In recent years, existing solutions for cooling personal computer CPUs have been supplemented by a new product category, factory sealed water cooling loops. These systems, consisting of a water block with an integrated pump, a fan and a radiator, perform well compared to the air cooling solutions but are less effective than larger, custom-built water cooling systems.This project aims to explore the most important aspects of a factory sealed system and to identify possible cost-effective enhancements of the performance.The most significant differences between the different groups of water cooling loops are the block design and the pumping power. The performance of both categories is also largely dependent on the fan power, but increasing fan power has a large negative impact on the noise level.Both radiator size and fan model choice appear, in tests, to be relatively unimportant, presuming that the noise level is kept constant. The position and direction of the fan, however, has significant impact on both the temperature and the sound level.Water blocks can be designed in several different ways, both regarding the heatsink design and the flow direction. In simulation, flow with the inlet centered above the heatsink result in considerably lower pressure drop and slightly higher temperatures than flow through the block, for heatsinks with fin arrays.Creating a competitive product in this product segment certainly seems possible, as there are performance-increasing changes to be made that seemingly has little impact on the production cost.

Gunsta is situated about 10 km east of Uppsala. Today there are plans to establish 1000 new households in Gunsta before year 2030. The required energy for heating houses and water would be distributed via a district heating system, which also includes 200 existing residences. The annual required energy, according to this study, would be 16.2 GWh with a maximal peak effect of 6.9 MW. To meet this need, the study suggests a system with heat pumps to upgrade the 31?C water from a 1.8 kilometre deep borehole.

The company Olofsfors AB manufactures drive belts for forest machinery, known as ECO-Tracks, and abrasion-resistant steel and cutting edges for graders, excavators and tractors, known as Bruxite and SharqEdges. Manufacturing these products requires the steel to be heated and molded, then submerged in water and hardened. The water used in the hardening of steel is pumped to the process from pits below the floor and then pumped back to the pit after it?s been used. Since the temperature of this water rises after being used to harden the steel the temperature of the pumping pit needs to be adjusted to maintain its setpoint of 21°C.

The company Olofsfors AB manufactures drive belts for forest machinery, known as ECO-Tracks, and abrasion-resistant steel and cutting edges for graders, excavators and tractors, known as Bruxite and SharqEdges. Manufacturing these products requires the steel to be heated and molded, then submerged in water and hardened. The water used in the hardening of steel is pumped to the process from pits below the floor and then pumped back to the pit after it?s been used. Since the temperature of this water rises after being used to harden the steel the temperature of the pumping pit needs to be adjusted to maintain its setpoint of 21°C.

The company Olofsfors AB manufactures drive belts for forest machinery, known as ECO-Tracks, and abrasion-resistant steel and cutting edges for graders, excavators and tractors, known as Bruxite and SharqEdges. Manufacturing these products requires the steel to be heated and molded, then submerged in water and hardened. The water used in the hardening of steel is pumped to the process from pits below the floor and then pumped back to the pit after it?s been used. Since the temperature of this water rises after being used to harden the steel the temperature of the pumping pit needs to be adjusted to maintain its setpoint of 21°C.

Geothermal energy can be extracted from an aquifer, where the groundwater is used as heatexchange medium while heat and cold are stored in the surrounding material in the aquiferand to some extent in the groundwater. Application of aquifer storage for the use ofgeothermal energy is mainly used in large scale facilities and is limited to sites with suitableaquifers in the form of ridges, sandstone and limestone aquifers.Löwenströmska hospital in the municipality of Upplands Väsby, north of Stockholm, islocated nearby the northern part of the Stockholm esker. This means that it can be profitableand environmentally beneficial for the hospital to examine the possibilities of aquifer storagein the esker material next to its property.The purpose of this master thesis has been to investigate if geothermal energy storage with aseasonal storage of heat and cold can be applied within Löwenströmska hospital?s propertyarea using groundwater modeling. A hydraulic groundwater model was constructed inMODFLOW based on a simplified conceptual model of the groundwater system.

In order to facilitate testing of anesthesia machines a patient simulator has been required by Maquet Critical Care AB. A patient simulator has been developed to reduce expensive and time consuming animal experiments and temporary lab arrangements. The patient simulator has been developed and designed to simulate human lungs with regards to anesthetic uptake, production of carbon dioxide and heating and moisturizing exhaled air.The system comprises a container and a test lung to simulate the volume and the dynamic of the human lung. The simulation of uptake of anesthetics has been implemented by pumping a fraction of the gas from the container through a bypass circuit with an active charcoal filter that adsorbs volatile anesthetics. The flow through the bypass circuit is generated by a pump and is controlled by a linear valve.The resulting performance of the patient simulator has fulfilled the requirements.

Water is the most essential resource for life. In cases where drinking water is processed from surface water it is important to ensure the raw water is of good quality, and is suitable for processing through the water treatment plant.The drinking water for Västerås is sourced from Västeråsfjärden, in the western side of Lake Mälaren. The city itself is home to marinas, ports, a wastewater treatment plant, the Svartån outlet, sewage pumping stations and stormwater outlets. Because of the negative effects these activities have on surface water quality, Mälarenergi AB is interested in relocating the raw water intake point to Granfjärden, 10 km east of Västeråsfjärden. At Granfjärden the intake point would be less exposed to the activities in Västerås, and could be placed at a greater depth, resulting in better water quality.In this Master?s thesis the water quality and the pollution risks at Västeråsfjärden and Granfjärden sites are compared.

Krav om förbättrad spillvattenrening och städer som förgrenar sig över större områden är några av anledningarna till att dagens avloppsledningsnät får allt längre ledningssträckor. Att med gravitationens hjälp föra avloppsvatten framåt kräver ett kontinuerligt fall som vid långa avstånd kan innebära mycket schaktning, den ekonomiskt mest belastande delen vid nyinstallation av avloppsledningsnät. Ett fördelaktigt alternativ kan vara trycksatt avloppssystem, som sedan 70-talet har kompletterat de traditionella självfallssystem i kuperade och bergiga områden. På senare tid har trycksatt avloppsystem fått större användningsområde utanför sina etablerade bruksområden med anledning av skärpta krav på rening och kostnadseffektivitet. Självfallssystem är dock det mest använda avloppssystemet i urbana områden.

Estimation of the variation in the integrated hydraulic conductivity around the Tunåsen infiltration facility - An investigation of the effects of uncertainties in existing informationAlmost half of Sweden?s drinking water volume is produced from groundwater. The main fraction of this is extracted from eskers, some of which allow for very large extraction rates. Despite this, the groundwater volume is not sufficient in some areas. This has led to an extensive use of artificial recharge.In Uppsala, the total volume added through artificial recharge is divided between four infiltration facilities.

Lake Bornsjön is situated 30 km southwest of Stockholm in a rift valley lake and consist three basins outstretched in northwest-southeast direction. The surface area is 6,7 km2 with a maximum depth of 18,3 meters, a mean depth of 9,8 meters and a retention time of the water of 6,5 years. The drainage area is 42 km2 and consists mainly of arable land (ca 1000 ha) and productive forestry land (2500 ha), but in the drainage area there are also restored and fairly newly constructed wetlands.Today the Stockholm area receives its drinking water from Lake Mälaren, but if there would be any pollution of this source, Lake Bornsjön would act as the water source. The area surrounding the lake was bought already in 1899 by Stockholm Stad for protection of the lake and was taken over 1993 by Stockholm Vatten AB. It has been a water protection area from 1988 and it was also accepted as a nature reserve in 1995.