The survey aims to shed light on traditional and contemporary bottom floor frames, their construction and different insulating materials; mineral wool, wood shavings and charcoal. The purpose is to analyze and discuss the similarities and differences as well as the pros and cons with a focus on the construction and the different insulating materials. The work has been limited to comparing two different wooden floor frames. The first one is based on a real floor frame from an older building, this example is presented as the traditional floor frame in this study and are from around 1940. The other floor frame is presented as a contemporary floor frame and is based on wood building type descriptions and literature.

The construction industry has been heavily criticized in the past few years for its development of productivity compared to the manufacturing industry. In 2009 the Social Care Center developed a report that treated och criticized different errors within the construction industry. For instance competence, construction errors and performance had showned bad results which had to be improved. A common sentence within the building industry is that ?every project is unique?. Today it?s common for a construction company to have costs for material and services which exceeds two-thirds of the total cost.

AbstractAccording to research made by Statistics Sweden on the members of the labor union IF Metall the number of reported musculoskeletal disorders for employees working under the collective bargaining agreement for the automotive industry has almost doubled since 2003. During 2004- 2006 and 2008 male assembly workers were the occupational group with the highest amount of reported work related disorders in Sweden. To prevent musculoskeletal disorders is according to Rose and Orrenius important both for the individual, the society and the industry by reducing economic and personal costs. The purpose of this paper is to identify and analyze how the manufacturing industry is affected by musculoskeletal disorders that occur when working with line assembly and how companies can prevent them. The report aims to provide the reader with an understanding of what musculoskeletal disorders are, to which extent they occur in assembly, how companies are directed by laws and regulations and how they affect the Swedish manufacturing industry and their employees.

Within process or manufacturing industries, the production of goods and services or the products themselves may have negative side effects such as pollution. An important task for environmental policy is to control and limit these pollutions, for example via regulatory measures. Although, the efficiency of such measures vary greatly between different industries and an increasingly important task for environmental policy is then to encourage companies to engage in environmentally motivated innovation. Governments can utilize other measures than regulation to indirectly decrease pollution. This thesis aims to analyze such activities and how it affects the innovativeness of wastewater treatment, refrigeration and automobile manufacturing industries.

Rapporten beskriver arbetsgången vid utvecklingen av ett kompressorkit till Yamahas snöskotermodell RX-1. Arbetet innefattar konstruktion och dimensionering av tryckkammare och laddluftkylare. Datorverktyg i form av CAD (Computer Aided Design) och FEA (Finite Element Analysis) har använts till att konstruera och dimensionera ingående komponenter. Arbetet har resulterat i kompletta CAD-modeller av ett prototypkit färdigt för CAM- beredning (Computer Aided Manufacturing) och tillverkning..

The work thesis was performed at Assalub a company which is situated in Åtvidaberg. The company works with developing, manufacturing and marketing equipment for handling of lubricants for light and heavier industry. The work thesis it is based on a inquiry Assalub got from MacGregor which is a company within cargo solution, from port to offshore system.For unloading grain and other material from the ship cargo it is used combined inlet feeder and screw conveyor, there the inlet feeder is drilling down through the cargo and feed the screw conveyer with material to further destination. At the bottom of the screw conveyer and the inlet feeder there is a bearing that keep the parts together. However the lubrication of the bearing must be made manually.

Quality can be defined as the ability of a business to satisfy their customers? needs and expectations. Total Quality Management is defined as the way to prevent, appraise and improve the entire organization to increase the product quality. In order to systematically increase quality in an organization, there are different quality systems in use. One example is process management, which is to divide the activities of processes.

A manufacturing machine at the engineering company Sandvik Coromant has a positioning table which task is to move an item linearly. The positioning table has a linear motor capable of high velocity and acceleration. This makes it possible to achieve short cycle times and a more profitable production.The purpose of this thesis is to bring forward a new concept which is more adapted to the requirements of the positioning table. The reason is that the current positioning table provides an unnecessarily positioning accuracy of 0.01 mm, while the requirement for the positioning accuracy is just 0.1 mm. The goal is to reduce manufacturing and component costs.To develop a suitable solution an approach for the concept development process has been performed.

