This bachelor thesis has the purpose to visualize and document the air movementsprovided by different ventilation principles in an operating theatre. The visualizationwill be made as simple as possible in a physical model. The model and thedocumentation should be able to use in educational purposes.The study is based on the two most common systems for airflow, currently used inoperating theatres. The first principle is displacement ventilation in which the air issupplied at low velocity along the floor. The second principle is vertical parallel laminarairflow in which the air is compressed like a piston from ceiling to the floor.A review of literature resulted in the choice of size, design, and scale factor for themodel, as well as choices of ventilation principles and airflows.

This bachelor thesis has the purpose to visualize and document the air movementsprovided by different ventilation principles in an operating theatre. The visualizationwill be made as simple as possible in a physical model. The model and thedocumentation should be able to use in educational purposes.The study is based on the two most common systems for airflow, currently used inoperating theatres. The first principle is displacement ventilation in which the air issupplied at low velocity along the floor. The second principle is vertical parallel laminarairflow in which the air is compressed like a piston from ceiling to the floor.A review of literature resulted in the choice of size, design, and scale factor for themodel, as well as choices of ventilation principles and airflows.

This masters thesis concerns a modeling project performed at Volvo Technology in Gothenburg, Sweden. The main purpose of the project has been to develop a physical model of the climate in construction vehicles that later on can be used in the development of an electronic climate controller. The focus of the work has been on one type of wheel loader and one type of excavator. The temperature inside the compartment has been set equal to the notion climate. With physical theories about air flow and heat transfer in respect, relations between the components in the climate unit and the compartment has been calculated.

This thesis describes how a cost reduction project was done on the Packsize ondemand packing machine EM7. The cost reduction was achieved by making minorredesigns of the EM7.The project began by studying the EM7´s structure and function by working on itsassembly line. A short literature study on the subject Design for Manufacturing wasalso done.By working on the assembly line and by speaking with staff from production anddevelopment departments, a number of ideas for reducing manufacturing costs arose.Estimations of the potential cost reduction size for each proposal were done incollaboration with vendors and the purchasing department. Based on the size of the cost reduction, technical risk, impact on the assembly lineand the development time the various proposals were ranked. The two highestranked proposals were selected for further development towards finished solutions.One of the ideas that were selected to develop in to a finished solution meant thatsome of the pneumatic valves were replaced with others.

The high viscosity of barley material makes starch isolation problematical using regular methods established for cereals. An adjusted starch isolation method has been set up for barley, based on fractionation and purification. The focus is on attaining truly representative isolates of six flour samples selected for widely differing characteristics within the research program BarleyFunFood (BFF). Beside establishment of the method, this diploma work aspires to serve the BFF with isolated material of sufficient yield valid for further starch characterisation. A pre study was conducted evaluating available wet mixing equipment, experimental conditions and mode of procedure.

A change towards using more biofuels than fossil fuels is taking place in Sweden, and in many other parts of the world. This makes the use of fuel pellets increasingly popular, causing a greater demand for sawmill sawdust products. There is a trend towards the use of multiple types of shredders, instead of a single type in each sawmill. The purpose of the study was to characterize the different flows of saw particles that can be found at Sävar såg when cutting thick or thin wood with different cutting techniques. The saw particles size, shape, moisture content and heat value were analysed by the cutting stations: first cutting fast and slow, second cutting fast and slow, grading fast and slow and planning.

Until the beginning of the 1900:th century the paper making process was handicraft. The paper machines that have been developed since then are as impressing in size as fascinating when it comes to the technique. The process has always been improved to give a better paper for lower costs, with as short manufacture time as possible. Stratified forming has been a reality since 1830. From the beginning it was applied to board and paperboard.

This report is written on the assignment by Nexans IKO Sweden AB in Grimsås which is a cable manufacturing company. Nexans IKO Sweden AB was in need of help to examine possibilities for saving energy by saving compressed air, in first place by using the compressed air more efficient. The task was to determine the present situation, making the airwipe stations more efficient by reducing the consumption of the compressed air and in turn save money. Even the aspects of the working environment were discussed as the noise levels from the pneumatic systems and engines are usually high. A schedule over the airflow in the factory and the inventory over current airwipessituation was made.

