We have left the industrial society, and instead, we live in a post-industrial knowledge and information society. It is often said that industrial production has disappeared or that it has changed greatly. This means that fewer are employed in the manufacturing sector while the service sector is increasing, resulting in that the boundaries between production and administration decreases. The production goes from mass production to more flexible and specialized solutions. This puts greater demands on the logistics chain that continually need to work to meet customer requirements.

On today?s competitive market, it is difficult to achieve profitability trough high prices on manufactured products. Profitability must be obtained through low manufacturing costs, high quality and short lead times. One of the companies on the market is Sandvik Coromant, manufacturer of tools and chips for metal cutting. This master thesis investigates the methods of manufacturing for boring bars at the manufacturing unit GVH4 at Sandvik Coromant in Gimo, Sweden.

The objective of this thesis is to map the resources and methods used at the department OPPC, at AstraZeneca, and derived from that give suggestions on possible solutions that will increase their productivity.Mapping of the product flow, as well as gathering of process data, has mainly been done using observations, but consultation with the process technicians has also played a great role. Further have theoretical methods been used, based on literature studies, within the areas of Lean production and statistics.The work has incrementally gone forward since the steps taken has been restricted by the irregularity of production which led to the need of creating a fictive production flow. This has affected the lead-time calculations in the way that they are meant to give an indication, rather than an absolute truth, on how different methods described shall be used.The current state analysis showed multiple areas of improvement when defining capacity as value adding time in relation to total throughput time. Using the "standard scenario" as a basis showed that the actual production flow only constituted 50% of the total project time. Further it showed that the workflow contained more non-value adding activities than value adding activities, which is a result of how the work is distributed within the department as well as in the different projects.

Since 2004, wind power has had the largest installation of new capacity compared to other energy sources in Sweden. Accommodating new wind power may require strengthening or rebuilding of the existing grid in areas where the grid is already loaded to maximum capacity. This master thesis examine the possibility of a new 400/130 kV substation in Yttermalung, Sweden, with a connection to the two neighboring regional grids in Dalarna and Värmland owned by Fortum. This substation would provide a new connection point to the Swedish transmission system as well as an interconnection of the two, currently separated, regional grids. Different expansion scenarios where a substation with and without series compensation or a phase shifting transformer (PST) to control active power flow were studied.

The thesis that follows is performed in collaboration with Nitator in Oskarström.The factory in Oskarström focuses on laser cutting, robotic welding and surfacetreatment of steel for the automotive industry.The project aims to streamline the flow of materials in production by automatingthe movements of the forklifts, running to and from the interlayer, and betweenworkstations.The project started with a systematic literature search. The literature searchshowed the research position around the AGV-system. Also a review of studentliterature was made, so that a suitable method for practical implementation couldbe developed and applied. Selected method uses both quantitative and qualitativeapproaches, which is analyzed by using triangulation.The work has resulted in a modified layout of the current facility in Oskarströmthat can be used for the implementation of the AGV-system. It has also resulted inthe tender documents and profitability calculation from several of AGV-suppliers..

In the year of 2009 the conditions for managing primary healthcare in the region of Västra Götalandchanged. The decision was taken by the regional assembly and resulted in that the citizens since thenhave had the opportunity to choose which health care provider they preferto stay with. Along with thisdecision a new market for private health careproviders was established, which resulted inincreasedcompetition between the providers.In order to manage the competition, the health care providers arenow forced to be more efficient in their operations andalso to beeven more focused on their patients.Backa Läkarhusgruppen is an example of a private healthcare provider in the region of Västra Götaland.In the same way it is also an example of anorganizationin need of analysing their operations to seehowit can be further optimized to meet patient needs and expectations.The aim of this study is to analyse Backa Läkarhusgruppen?s organization and its operationsin the hopeoffinding suggestions whichwill improve the patient flow.To allocate and solve the problems thatBacka Läkarhus suffer from,an approach inspired by Lean Healthcare is used throughout the report.Some of themost significant problems that were identified within the organization are:?The synchronization of demand and capacity is inadequate.?Absence of standardized routines.?Absence of present leadership.To be able to improve the patient flow Backa Läkarhus needs to handle these identified problem areas.By synchronizing the staffing level in relation to the trends in demand a reduction in the patient?swaiting times and throughput time will be possible. Creating clear responsibilities and routines for thestaff will contribute to a higher degree of patient focus and thus lead to a more efficient patient flow.

In the last decades, lean production has proven to be one of the most important organizational paradigms in manufacturing. The lean concept has also spread into the service industry where it is applied within a range of different areas. The wide applicability of lean principles has spurred the authors of this study to apply the principles in the context of the operations of a Swedish remand prison. The thesis examines the process a client of the remand prison Häktet Kronoberg goes through from the time of arrest until he/she is released or convicted and transferred to jail. Based on lean tools and principles, the thesis maps and analyses this process.

A district heating plant has the advantage that it can take advantage of the waste heat from industries and use of cheap fuels to produce heat. But for the long term is competitive requires that energy is also saved in district heating plants. One way to save energy in a district heating system is to increasing cooling to the return temperature. This leads to less power needed to drive the distribution pumps,  and that more energy could be extracted from the same amount of fuel by an improved flue gas condensation.In Karlskoga the return temperature into the district heating plant is high. They would therefore reduce the return temperature in order to extract more energy from the flue gases.

