In this work, a method was developed and evaluated for Calculating the life of welds under the influence of fatigue loads from a vibration environment. Typically, a shaker table is used for testing a component against vibration loads. The shaker table creates a vibration environment that is defined in the frequency domain by a power spectrum.Similarly, a virtual vibration table can be used to calculate the same type of load environment, which can then be used to calculate the expected lifetime. The benefit of this method is that it can be used in design, as well as in simulation of tests before physical verification tests are carried out.Today there are methods for Calculating fatigue life of non-welded base material, but since many components contain welded joints, there is a need to apply this method to those types as well. To achieve this, the thesis combines two different areas, which together provide a method for fatigue assessment of welds using a virtual shaker table.The methodology is carried out by modeling the component, and its welded joints, in a finite element program.

Single vehicle accidents are one of the most common types of accidents that occur on the Swedish road network. Depending on the design of the road, the presence of a crash barrier and embankment on the roadside, the outcome of a roadside collision can lead to serious injuries and even deaths.The aim of this project is to investigate the possibility of improving road safety by designing the optimal roadside area based on the results of a life cycle cost analysis (LCC).The questions that have been answered during the duration of this project are:1) Describe the current technical solutions for roadside area design and the various barrier types used in Sweden.2) Complete an existing mathematical model that has been developed by Hawzheen Karim, for Calculating life-cycle costs for various roadside areas.3) Calculate and compare the life cycle costs for the side area with a barrier and without a barrier.By performing an analysis of the documentation on the current guidelines and rules for shaping the roadside, was it possible to describe the current technical solutions for the formation the roadside as well as the current roadside barriers in use today. A mathematical model for Calculating the life cycle costs of different barrier types had already been developed by Hawzheen Karim. This model was supplemented so that it could calculate life-cycle costs of the roadside region with and without a barrier. After the model was completed, an analysis was performed to obtain life-cycle costs of a roadside with and without a barrier.The result showed that there is a clear relationship between the slope inclination, fill height, and the rate at which the costs rise.

This paper deals with evaluating 3D-bootstrap for the mining company New Boliden in an attempt to revise their current method of Calculating average gold riches in different areas. The purpose is to find one-sided 3D-bootstrap confidence bound of the average gold riches. There lacks well-defined theory behind using 3D-bootstrap, in this paper the variogram is used as an estimate of dependencies between the observations, and the block length is chosen to be higher than this estimate. In aid of this, a simulated data material is conducted to check the validity of 3D-bootstrap in a controlled area where the theoretical value is known. The results are inconclusive, and further studies are needed..

Before the European construction standards were introduced in January 2011, it was mainly themethod in BBK04 that was used for Calculating punching capacity in concrete structures, and in lesscommon cases the method in BHB. The method of BBK04 is easy to use and have had the samestructure since the first was published in 1979. The Concrete handbook method (BHB) where usuallyonly used when a higher punching capacity was needed and the cross-sectional height where fixed,calculations using this method entails more work, but will in return usually give a higher capacity. Italso allows the use of shear reinforcement to increase the cross-section capacity. The method ofCalculating punching shear in EC2 differs largely from the methods of BBK04 and BHB.

Companies have in the past decades changed fromtraditional manufacturing organizations into serviceorganizations. For these service organizationsinformation and competence have become animportant resource. The traditional view oninformation is that an employee use and search forinformation to reduce uncertainty for their decisionmaking. Even though information is strategicallyimportant for organizations, information is not valuedin any way. Hence, this thesis aims to valueinformation in terms of the utility it brings to theorganization.The conclusion is that four factors are important whenvaluing information in terms of utility.

Many dairy farms doesn?t keep their bull calves and cross cow calves, they sell them to breeders instead of raising them their self. It should be possible for the dairy farmers to do it them self?s. There is also a possibility to bread one calf from the cross heifers. The purpose of the investigation was to see if there is any economic possibility to breed beef cattle. I have used the same sample farm trough the hole study, because it would be easier to fallow the study.

The building industry consumes approximately 40 % of the total energy consumption in Sweden, where the using stage is dominating with 80 %. There is a lot of work in progress to reduce energy use in the building industry, and the demands from authorities regarding energy use increases. As a part of this work Building and planning department of Sweden has established a requirement that has been applied since 2006, and restricts a maximum energy use for buildings.The requirement includes that an energy simulation must be done in advance to demonstrate that it is possible to meet the demands.Reality is however more complex than an energy simulation program, that frequently underestimates the energy use of buildings. The purpose of this thesisis to study and analyse deviations between estimated and actual energy use in modern apartment buildings. The study includes four apartment buildings in Stockholm, Gothenburg and Jönköping that were built in 2007-2009.