Lake Bornsjön is situated 30 km southwest of Stockholm in a rift valley lake and consist three basins outstretched in northwest-southeast direction. The surface area is 6,7 km2 with a maximum depth of 18,3 meters, a mean depth of 9,8 meters and a retention time of the water of 6,5 years. The drainage area is 42 km2 and consists mainly of arable land (ca 1000 ha) and productive forestry land (2500 ha), but in the drainage area there are also restored and fairly newly constructed wetlands.Today the Stockholm area receives its drinking water from Lake Mälaren, but if there would be any pollution of this source, Lake Bornsjön would act as the water source. The area surrounding the lake was bought already in 1899 by Stockholm Stad for protection of the lake and was taken over 1993 by Stockholm Vatten AB. It has been a water protection area from 1988 and it was also accepted as a nature reserve in 1995.

Convective snowbands is a weather phenomenon that is associated with heavy snowfall in a limited area. They are formed over ice-free parts of e.g. the Baltic Sea when there is a cold easterly airflow over relatively warm water. These convective snowbands can cause large amounts of snow along the Swedish east coast, often causing traffic hazards. Sometimes they can even paralyze an entire community.  In this study, convective snowbands that have formed over the Baltic Sea during the period 1980-2009 are examined, in order to find out how often they occur, what place they are most common and in what month they usually appear.

Energy supply in Sweden year 2011 amounted to 577 TWh. The final energy consumption for industrial, residential and service was 379 TWh. Sweden has energy policy goals to reduce energy use in buildings. One of these goals is to reduce the energy use by 20 % in 2020 compared to the year 1995. An important step to achieve this goal is to target energy efficiency measures in existing buildings.

This report was performed in order to evaluate a new technological measure and focuses generally on a heat pump system to a HWC-washing machine. The client is Asko Appliances AB, a company well known for its environmentally friendly products. The goal of this study was to improve the energy efficiency of a washing machine by combining a heat pump device to the heater of the wash water, in order to reduce the energy consumed for heating the water. Besides reducing the energy consumption in heating the water, the washing machine was required to meet low noise and short operating time specifications. For that purpose, nine trials in three test series have been carried out.

This thesis is a product development project that was performed at Alfa Laval Tumba AB. In the past Alfa Laval have manufactured gas separators for engines where gas flows were cleaned from oil. A new business area for this kind of technology has shown to be the manufacturing industry where oil mist has to be separated from the vented air. Therefore a new and bigger design is needed to be able to handle the greater gas flows. A product like that would be a strong competitor on the market when the maintenance would be low in comparison to today?s equipment.During the project several concept suggestions were developed using customer interviews and research as input.

This thesis describes the redesign ofequipment designed for drying bags thatis used in Fresenius Kabis´manufacturing of their nutritionmedicine in Uppsala. The need of thistask arise during the start of thedevelopment of a new packaging line werethis equipment were meant to be used. Anevaluation of the bagdryers capacity andcapability was necessary.The work started with gathering ofinformation from suppliers of the usedcomponents and from the responsibleengineers for this equipment. Aneducation to learn how the equipmentworked and how to operate it were taken.That was followed by the creation of astudy plan were the tests were plannedto test different parameters effect onthe drying result and to see if thebagdryer managed to handle the bags ofthe correct format in the pace that theequipment should be designed for.The test results detected a need ofdesigning a unit with a function thatholds the bags in place while passingthrough the dryer in order to attainhigh quality results. The results werelater used for optimization of thedesign.

In Sweden, grass is the single largest crop grown. Nearly 1 000 000 Ha grows on the fields, this is primarily used as feed for livestock. To get a good seed, you need to handle the crop carefully from planting to delivery. The part that I have been interested in, is how to dry the harvested seed with out destroying the growth in the small seed. This is very easily done if you aren?t careful during the drying period.