The effects of dexmedetomidine and butorphanol sedation on skin reactivity during intradermal testing in healthy dogs were evaluated. The effects of dexmedetomidine and butorphanol were compared to medetomidine, a sedative agent having scientific proof of not interfering with skin test reactivity, in a randomised, double blind, cross over study performed on 8 adult dogs. The dogs were sedated with medetomidine (Domitor vet.®, 0,01 ml kg-1) intravenously, or dexmedetomidine and butorphanol intramuscularly (Dexdomitor vet.®, 0,01 ml kg-1; Dolorex vet., 0,01 ml kg-1) after which they received intradermal injections of positive control solutions (histamine 0,1 mg ml-1, 0,05 mg ml-1, 0,025 mg ml-1), a negative control solution (0,9 % NaCl) and allergen extract (Dermatophagoides farinae, Cladosporium and Artemisia vulgaris). After a wash out period the trial was repeated with a reversed sedation protocol.Skin reactivity (wheal size, induration and erythema) and quality of sedation (immobilization, response to stimuli and injections as well as over all working conditions) were evaluated. The combination of dexmedetomidine and butorphanol provided reliable, good sedation and analgesia without adverse effects.

During the past few years there has been an observed decrease in physical fitness within different patient groups. As a part of the rehabilitating physiotherapy treatment it is important to acknowledge the physical condition of the patient. Physical fitness testing might be difficult due to physical limitations within different patient groups. A broad range of exercise tests is therefore of importance in clinical practice. The aim of this overview was to describe exercise tests used in rehabilitation contexts, and to define areas of use and restrictions.

There are several ways of conducting software testing where some may include users and others may include personnel whose work task is to execute test on systems. Although most developers and project managers understand the point of testing the system, it is not always being done and the most common reason is that there is no time for it. However, this is a false assumption as it may instead cause some bugs in the system that would not have been there in the first place if tests had been there to prevent bugs in the code.My purpose for this thesis was to find suggestions for changes in the development process in an ongoing project used by Acino and Svenska Försäkringsfabriken in order to increase the quality of the system used. In this thesis, I have approached the purpose by pursuing a case study of the two companies through observation and interviews. By doing this I acquired the relevant information to make suggestions for change.

This thesis work has been performed at the Division of Assembly Technology at Linköping University for a period of ten weeks. The work is part of the project ProFlexA, which is a research project in collaboration between Linköping University, Lund University, and industrial partners such as Combi Wear Parts and Smålands Stålgjuteri AB.The casting process creates random incurred burrs and defects, which must be removed during a cleaning process to make sure that the cast can be sold. Automation has long been sought for the cleaning of castings due to, among other things, poor working conditions for staff, but this has proved difficult to implement with today's technology. Automation has for some time been available for more capital strong companies with large annual volumes, but for smaller companies with small-and medium-sized volumes, automation has not been an option.The goal of ProFlexA is to develop an automated cleaning cell aimed at small-and medium-sized volumes.The goal of the thesis is to do a pre study at ProFlexA?s partners on cleaning of castings, and develop concepts for automated cleaning of castings.By recording the process and cycle times, the cleaning of castings has been documented as it works today, and on this basis, information and statistics has been compiled.

This report examines the possibility of optimizing troubleshooting log files generated when constructing new Volvo trucks. Errors occur when CAD models are stored and managed by the versioning system PDMLink. By developing a new diagnostic tool, Log Search, the troubleshooting process is automated and thereby streamlines the current manual search..

This paper is part of the research programme ViSuCity, a programme with the goal of creating more sustainable urban planning through the development of better visual tools, which ultimately means better communication between various parties of public planning. The paper concerns the implementation of MCE into a 3D program for visualization. Multi criteria evaluation (MCE) is a technique that has been developed during the last 20 years. It merges GIS with AHP, forming a decision making tool for localization of, for example, new buildings.The result is an automated tool that enables advanced analysis of geographic areas.The tool has a very high potential due to the completely automated MCE and it is adapted for people without a technical background, let alone formal training in MCE. It provides great opportunities to test different scenarios, something that should be an important advantage.

