This thesis assignment at C-level is focused on calculation models and prediction methodswhish can be used in the stage we call ?prospecting? of possible windmill locations. Thelocation is southeast of Halmstad at the Farm ?Stjernarpsgods?. The rapport has two mainareas directed towards this task.

This work is a part of the project ?Våtmarker i odlingslandskapet ? uppföljning av miljömålen? (Wetlands in arable land ? following-up of the environmental goals). The main objective with this project is to study nitrogen and phosphorus retention in a constructed wetland by using mass balance calculations. Continuous measurements of nutrients and water flow through the inlet and the outlet of the wetland are made. However, substantial amounts of nitrogen and phosphorus were assumed to reach the wetland with a drain-pipe transporting wastewater from nearby houses (10 persons).

The streetscape is a complex environment with a lot of different parts and users. If you look at the streetscapes main parts you have floor, walls, roof and furniture. The floor in the streetscape, the street, consists of the ground and the paving. It can be made of a lot of different materials with both architectonic and practical functions. The walls usually consist of the houses. They have a big influence on the streetscape depending on architecture, heights and widths.

This final thesis is performed on commission of Hargs Bruk Ltd. Hargs Bruk manages one of Sweden?s largest privately owned forests. A main part of the managed forest is situated in Roslagen in eastern Uppland. Since 1934 felling calculations have been performed within the estate every tenth year.

As requested by the company Husqvarna AB, we have developed a prototype of an electrical start device to a chainsaw. This was done through the development of new details in Catia, which has been integrated with existing details. Electrical components have been purchased by HAB electronics. In parallel with the modeling calculations was done, which was the basis for determine dimensions and the choice of an electric motor and gears. Prototype 1 improved gradually and led to prototype number 2, which became the final result.

A possible way to reduce pollution and slow down the process of global warming is to increase the usage of renewable energy sources. One of these renewable energy sources is solar power. With the aid of solar panels and solar cells the energy from the sun can be transformed into both heating and electricity. The requirement to use the sun in this fashion is a suitable surface, for example a big roof, an angle between 40-60 degrees and that the surface should be exposed to the south. Almost every farm meets these requirements.

Lokala investeringsprogram was a subsidy program which supported environmental reforms during the years 1998 to 2002. The subsidies were given to Swedish municipalities. Most of the evaluations of the subsidised projects have now been completed and included in a database. The purpose with this thesis is to analyse whether the instrument has been effective with respect to carbon dioxide reductions and costs. These calculations have focused on subsidy and cost efficiency. The analysis has been compared with a previous report called "LIP ur ett samhällsekonomiskt perspektiv". The result shows that the reduction cost for one kg CO2 has been almost one SEK, which is twice as high as the cost reported in a previous report, half a SEK.

This thesis has been carried out on behalf of IV Produkt AB and intends to set an average ratio of thermal energy losses in apartment buildings that were built during the 1960-1990. This shall be derived by analyzing the total district energy consumption that has been divided into three parts: heat energy losses (the actual heating requirements), the heating of domestic hot water and heating energy consumption for the controlled ventilation.Three different residential areas that were built during the years 1962-1966 and one that was built in 1993 has been analyzed. All residential areas are located in Växjö urban and contains between four and six apartment buildings.The analyzed objects have a mechanical exhaust ventilation systems and district heating as the heating method. No own laboratory work or experiments have been done in this thesis, the calculations have been done on the basis of parameters from VEAB, interviews with property managers, and literature studies. By calculations, we have got a result that is reported in Chapter 6.

The objective of this thesis is to map the resources and methods used at the department OPPC, at AstraZeneca, and derived from that give suggestions on possible solutions that will increase their productivity.Mapping of the product flow, as well as gathering of process data, has mainly been done using observations, but consultation with the process technicians has also played a great role. Further have theoretical methods been used, based on literature studies, within the areas of Lean production and statistics.The work has incrementally gone forward since the steps taken has been restricted by the irregularity of production which led to the need of creating a fictive production flow. This has affected the lead-time calculations in the way that they are meant to give an indication, rather than an absolute truth, on how different methods described shall be used.The current state analysis showed multiple areas of improvement when defining capacity as value adding time in relation to total throughput time. Using the "standard scenario" as a basis showed that the actual production flow only constituted 50% of the total project time. Further it showed that the workflow contained more non-value adding activities than value adding activities, which is a result of how the work is distributed within the department as well as in the different projects.