As stocks have become a more common way for people to save their money, the range of financial information has had a substantial increase. To understand the assumptions that stock valuation and analysis are built upon, it is important for the reader to have an understanding for the models that are used by banks and institutions when recommendations are published.The Cash flow model, which is the most commonly used stock valuation tool, is based on CAPM. This model describes the relationship between an assets return and its risk in relation to an index. The risk parameter is called the beta value and has grown to be the dominating risk factor within financial economics literature.The use of beta values has been widely discussed in the world of academics and some researchers claim that the degree of explanation brought about by the beta is so low that it should be discarded, others are faithful to the beta and believe that it still serves a purpose. As a result of this criticism other ways to calculate the beta have surfaced, models that take other factors of risk into consideration.

This master thesis was a continuation of a previous study in the diesel exhaust characterization, which is part of the academical work embedded in the EMIR-1 project. The main objective of this thesis work was to finish the installation and make the proper modifications of the particulate mass measuring system located in one of the engine test cells at KTH, in order to be able to measure the mass of the particles from the exhaust of diesel engines.This experiment requires a diluted flow sample from the exhaust that should be sent to the device that makes possible the measurement of particle mass, called TEOM. In the first stage of this project, the objective was to study and make the proper modifications in the existing KTH diluter because there were several problems to obtain a constant dilution ratio from it during tests.This modifications were made and it resulted in a great improvement in the maximum inlet and outlet flow that this diluter can handle. Therefore another modification is proposed for controlling the inlet exhaust flow so it will be possible to regulate the dilution ratio and make it constant along a wide range of engine loads and speeds.The second and most important stage was to make particulate mass measurements possible by analyzing the frequency signal from the TEOM device. The idea was to obtain the frequency of oscillation from the tapered element in the TEOM, and therefore with the proper correlations, be able to predict the particulate mass concentration in the exhaust flow from the engine.An electrical problem in the TEOM circuit was detected and corrected, so the signal that carries the frequency from the TEOM can be analyzed properly.

Ericsson?s factory in Kumla, Modules Kumla, became a hub for radio modules and micro base stations, which enables mobile communication through radio base stations, in 2004. Because of this the factory focuses more on the logistics operations. This has led to a need to be able to plan the capacity for the materials handling system. This master thesis has therefore been performed at Modules Kumla to develop a capacity calculation model for the material handling flow during the autumn of 2005.The work has contained a mapping of the material handling flow regarding to which activities was performed and how much time they consumed.

Together with NCC and Sweco we measured the air-flow on a semi-detached house in Jönköping. When a pressure measurement is made, the house gets exposed to over- and under pressure. This is done in order to examine the houses climate shell. The climate shell of the semi-detached house we tested exceeded the required air thickness in BBR-2002, hence, measures have to be taken.This report also displays the importance of building air thick houses and what consequences a non air-thick house can have for the ones residing the house. A discussion of different measures is on for the addressed problems with the flow-measurement and the alternative construction-solutions.Furthermore we have described in this report of how to account for the performance of the air pressure, what kind of equipment we used and how we came up with the results.

 This study was conducted in autumn 2008 on the Company AB, which is currently in a growth phase. The company manufactures hydraulic systems for the heavy vehicle industry and has annual sales of approximately 250 MSEK with 165 employees.The rapid growth and unchanged planning is the starting point for this report. It all began in 2005 when the company received an unusually large order. During this period, the first priority was to satisfy customers and all other focus was disregarded. This has primarily resulted in a messy production and long throughput times.

The online gambling market has during recent years experienced high growthmostly due to the popularity of online poker. Today other games such as casinoare growing in popularity and more customers are turning to the onlinegambling market instead of the regular gambling market. As with all growthmarkets more and more companies establishes on the online gambling marketeven though high external risk factors such as regulations and nationalbans. Companies such as Betsson connected to the online gambling marketsuch are experiencing high growth which has made them interesting objectsfor investing.This bachelor thesis intends to study competitive advantages, investigate possibilitiesto keep and increase market share, and use this information combinedwith a financial analysis. The purpose of the thesis is to describe andanalyze the future of Betsson AB from the perspective of an investor.

Syftet med denna uppsats är att utreda vilka faktorer som påverkar de svenska småhuspriserna, och i så fall hur och i vilken utsträckning. Med stöd av tidigare studier som enhetlig pekar ut bolåneräntan och disponibel inkomst som de faktorer vilka har tydligast inverkan på fastighetspriserna i Sverige, utökas de förklarande variablerna i denna studie med hjälp av en stock-flow modell. Tidsseriedata från 1993-2013 behandlas för enhetsrötter och kointegration för att skattas i en regressionsanalys i form en "Error Correction Model", med avsikten att utreda både ett kort- och långsiktigt samband. Resultatet bekräftar reporäntan och disponibel inkomst som två viktiga faktorer för att förklara det långsiktiga sambandet med priserna på småhus i Sverige, tillsammans med ytterligare faktorer såsom BNP, hushållens skuldsättning och arbetslösheten. På kort sikt är dels den historiska utvecklingen av huspriserna en nyckelfaktor, men faktorer som disponibel inkomst, ränta, BNP och hushållens skuldsättning är också viktiga krafter för att förklara småhuspriserna.