This thesis has treated a three-axis robot which task is to serve a larger test machine tomove the modules to be tested, from the storage to the test site. The robot is composed ofthree linear actuators; two standard components of ball screw type and a custom-builtactuator of trapezoidal type. The work has mainly focused on the custom-built device to seeif it could be replaced with a standard component. Part of the work has been to look into thepicking tool and to see if there are any possibilities to improve its function.The report presents two different proposals which I decided to call Robot 1 and Robot 2 andthey aim to address the problems arising in the purpose-built linear unit and the X-axislinearity problems. Robot 1 focuses on eliminating the problems that arise around therobot's X-axis, with such simple means as possible and without making excessive materialchanges.

This master thesis studies how much the cycle time, i.e. the time it takes for an industrial robot to perform a given task, can be reduced if an extra degree of freedom (DOF) is added to the robot system. The extra DOF consists of a linear track, which is supposed to be used in an optimal way. The problem has been studied using simulations in the robot simulation tool RobotStudio. To be able to run an optimization in Matlab, with the RobotStudio simulation cycle time as the object function, communication between Matlab and RobotStudio has been set up with an interface written in Visual Basic.

Picker robots are often mounted close to each other above a conveyor belt. To be able topack robots even closer, it is desirable to reduce the footprint of the robot?s base. One way toachieve this is to skew the arms of the robot which makes it possible to move them closer toeach other.This Master Thesis has been carried out at ABB Corporate Research. The purpose is toevaluate the benefits and drawbacks for the idea of making today?s Picker robot morecompact by skewing the arms.

Denna rapport behandlar utveckling av en tvåhjulig balanserande robot. En PID-regulator är implementerad i en mikrokontroller, som även AD-omvandlar en sensorsignal, samt styr motorer via H-bryggor med pulsbreddsmodulering. I rapporten förklaras framtagning av diskret PID-regulator, processorkort, motorkort, val av komponenter och sensor för att mäta robotens vinkel mot ett vertikalplan.Roboten kan balansera stillastående, men behöver kompletteras ytterligare med hjulåterkoppling för att kunna balansera medan den kör. Roboten balanserar med mätdata från en mekanisk golvavkännare (potentiometer). Andra sorters sensorer diskuteras också, t ex accelerometer, gyro och optisk sensor..

This thesis work resulted in a template for how the thermal spray process can be controlled through robot programs. The robots today and their programs need to be replaced, therefore a new structure which can be matched with the new robot systems is needed. The work is limited to only concern structured programming on the new robots on Thermal Spray Centre (TC) with the programming language Rapid. The basic data for the program was retrieved from interviews with concerned personnel at TC, from studies on process parameters for thermal spray and from existing specifications at Volvo Aero Corporation (VAC). The thesis work briefly describes the process thermal spray and the four methods used at VAC.

To make wave power more competitive on the market Uppsala University leads projects that examine how to accomplish better efficiency in the production. One of these projects is described in this report and examines whether it is possible to make the production of dovetails more efficient by using an industry robot of type ABB IRB6000 S3 M91. This project is using an already presented working method, from a previous project, which involves that the robot picks up the dovetail and moves against fixed cutting machines where the dovetail will be drilled, threaded and milled. Drilling and threading are the sub operations that will be examined in this project where experiments are made with the presented working method and with equipment from Uppsala University.Experiments show whether it is possible to drill the holes in the dovetail within specifications by using the specific robot and the presented working method. The threading operation is examined theoretically if it is possible to accomplish by using the same working method.

The goal of this Master thesis has on the one hand been to create a simulation environment for robots, where not only the simulations in this work can be performed, but also similar robot simulations, and on the other hand to study regulators that can increase the possibilities of rejecting disturbances on an industrial robot. The robot model used has three degrees of freedom, corresponding to the three main links on ABB:s IRB7600. The simulation environment is created using Matlab, Simulink, and Robotics Toolbox. It is constructed in a general way and can be used for simulations of other robot objects created in Robotics Toolbox. A gain scheduling is added to the LQ-regulator, where the feedback matrix is varied depending on the arm position in the workspace.

This bachelor thesis describes the process of developing a two wheeled robot with activebalancing. The robot is designed to go straight ahead until it reaches a finish line. Then it shallstop to stand still balancing. The workload in the group has been divided according to theprevious individual projects, which are attached. The design of the robot is inspired by theconcept of the Segway.

