This study was made as a part of a feasibility study on a polishing wetland at Rimbo wastewater plant (wwp) in Norrtälje municipality. The wwp had to decrease the nitrogen discharge to reach the limit 15 mg tot-N/l. The nitrogen in the outlet was mainly in the form of nitrate, hence the wetland mainly ought to support denitrification. The proposed area for the wetland was situated right next to the wwp and was already in the municipalitys posession. One aim of this study was to examine what spieces of plants needed to achieve highest possible denitrification.

Periods of hypoxia are a recurring issue in Brunnsviken. Main factors that trigger hypoxia in Brunnsviken are eutrophication  due to anthropogenic emission of nutrients, stratification in the water column due to salinity and temperature differences  that prevents mixing and a sill inlet that prevents water exchange. As an attempt to improve the oxygen levels, bottom water is pumped from Brunnsviken causing aerated surface water to flow back into the basin.  The objective of this Master?s thesis was to study the change in dissolved oxygen levels due to pumping.

I was assigned to the thesis as part of a project GMA AB (Ground Machinery Applications AB) is running. The project aims to develop a new method for injection of drilled holes in rock walls. Currently, the injections usually involve cement but the basic idea of the project is to replace cement with a supplement called Silica sol.Silica sol is known as a gelling liquid. The gel time is controlled by a mixing of saline. Depending on the amount saline that gets mixed in, the gel time varies.

When establishing a groundwater protection area it is of great interest to be able to estimate the transit time of the groundwater from different places of the aquifer to the withdrawal well. These estimates can be uncertain due to heterogeneities in the aquifer. As a part of the work to develop methods for a more certain delineation of protection areas, a tracer test was performed in an esker located 25 kilometres NW of the town Uppsala.The purpose of this master thesis was to perform, describe and evaluate the tracer test. Travel times from the tracer test should then enable comparison against stochastic simulated travel times of the groundwater in the area.Three dyes (rhodamine WT, uranine and naphtionate) and a salt (NaBr) were used in the tracer test. The tracers were injected in four different wells located 25 meters from a pumping well.

The aim with my master thesis is to develop and test the applicability of methods to quantify and map solute advective travel times and pollutant transport at the catchment scale. Such quantification and mapping can increase the understanding of catchment-scale pollutant transport in general and contribute to the identification of the main sources of water pollution and the most efficient measures to reduce such pollution. The study area is the catchment of Oxundaån, about 20 km north of Stockholm. For detailed GIS modeling of water flow and catchment-scale contaminant transport in water, I´ve used new high-resolution elevation maps, land cover maps and soil maps combined with other available relevant data..

A study has been performed that investigates the variation of iron content in groundwater.The study was initiated by Midvatten AB, which noticed that the iron content in groundwater samples can vary greatly over small distances. The purpose of this study was to geochemically and geohydrologically determine the factors that influence the content of iron and manganese in groundwater from a selection of eskers in Dalarna, and determine how to best sample groundwater with the method used by Midvatten AB. An evaluation was made of how the vertical variation in soil material, water composition, pumping time and pipe material affects the content of iron in groundwater. Piper diagrams were used to study the relationship between the chemical composition of the groundwater and the content of iron and manganese in groundwater samples from the studied areas. The groundwater from the studied areas was then classified in the Piper diagrams, according to the content of the major ions.