Small hydropower plants have been an important source for electricity for many years. During the 70?s the general thought was that nuclear was the future. Around 2000 small waterpower plants were shut down. It wasn?t profitable to invest in.

Asset management in insurance companies differs from conventional asset management to the extent that respect has to be taken to both assets and the commitments the insurance company has towards its customers. A model that has proven to fit well regarding the matching of assets and liabilities is the Asset Liability Management Model (ALM model). In addition to the matching in the balance sheet, the ALM model can be used in a company's work with strategic portfolio allocation by applying it as a basis for analyzing investment strategies with expected risk and return. From this, the ALM model also becomes relevant for Calculating key figures according to the legal framework Solvens II which includes laws and regulations regarding the demands on economical strength (solvens) of insurance companies.Hence, the goal of this masters thesis has been to, on behalf of Bliwa Livförsäkring, create an ALM model to support the asset management department of Bliwa in their work with defining a credible way of analyzing the future risk and return of Bliwa's asset portfolio and insurance undertakings.The ALM model generally consist of four submodels, the scenario model, the liability model, the asset model and the company model, where the scenario model often is named as the core of the ALM model. The course of action has been to develop these submodels individually, with focus on the scenario model.

One problem in today?s indoor air quality lies within insufficient ventilation. Dynamic ventilation can be obtained by implementing a Demand-Controlled ventilation (DCV) system. DCV systems adjust the ventilation in a building by Calculating the impact made by its? occupants.

As trucks are getting more and more advanced, information about their weight has become a key factor for controlling them in a more fuel efficient and safe manner. Knowing the mass of a heavy duty vehicle in real time has been a difficult challenge for the truck manufacturers. With the processing power for electronic control units in trucks steadily increasing, more advanced algorithms for Calculating the mass has been developed, but at the moment there still is a wish for better performance.Since there is a lack of good information regarding the external forces acting on the vehicle, forces that depends on the slope of the road, foundation of the road and the wind, the methods have to be able to disregard these. Such an approach, based on an indirect least square solution, has been evaluated in this thesis. The results have been promising and based on these a recommendation about further evaluation has been made..

The purpose of this report is to document the experiments carried out, methods used and results gained during research into how the silicon content of an aluminium alloy affects the coefficient of thermal expansion (CTE).The goal of this paper is to better understand and to find a relation between silicon content and the coefficient of thermal expansion.Experiments were carried out using carefully prepared samples of Al Si alloys (0, 7, 10 and 20% Si content). Using these alloys, the CTE could be measured using a dilatometer.Comparative analysis carried out could map the effects of silicon content on the coefficient of thermal expansion and an equation was created. Using simple graphs and the rule of mixture method, the authors were able to build a simple tool for Calculating the CTE of specific aluminum silicon alloys..

The purpose of this thesis was to create a saw pattern program for the sawmill industry. I have chosen to focus on the module that describes the shrinking on the wood. There are several theories about how the wood deforms by shrinking. Several hypotheses were simulated in the program and after testing them I decided to use only one of them (hypothesis C). The program is written in Visual Basic .NET and I choused that program language because it is easy to do changes in the layout. Another great advantage in Visual .Net is that you can mix different languages in the same program.

To be a part of the future we have to make a profit, one way to improve the profit margin is by reducing the fixed costs. This paper discusses the financial results of equipment cooperatives in crop production. Through a case study of three farms in Södermanland, we have an example of how it can look today and how it could look tomorrow. The three farms are crop-producing farms with slightly different orientation. Jursta Gård, 155 hectares, and Djursnäs Säteri, 215 hectares, have grains crop and oilseed crops as the main crops, and Nibble Gård, 340 hectares, mostly have pasturelands and some grain crops.

The aim of this master thesis was to measure the terminological consistency when indexing fiction. The study included ten participants, five librarians and five patrons who indexed two novels in three steps. Besides Calculating the terminological consistency a typified index based on the term frequency was created.Subject heading list Att indexera skönlitteratur was used as a controlled vocabulary and to calculate the consistency the asymmetrical formula was used.The result showed that the study produced relatively high consistency values compared to other studies. The subject heading list increased the consistency value for all of the participants, for the patrons the increase was substantial. The librarians produced higher consistency values compared to the patrons in almost every step and they had in percentage lower amount of terms used only once..