This report is the result of a thesis carried out during the spring of 2010 at Sandvik Coromant in Gimo. The purpose of this thesis has been to make an inventory and mapping of information used by flow groups that are most relevant for the day-to-day work. This mapping will then form the basis for information supplied by an automated system.The project consisted of:Identifying how the information is supplied today.Inquiring into the needs of an automated system.Which needs of information that will be provided by the system.Data collection occurred in two ways, both through observations and interviews. Observations of the participants were carried out early in the thesis, where the aim was to create a picture of the problem, and gradually develop a basis for the actual interview study. At each observation, an unstructured observation was used, which means that all activity was recorded.

Modern semiconductor design methods makes it possible to design increasingly complex system-on-a-chips (SOCs). Testing such SOCs becomes highly expensive due to the rapidly increasing test data volumes with longer test times as a result. Several approaches exist to compress the test stimuli and where hardware is added for decompression. This master?s thesis presents a test data compression method based on a modified facsimile code.

This essay examines pull-out strength of threaded rods fixed into glulam timber. The technology is intended to be used in hidden joints between glulam components. The work began with a study of literature focusing on current research within the topic, mainly to create a base of knowledge before the testing was initiated. Studies of scientific articles reveals a lack of research within this area, which makes it difficult to develop standards and calculation models for these joints. The drill holes in the tests have a diameter of 7 mm.

The purpose of this thesis was to design an electrical system for use in a ballistic test at the Swedish National laboratory of forensic science (SKL). The detector unit would use four main parts: coilsystem, transmitter, reciever and indicator. The coilsystem would be based on a balanced system using three coils. One that creates a magneticfield and the other two will sense the differences when a metallobject is in the coilsystem. This report starts out by investigating possible solutions for this specific task followed by a description of the physics that the metaldetector use.

AbstractA continuous improvement of products and production is an important goal for a modern industrial company. A small engineering group located in Sweden came in touch with the authors of this report during the spring semester of 2014. The aim of this report is, as part of the group´s ambition of improvement, to analyse ways in which the quality of component casted parts can be verified. Non-destructive testing (NDT), and methods to use it for quality control, is the main focus of this report. However, fields such as material standards, component casting and quality engineering are analysed as well.

This report describes the construction of a climate-cabinet for testing of HV-cards (High Voltage) produced at VG Scienta. The main part of the report describes all the different components of the cabinet. The most important parts are a PID regulator from Eurotherm model 2408, a solid state contactor (SSC), a thermocouple, a finned resistor from DBK and different fans. The report even includes the connection between components by cable wiring, isolation, grounding, fuses and shaping of metal goods.As the cabinet also communicates with a computer, the report includes the solution of the data communication using the software iTools from Eurotherm. The communication part includes information about a converter that converts EIA422 to USB.The cabinet was produced at a company, called VG Scienta, in Uppsala during the spring 2010.

Alternative splicing is a process that partly rejects the common definition of a gene ? that one gene codes for one specific protein. By variable combination of coding regions (exons) and exclusion of non-coding regions (introns), formation of several different mRNA-transcripts, and consequently several different proteins, can derive from the same gene. Alternative splicing is an important condition for the development of complex life forms, but it is also a highly sensitive process and inaccurate splicing is the cause of approximately 15 % of mutations that cause genetic diseases. This article presents four genes, BRCA1, BRCA2, ER? and ER?, and inaccurate splicing of these genes increases the risk of developing cancer, particularly breast cancer and ovarian cancer.

Completed durability testing of gearshift gaiters at Kongsberg Automotive in Mullsjö, is sometimes leading to discussions regarding whether or not a gaiter is supposed to be a pass or a fail. That is because the current pass/fail-criterion are a bit vague. A durability test takes around 4-5 weeks to complete which is a long time if the tested material does not pass the test and a new material has to be tested instead. Stricter pass/fail-criterions and a faster testing method for the materials are therefore desired.In order to develop a durable pass/fail criteria, seven already judged gaiters were chosen. Every one of the gaiters was put through detailed analysis, after which there were a new assessment of the gaiters.

This essay is about testing the validity of an article written by Jonas Löwgren, called The use qualities of digital design. The study we have executed is about testing the featured qualities of digital design in the article on two search systems located in the library of Stockholm University and Södertörn University respectively to see how they are able to be applied on search systems. To acquire the information for the study, we handed out a written inquire among users of those systems. The result of this quantitative study shows us that many that five of Löwgrens qualities is likely to be present on the systems. Our conclusion is that five of these are appliable on search systems.