Shock absorber units play a key role in establishing the driving dynamics and performance of automobiles. Öhlins Racing has manufactured high-tech automotive shock absorbers for over 30 years. Öhlins Racing?s advanced technology has contributed to over 200 world championships in automobile racing. Öhlin?s manufacturing process has long utilized automated fluid filling equipment during the final shock absorber unit assembly stage. The filling process consists of vacuum pumping the shock absorber unit and subsequent transfer of fluid. Vacuum pumping is necessary to remove residual air from the shock absorber unit prior to initiating the liquid filling stage. The presence of undesirable gases drastically compromises the performance of a shock absorber. The filling degree, defined as the final ratio of air to oil, is determined by the specific filling protocol as well as the specific equipment utilized.The current investigation aims to develop a viable technique to accurately determine residual air content in shock absorber units. If the filling degree can be appropriately quantified for a specific manufacturing process, then the air/oil ratio may be quantitatively related to shock absorber performance. The utilized measurement method must be completely integrated into the manufacturing process to guarantee shock absorber performance specifications according to the manufacturer?s standards. By utilizing the measurement method developed in this work, the manufacturing process, manufacturing equipment and product specifications can all be tailored to provide improved filling conditions.The developed measurement method provides accurate quantification of the filling degree under a wide range of processing conditions. The method establishes the relative quantity of air in the shock absorber unit by performing in-situ compressibility tests. The fill ratio can be controlled and varied by manipulating the vacuum pressure exerted during the filling process. Performance tests, however, indicate no correlation between filling degree and unit performance..

When protection zones for wells are delineated, it is important to acquire good knowledge about possible travel time from different points in the catchment area to the well. Often, simple analytical methods are used for estimating travel times and the assumption is made that the hydraulic conductivity is relatively homogenous within the aquifer. Nevertheless, many aquifers are strongly heterogeneous which may lead to differences between estimates and actual travel times. As a part of the process to develop improved methods for delineating protection zones for groundwater supply wells, a tracer experiment was performed in a glaciofluvial esker formation in Järlåsa. On the basis of the experiment, a numerical flow model was created for the test site.The purpose of this master?s thesis was to apply the flow model to an aquifer where the hydraulic conductivity shows great variability and should be described by a stochastic distribution.

Over an extended period of time there have been plans to establish a shared facility in Lennheden to extract groundwater from the Badelunda esker to provide drinking water for the cities of Borlänge and Falun. The city of Falun is dissatisfied with the quality of its drinking water and the city of Borlänge is concerned about the risk of contamination of its existing groundwater supply at its current location. To provide a basis for a decision on this issue, the company Midvatten AB has been commissioned to perform hydrogeological investigations in the area of Lennheden.The purpose of this thesis is to design a functional groundwater model of the area between Lennheden, place of planned extraction, and Övre Tjärna, place of existing extraction, to get a better understanding of the groundwater situation in the area. A groundwater model enables simulations of different scenarios in risk assessment and contaminant transport. The aim of the thesis is that the model can be used as an aid in Midvatten?s investigations in Lennheden and that it also can be used in future projects in the area.The model has been made in Processing Modflow 5.3 and encompasses an area of 19,5 × 11 km along the Badelunda esker and the river Dalälven between Djurmo and Frostbrunnsdalen.

In modern society in terms of economics and environmental impact, it is important to ensure that a company is as energy efficient as possible to reduce the amount of energy used. About 10 TWh of electricity used annually to pump drives in Swedish industry. Therefore, pumping system has great potential for energy savings.The objective of this report was to determine how much energy and money that can be saved with the insertion of variable speed drive to six pumps on Bleach plant 4 in Skutskär Mill. The work was performed with electrical measurements during one week, analysis of pump curves and the compilation of production data over a year.The results show that four of these six pumps were profitable and yielded an annual saving of 1172 MWh of electricity and 560 000 SEK. With an economic lifetime of 10 years and a discount rate of 6.8% the final result for the entire life-cycle savings became 3 355 000 SEK.

This thesis work has been carried out at the consultant company Pöyry Sweden AB in Norrköping, whom performs the task for E.ON heating Sweden AB, Händelöverket in Norrköping. The report shows methods to manufacture slurry consisting of fly ash and water. The slurry shall be pumped into several former oil storage rock shelters that E.ON has put into operation for the specific purpose. The ash mixture also develops hydrogen gas in contact with water.The work has aimed to produce different suggestions of methods and equipment that can be used for the objective. Mixing method and security issues were in centre while working with the suggestions.