In each classroom there is a teacher with good intentions wanting what´s best for their pupils. But grades and tests in mathematics from 2009 in Sweden shows there is a crack between the subject being taught and the learning child. The purpose with this research is to find an understanding from a teaching and learning perspective of which teaching method is more suitable for teaching and learning mathematics by doing a comparison between two methods. The main question is:What are the advantages and disadvantages of the traditional and the laboratory method of teaching, supported by the two keywords teaching method and learning?This C-paper is based on a qualitative research aiming to gather an in-depth understanding of human behavior.

Outages in the electric grid can be costly for society. Because of this, reliability is one of the parameters used to regulate network companies. Reliability in electrical grids can be measured with SAIDI, system average interruption duration index, which for Fortum Distribution has increased in Stockholm?s distribution network (11 kV) in the early 2000?s.By using outage data for Stockholm from 2011-2013, sets of parameters to be used for reliability calculations in the network information program Tekla NIS were derived. Two different options for investment were then analysed: changing old cables with high fault frequencies, and installing automatic switching in distribution substations.

The purpose of this thesis is to investigate the degree of influence of holes in the web of steel beams with long spanson weakening of their bearing capacity. Making holes in the web of the beam generally reduces the bearing capacity of the beam. However, it might be necessary seen from both an architectural perspective as well as from a building services perspective by creating an opportunity for building installations.The objective of this thesis is to examine how much an I-beam can be weakened without sacrificing safety and functionality. The investigation has been done by using Finite Element Method through commercial software.The regulation for structural design of building structures in Sweden used to be specified in the document known as BKR. But this was replaced by the European norm Eurocode back in May 2011.

Examensarbetet syftar till att hitta samband mellan ytliga sprickor hos virke, i form av dimensioner och karaktärer, som dagens maskinella avsyningssystem inte klarar av. Tyngdpunkten i projektet har legat på att identifiera eventuella samband mellan verkligt djup hos sprickor och de ytliga sprickmått som kan uppmätas med automatisk avsyning av WoodEye. I huvudsak har projektets praktiska undersökningar gått ut på att bestämma sprickors ytliga dimensioner, djup, typ och position med hjälp av automatisk avsyningsutrustning (WoodEye) samt genom manuell uppmätning i ett antal itusågade sprickzoner. Det provmaterial som använts i utförda försök och som legat till grund för efterföljande sprickanalyser har varit av sådan karaktär att det kunnat jämställas med konstruktionsvirke som normalt sett hållfasthetssorteras enligt europasstandard SS-EN 14081-1.I projektet har 568 sprickor, fördelade över 8 olika spricktyper, analyserats. Av erhållna resultat har det konstaterats att störst respektive minst medelbredd uppvisades hos kådlåpor respektive kantsprickor, störst respektive minst medellängd uppvisades hos splintsidesprickor respektive kådlåpor, samt att störst medeldjup uppvisades hos fäll-, kap- och stormsprickor.

The third most common conifer in Sweden is Pinus contorta (lodgepole pine). It originates from the western part of North America and was brought here in the end of the 1920s. The lodgepole pine is today allowed for commercial plantations in central and northern Sweden, excluding high altitude locations. Since 1979 only plantations with scientific purpose are allowed in south-central and south Sweden. This document is focused on how lodgepole pine manage perform compared with Pinus sylvestris (Scots pine) in the southernmost part of Sweden, Götaland. The idea came from the fact that the Swedish government is evaluating a notification from the National Forest Agency that suggests lodgepole pine to be allowed for commercial plantation even in southern Sweden.

The energy that the earth receives from the sun hourly has potential to cover a year?s energy demand in the world. Further, this type of energy is environmentally friendly, natural and free of cost. This report covers solar energy in an urban environment and consists of a case study of installations of photovoltaic cells in a part of the city of Stockholm. It is mainly the economic aspects that are covered but there is also a discussion about the practical consequences and the sustainability as a result of integration of solar energy in an urban environment. The aim of the study is to present results from economic calculations for utilization of solar energy in chosen buildings in Kungsholmen in Stockholm.