ITT Water & Wastewater ställer höga krav på kostnadseffektiv produktion vilket är en starkt bidragande orsak till att företaget är världsledande på sin marknad. För att erhålla kostnadseffektiv produktion har kombinationen människa robot visat sig vara framgångsrik.Examensarbetets syfte var att ta fram underlag åt ITT Water & Wastewater för att ta beslut om frigörande av indirekt personal vid line 15:s isoleringsstation på Elmotorverkstaden. Syftets uppfyllande stöttades av de underbyggande syftena att försöka höja robotens utnyttjandegrad samt reducera isoleringsmaskinens omställningstid.Arbetet bygger på kvalitativa och kvantitativa data i form av mätningar, intervjuer och egna observationer. Med stöd av erhållen data lyftes fyra olika förslag fram. Förslagen understryktes bland annat av integrering av arbetsmoment, förhöjd automatiseringsgrad och outsourcing..

This thesis has treated a three-axis robot which task is to serve a larger test machine tomove the modules to be tested, from the storage to the test site. The robot is composed ofthree linear actuators; two standard components of ball screw type and a custom-builtactuator of trapezoidal type. The work has mainly focused on the custom-built device to seeif it could be replaced with a standard component. Part of the work has been to look into thepicking tool and to see if there are any possibilities to improve its function.The report presents two different proposals which I decided to call Robot 1 and Robot 2 andthey aim to address the problems arising in the purpose-built linear unit and the X-axislinearity problems. Robot 1 focuses on eliminating the problems that arise around therobot's X-axis, with such simple means as possible and without making excessive materialchanges.

This field study examined how elderly and cognitively disabled people used and experienced a social companion robot. The following pages explores the questions: Which are the physical, social and affective qualities during the interaction? The aim was to through observations see how qualities of interaction could activate different forms of behavior. The results show that motion, sound and the eyes together created communicative and emotional changes for users who felt joy and were willing to share the activity with others. The robot stimulated to some extent users to create their own imaginative experiences but often failed to involve user or group for a long time and was also considered too large and heavy to handle..

In this master thesis, control algoritms using arm side sensors are investigated for an industrial robot. The sensors can be position encoders placed after the gearbox and accelerometers on the robot arms. Control strategies are discussed and evaluated for different models of the robot, after which chosen strategies are applied to a realistic model. Control algoritms using arm side sensors (LQ, dual-loop and PD-PID) are compared to a PID-controller that only uses measurements of motor position for feedback control. The comparison are done with respect to disturbance rejection, oscillation damping, robustness and tracking performance of a reference trajectory.

Inom 3D-grafik, visualiseringar, spel och VR finns ett behov av måttriktig modellering. Traditionellt så används CAD-program för att uppnå ett exakt eller precist resultat. Men då CAD-program inte utmatar polygonal geometri så fungerar det inte att använda resultatet direkt i tidigare nämnda kategorier. Denna studie ämnar att underlätta måttriktig polygonal modellering i Autodesk Maya genom ett tillägg i form av ett grafiskt användargränssnitt. Effektiviteten av detta mäts genom tidtagning på modellering av CAD-ritningar i polygoner hos en testgrupp både med och utan tillägget samt en kvalitetskontroll där resultatet jämförs med specifikationen.

This thesis deals with the compatibility between analysis software Revit Structure2012 and Robot Structural Analysis 2012. The purpose is to become more aware ofinformation management models to be compatible across different softwareapplications. The structural model is made to be optimal for the compatibility of othersoftware Aim is also to gain an understanding of the transferring methods that exist,and which method is most convenient to use and to examine whether the methodswork in practice. Objective of this project is to make the modeling processtime-efficient for constructors. Models do not need to be structured in severaloccasions in different software; it only needs an optimal model that transfers properlybetween software.The method used in the thesis consist cases where the transferring process isexamined.

Animering i 3d är ett tidskrävande och komplicerat moment som tar lång tid att sätta sig in i. Det krävs att man har en bra känsla för naturliga rörelser för att kunna skapa realistiska animationer. Det här arbetet undersöker möjligheten ett med hjälp av Nintendos Wii Remote-kontroll låta en användare mer intuitivt animera ett enkelt 3d-objekt i Autodesk Maya 2009. Arbetets resultat och slutsatser  visar hur man kan koppla Wii Remote-kontrollens utdata in till Autodesk Maya 2009, och tar upp funktioner man skulle kunna lägga till och vilka begränsningar som behöver lösas i framtida arbete med systemet. .