ABB I-R Waterjet Systems combines the robotics and motion expertise of ABB Flexible Automation with high-pressure intensifier/pumping technology from Ingersoll-Rand to provide and continue to develop innovative waterjet cutting systems for global markets. The purpose of this assignment is to develop a process water purifier. The purifier should be applicable as an option to ABB I-R?s production cell Cutting-Box. At first hand the process water should be purified well enough to let out in the municipal sewage system, but the ultimate solution is purifying the process water to the range that recycling is possible.

ABB I-R Waterjet Systems combines the robotics and motion expertise of ABB Flexible Automation with high-pressure intensifier/pumping technology from Ingersoll-Rand to provide and continue to develop innovative waterjet cutting systems for global markets. The purpose of this assignment is to develop a process water purifier. The purifier should be applicable as an option to ABB I-R?s production cell Cutting-Box. At first hand the process water should be purified well enough to let out in the municipal sewage system, but the ultimate solution is purifying the process water to the range that recycling is possible. When investigating the different principle of purifying water, a research of different products and their manufactories was done. These different products were compared and the principle of filtration was the most applicable, as most of the products were designed for far larger applications. As the process water contains quite large amount of particles, it is necessary to perform the filtration in different steps. The process water purifier is therefore composed of a module of coarse filtration and one of micro filtration. In the module of coarse filtration the mainly amount of fibres and particles are eliminated. They are kept back in the container unit with the larger fragments and dumped with these when the container is emptied. In the module of micro filtration the filtration is performed in two steps. In the first step particles larger than 50?m are eliminated, in the second step the micro filter is setting the range of purifying, in this case 10?m.

The project was performed at SiemensIndustry Drive Technologies with theobjective to provide actual values forthe energy savings potential withinSiemens scope of practice.In Sweden the electrical drives standfor about 30 % of the total electricityconsumption and about 60 % of theelectricity consumption within theindustry. During the pre-study phaseelectrical drives with pump applicationswere identified as large energy users.Because of this a case study at one ofSiemens customers, Stora Enso Fors wasperformed. The system that was evaluatedduring the case study was a throttledsystem with a centrifugal pump forpumping pulp.The results yielded that a saving ofover 50 % could be achieved by replacingthe throttle valve with a variable speeddrive, a frequency converter. Thepayback period was two years and twomonths and the present value for thetotal life cycle cost of the variablespeed system was 662.566 SEK lower thanfor the throttled system. As aconsequence, Stora Enso Fors is advisedto invest in a frequency converter forregulation of the system.The general conclusion is that a focuson system efficiency is the mostimportant factor in energy efficiencyprojects and that the system regulationmethod has a large impact on the overallsystem losses and hence its efficiency.Energy efficiency potential forthrottled systems with centrifugal pumpsis large and significant economicalsavings can be made through investmentswith short payback time..

Transdermal drug delivery, besides painfulinjections with syringes, has long been associatedwith small size particle pharmaceuticals, which candiffuse through the skin. This method of drugadministration has only been applicable on a smallnumber of drugs, where active molecules are smalland delivery time should or can be long.Other drug delivery options are oral administrationand injection with hypodermic needles (ordinaryhospital syringes). In oral administration thestomach and liver tend to dissolve the drug and theeffect becomes more difficult to anticipate, anddrug delivery rates difficult to control. Hypodermicneedles are used as a mean of drug injectiondirectly into the bloodstream. This method ispainful and risks infection due to tissue damageand skin penetration.One way to get a painless non-damaging techniquewith high delivery rate that still can delivery largemolecules is to manufacture an array of microscopichollow needles and equip them with a pumping unitthat delivers the correct amount of drugs.This thesis shows the technique and possibility ofmanufacture micromachined needles using low costtechniques of Ion Track Technology (radiation ofheavy ions creates porous materials), electrolessdeposition (non-current activated wet chemistrymethod of depositing metal) and electroplating.