This thesis describes the redesign ofequipment designed for drying bags thatis used in Fresenius Kabis´manufacturing of their nutritionmedicine in Uppsala. The need of thistask arise during the start of thedevelopment of a new packaging line werethis equipment were meant to be used. Anevaluation of the bagdryers capacity andcapability was necessary.The work started with gathering ofinformation from suppliers of the usedcomponents and from the responsibleengineers for this equipment. Aneducation to learn how the equipmentworked and how to operate it were taken.That was followed by the creation of astudy plan were the tests were plannedto test different parameters effect onthe drying result and to see if thebagdryer managed to handle the bags ofthe correct format in the pace that theequipment should be designed for.The test results detected a need ofdesigning a unit with a function thatholds the bags in place while passingthrough the dryer in order to attainhigh quality results. The results werelater used for optimization of thedesign.

The viscosity of air buildings is a hot topic within the construction performers, which the industry feel they have too little knowledge about. This study is mainly aimed against air density in apartment buildings and airflow measurement. The study consists of a theoretical reference, educational visit, interviews and a survey conducted among construction workers at Magistratshagen in Linkoping.Earlier requirement in terms of air leakage through the climate screen was removed and today there are only energy requirement for a dwelling in Boverkets Building Regulations. The difference between a passive and a typical air tight construction is that the passive house have a maximum requirement of 0.3 l /s m2 of air leakage through the building climate screen. The requirement imposed on passive houses is to minimize the supply of power and energy for heating the building.Air tight constructions have heavy demands on the performance and accuracy of everyone involved with the project. The client must specify their requirements and also be prepared to pay for any additional costs. The architect and building planners have to design the building with regard to air tightness. Finally, the construction workers are required to do a careful work in order to get all the connections in the building air tight.The study suggests that an air tight building is a closed system where no forced ventilation exists. There are no reasons not to build too tight as long as there is a functioning ventilation. In this study the authors ask themselves how an air tight building changes over time. No theoretical information has been found on these changes, but the respondents assume that air density decreases with time. The deterioration is mainly assumed to be caused by construction materials changes over time. The study shows that construction workers knowledge of air tight construction is mixed, which they themselves admit in the survey..

A passive house in Norra Djurgårdsstaden drawn by Tengbom Arkitekter is going to be built. A shaft for airing is needed for a few apartments in the house.The airing shaft is designed for a few two room apartments in the house, which are not able to achieve satisfactory airing, as their outer walls are facing a single direction. The other apartments on the same floor are corner apartments. These apartments do not have the same difficulty with airing since they have their outer walls in different directions, with different pressures at the facades. The airflow in the airing shaft is supposed to be driven only by natural forces, by the sun. The purpose of natural driven forces is to achieve low energy consumption for the house.In this thesis, a design of the shaft for airing has been developed.Initially an open shaft for all apartments was analyzed.

With climate change, the temperature and relative humidity in Sweden are increasing. The majority of historical environments lack protection against this increase, which also increases the risk of mold infestation in these environments. One of these environments is N??s Slott, in which several rooms have recurring mold growth on objects and furniture. By examining one of the rooms in the castle that is in the risk zone or has mold growth, factors behind the mold growth can be investigated in order to create a basis for future actions against mold.

This thesis work has been performed at the department of diagnosis and dependability at Volvo Car Company, Torslanda. The background of this project is based on interest in ascertaining how different factors possibly can affect a diagnosis method, which has been developed to find leaks in the fuel tank and evaporation system. According to the OBD II requirements leaks with an orifice diameter larger or equal to 0,5 mm, must be detected. The idea of the diagnosis method is to create an over pressure in the system with an air-pump. The current through the pump is measured and correlates to the power consumed by the pump.

This Master Thesis is a product development project that has been carried out in cooperation with Scania CV AB. The purpose has been to find the relationship between geometric parameters and the swirl number for an XPI- cylinder head in order to improve the design specification.The increased focus on environmental issues from society leads to tighter emission legislations for the truck manufactures. In order to drive the development forward considerable resources are spent on research and development on diesel engines and its combustion process. The inlet air has a significant impact on the formation of emissions and the flow that is desired is called swirl. Swirl is achieved by making the air rotate around the vertical axis of the cylinder.Earlier cylinder heads that has been developed at Scania CV AB have shown clear relationships between geometric parameters of the cylinder head and the swirl number.

Abstract:This thesis work has been conducted at the Real Estate Department in Halmstad.The department consists of a construction/project management-unit and an operation/management-unit.Like many other towns in Sweden, Halmstad has had a long lasting problem with indoor environment. Not at least at their preschools.Today they are constructing from current building regulations. They have learned from negative experiences which have occurred in the indoor environment in older buildings.Focus is now on healthy materials, like low emission value, energy efficiency and optimization of the building, but still with soft parameters such as cleaning, interior and choice of materials.The fixtures is provides by the real estate department and the furnishings are provides by the children and youth administration. Together they are trying to provide a great indoor environment.I have, together with the real estate department and the children and youth administration of Halmstad, investigated how to provide a good indoor environment in the preschools with small funds.In my thesis there is one theoretical part with a questionnaire survey of how the preschool staff is experiencing their indoor environment to determine where the problems often start. And a practical part with measurements to try and come down to a result that analysis the cause of the problems and also to make sure that the ventilation systems are fulfilling projected values.The measurements and the questionnaire surveys was made at Lokes preschool in Frösakull, Askens preschool in Oskarström and Gullbrandstorps preschool.There were some differences between the staff-responses at the three different preschools.At Askens preschool they feel that the premises are cleaned poorly.At Gullbrandstorps preschool they feel that the indoor-air is bad because they can´t open the windows.

pelago. There is an old inn that is located on the island that has become a very popular attraction in the last couple of years. The inn has both a well-known restaurant as well as conference facilities that are used by tourists as well as the people of Stockholm over the summer months. The inn was built 1908 and has since remained in the same condition.make islands in the archipelago more environmentally friendly and promote sustainability. One of their project islands is Grinda.

This thesis aims at determining the heat losses in a property vent stack and its roof valve. Upon request of a company, the vent stack is analysed for possible heat recovering solutions to be implemented, while relining of the drain system is executed and with a suitable payback time for the economic investments. The heat loss calculations are based on data for properties that are located in the Stockholm region, but also easy to change depending on the situation. The calculations are done on pipes made out of cast iron, which still is the most common type of drain pipe in Sweden, and these are the pipes that relining is usually made on. The calculations that needed to take several variables into account have been done in MatlabR2014a and the thermos dynamical properties that were used in those calculations have been extracted from EES.Three different types of heat losses in the vent stack have been taken into consideration in this thesis.

AbstractElectricity consumption is a globally increasing problem caused by the high share of electricity produced in coal power plants. These contribute to high carbon emissions when only about 1/3 of the heat generate electricity and the remaining 2/3 of the heat cools off. Combined heat and power plants (CHP) have high efficiency because they use the residual heat for domestic heating. The CHP plant often use fuels from renewable resources, giving them a lower carbon footprint, but are also depending on the heat demand. If electric powered products such as drying cabinets convert to heat powered products more environmentally friendly electricity will be produced by CHP plants, which can supplant electricity, produced from coal power plants and reduce carbon emissions.

SUMMARY The interest of horses in the riding sector has increased the last decades. A large amount of horses are transported in a 1 or 2-horse trailer, which is pulled by a car. Today a large number of different products and designs of trailers can be found on the market. The difference in shaping of trailers depends on tradition and experience. There are no detailed directions on the demands for shaping of horse trailers today. The literature review contains a market analysis of both Swedish and imported horse trailers.