storage, transport, sorting and handling of returned steel. From these factors a generalized model for creating an effective return steel flow will be developed.

Blast furnace is the heart of every steel plant. Steel production is based on the blast furnace process, as it is where the iron is extracted from the iron ore and turned into liquid iron, which will subsequently be used to make liquid steel. Therefore, without hot iron, steel can not be produced. Blast furnaces in this process are supplied among others with pulverized coal. Raw coal should be prepared for the blast furnaces in the form of fine coal powder.

Suggestion for a new operahouse in stockholm, förslag på nytt operahus i stockholm. Stockholmsoperan..

The aim of this thesis is to investigate the correlation between the price of electric power and investments within the Swedish basic industry. Using regression analysis, the authors test for correlation between the electricity prices and the basic industry, defined as the pulp and paper industry, the mining industry, the steel and metal industry and the basic chemical industry. Moreover, five variables found in the literature on investment decisions are being used as a means of comparison. The results suggest that the electricity price affects the investment decisions within the basic chemical industry as well as the steel and metal industry. On a more abstract level, this thesis contributes to the understanding of one of the properties of the Swedish GDP..

This report investigates the possibility of developing a new and improved hip prosthesis. The result were five different materials that could be used for the prosthesis. These five solutions were Silicone Nitrate on Cobolt Chrome, phase stabilized Zirconium Oxide on Cobolt Chrome, Silicone Nitrate on Silicone Nitrate, DLC coated phase stabilized Zirconium Oxide and Chromium nitride coated Cobolt Chrome on Cobolt Chrome. In addition to this it was also investigated how to best market the prosthesis and how to transport them from production sites to hospitals..