This study was conducted at Glimek AB, a company that has chosen to decentralize its central storage unit in order to increase production efficiencies. The purpose of the study was to identify the problems in the production cycle that lead to the decision to decentralize the central storage unit, as well as identifying what the decentralization entails. The effects of the decentralization have not been analyzed in the study, and consequently neither financial nor production disadvantages have been considered.Appropriate questions were formulated based on the chosen underlying theories, and were asked to selected individuals with relevant knowledge. The study is based on the information that was gathered from interviews with management as well as staff within the company. In addition, supporting information such as flowcharts, drawings, orders and decision support documents were supplied by the company.

High demands are set on all equipment used in emergency service work, where small margins can be the distinguishing factor between life and death during a rescue operation. It is important that tools such as ladders quickly and easily can be dismounted from a vehicle and still satisfy the regulatory requirements for securing loads during transport. The existing solution for getting ladders down from the roof of a fire engine requires a large manual effort from the user in an ergonomically unsound posture.In this degree project a new ladder holder is developed with focus on the user to solve the ergonomic problems and at the same time create a more compact design that can be adapted to several different types of ladders. After an initial pre-study with user-interviews and measurement of forces and distances a set of requirements was formulated that came to govern the project's direction. Creative methods were used to generate concepts that improved the function and through design solutions, calculations and testing in CAD a base for manufacturing of a new product was created.The result is a completely new type of ladder holder that minimizes the user's manual effort and simplifies the securing of ladders in the holder.

This Master Thesis is a product development project that has been carried out incooperation with Metso Paper Sundsvall AB. The task has been to develop a holdingsolution that generates force between two rolls and to evaluate the new solution withrespect to functionality, manufacturing, structural stability, costs, assembly etc. Theroll holding solution is a system that is part of a rollpress. The rollpress is used towash and dewater pulp. The existing solution creates forces that have to be absorbedby the gable of the press.

This study looks into the possibility, and profitability, of expanding a pilot project that has been put into action at GGP Sweden AB in Tranås, a manufacturing company that produces front mowers. The pilot project is meant to give GGP Sweden AB a more precise control of the flow of goods from their suppliers, and its essence has proven to be quite similar to the Japanese Just-in-Time philosophy.The study has been divided into four separate areas; mapping, supplier selection, supplier evaluation and cost analysis. These areas represent a holistic perspective on the expansion of the pilot project and cover topics varying from methods of finding suitable JIT-suppliers, constructing Key Performance Indicators (KPI) to reviewing costs and assessing profitabilities.In this report, the reader will initially take part in the works of mapping GGP?s manufacturing unit, pilot project and supplier base, which results in a list containing the most suitable suppliers for a Just-in-Time based collaboration. Afterwards, the reader will be led into the area of supplier evaluation, where five KPI?s are created with the purpose of ensuring that GGP will be able to evaluate their suppliers and pilot project in an effective way.

Today small metal parts are mass-produced as for example rollers in cylinder bearings. At high velocity cutting the metal is cut with a great force in a scissor-like device. Both precision and repeatability is important to be able to guarantee good quality, but from an economical point of view it is also important to keep a great manufacturing capacity. The part of the process that is most time consuming is when the metal bar, that is about to be cut, is fed to the right position. Therefore it is interesting to examine if the time used for positioning can be reduced.

Nowdays an efficient production is critical to achieve for companies competing on the market for steel cutting tools. One of such companies is Halmstad based Tooling Support Halmstad AB that manufactures threading-taps, threading-dies and parting off tools, towards a centralized warehouse in Schiedam, Holland. The large amount of different products, approximately 2500 is a big contributor to the problem along with a new order system that creates a demand of low setup times. Previously the company was forwarded orders through quarter based prognoses which enabled planning of the production over a longer time span. Currently the newer order system ZENIT is in use and the company thereby gets their orders weekly.

Continuous improvement is one of five principles in General Motors ? Global Manufacturing System (GM-GMS). GM-GMS has been used by Saab Automobile AB since 2003 and is a central component for realisation of GM?s vision. Internal audits have discovered problems with one of the tools, practical problem solving (PPS), which needs to be improved.