In Peter Weiss debut Fra?n o? till o? (1947) the ?I? travels from island to island as a castaway. The island here can signify, or work as a synecdoche for exile and the feeling of isolation that exile often induces. But the movement from island to island also implies a restless state: Peter Weiss shifting from painting to writing to filmmaking and theatre, from German to Swedish and then back to German. The years during exile and the years that followed the exile until his breakthrough in Germany with Schatten des ko?rpers des Ku?tchens (1960), Abschied von den Eltern (1961) and Fluchtpunkt (1962), were the formative years of Peter Weiss authorship.

Resignations are common in all business sectors and can also be found among forest machine operators in the forest business. As the industry today faces a lack of forest machine operators it is justified to determine why machine operators choose to quit their jobs. The aim of this study was to a) find out the number of machine operators that have resigned b) identify and analyse the cause for these resignations c) identify the reasons why the machine operators started to work in the forest and d) give suggestions on different measures that will limit resignations amongst forest machine operators. A questionnaire was sent to machine operators who have quit working as employees, contractors or as employees for contractors with Holmen Skog during 2003-2007. 32 machine operators responded to the questionnaire. Interviews were made with 10 machine operators who had answered the questionnaire to gather more qualitative data. The results of the study indicate that fewer forest machine operators change profession than employees in other occupations in Sweden.

Statistiska Centralbyrån (SCB) samlar in data i form av enkätundersökningar. Dessa data måste sedan kodas med olika klassifikationer för att kunna användas i statistikproduktion. En sådan klassifikation är Socioekonomisk indelning (SEI).Denna rapport behandlar hur man automatiskt kan SEI-koda sådana enkätundersökningar så att varje enkät tilldelas en SEI-kod. SCB:s nuvarande algoritm kodar ca 50% av enkäterna och bygger på att det yrke som är angivet i enkäten finns med i ett lexikon. Om yrket inte finns med kan enkäten inte kodas.

Vertical hydropower units has a rotating mass of up to 1000 tons. For the generator and turbine to work well the rotating system is required to be centered in relation to the surrounding structure. This is achieved by means of radial bearings. The dynamic characteristics of these bearings have a strong impact on the overall rotational dynamics of the total system and thus influence the vibrations in the unit. At Vattenfall Research & Development in Älvkarleby ongoing research is taking place on how the bearing parameters should be represented in the rotor dynamic calculations.

The aim of this project has been to raise the production efficiency of Daliff Precision Engineering through reduced transportation time and a more standardized manufacturing process. The problem has upraised because of a big and diversified product flora without any standard products and with just small batches ordered. The report also tries to show the work procedure with general analytical methods and be an example of how a similar problem can be resolved. The transportation time is being proposed to be reduced through a change in the layout of the factory. By moving a few manual machines, dispatch and burring to more efficient locations, the total transportation time will be reduced by 55 %.

With focal point on the national directions, created by Länsstyrelsen (Swedish county administration) in cooperation with National Method support against Trafficking (NMT), this paper aims to depict the phenomena trafficking and also portray the concurrent counteracting against trafficking in Sweden that authorities exert. All involved participants in this mechanism have their particular remit and their ability to interact is hence of utmost significance.In order to fully comprehend and be able to analyze these unified operative execution-elements and processes in Sweden we also have to understand what is proceeding in the international arena. The organized crime-combine is not restrained by boundaries and continuously develop and refine methods in sexual trafficking, that has grown into an expanding multibillion industry. International counteracting is consequently a worldwide existing matter of utmost interest. Therefore we will also, in our report, present international machines such as International Organization for Migration (IOM).In regard to the proceedings in the international arena, concerning empirical and methodical techniques and information of research findings, the International Organization for Migration (IOM) occupies the leading place in the analysis.The main focus, the cornerstone of this paper, is an inquiry into the formerly relatively unknown and unexplored aspects of what happens to individuals who have been subjected to sexual trafficking in Sweden after governmental intervention implicating forced re-allocation to the country-of-origin.

In 2006, Stora Enso Skog implemented an education program in water management for harvester operators, timber purchasers, cut block planners and supervisors. The focus of the program was creating stream crossings with minimal harm to the stream and the surrounding riparian area. This main purpose of this study was to determine the difference in work procedures before and after participating in the program. The methodology consisted of field studies and interviews with harvester operators and their supervisors. The field study looked at how the streams had been crossed concerning the number of crossings, visible damage to the stream and/or the riparian area made by the machines. Biological parameters such as the width and dept of the stream and amount of large woody debris in the stream were also measured. The field result from 30 harvesting sites showed no significant difference between sites that had been harvested before or after the education program. But the harvester operators and their supervisors experienced an increased concern for watersheds after the educational program.

Problem: The corrugated board industry is highly affected by customer uncertainty, various demands and short delivery times. In combination with a complex multi-step production process managers have to be able to identify bottle-necks and gain knowledge and understanding of how different changes in process will affect the production output. <br/><br/>Purpose: The purpose of this master thesis is twofold, (1) to examine applicability of complexity theory through agent-based modelling on a production process (2) to identify improvement areas in order to increase the production output at SKS production site in Eslöv, by modelling and simulating the production process through an agent-based model. <br/><br/>Method: The chosen method of this study is a combination of a case study and a complex system approach. The empirical data was collected through interviews, observation and document studies which were analysed through an agent-based simulation model.

This thesis has treated a three-axis robot which task is to serve a larger test machine tomove the modules to be tested, from the storage to the test site. The robot is composed ofthree linear actuators; two standard components of ball screw type and a custom-builtactuator of trapezoidal type. The work has mainly focused on the custom-built device to seeif it could be replaced with a standard component. Part of the work has been to look into thepicking tool and to see if there are any possibilities to improve its function.The report presents two different proposals which I decided to call Robot 1 and Robot 2 andthey aim to address the problems arising in the purpose-built linear unit and the X-axislinearity problems. Robot 1 focuses on eliminating the problems that arise around therobot's X-axis, with such simple means as possible and without making excessive materialchanges.

The work presented in this report is written at IEIs department on Linköping Institute of Technology. The report aims to increase the assembly efficiency at Wigells AB. The report shall be used as a guide for the implementation of changes at other workstations in the company. Together with Träcentrum in Nässjö, Wigells AB has identified the needs of this study and contacted IEI at Linköping Institute of Technology.In order to implement an efficient assembly line at the company, studies on lean production have been made. This theory has been studied and together with our own views and findings at the company we have analyzed the assembly area.Wigells is a small company that manufactures wood furniture.

This thesis has treated a three-axis robot which task is to serve a larger test machine tomove the modules to be tested, from the storage to the test site. The robot is composed ofthree linear actuators; two standard components of ball screw type and a custom-builtactuator of trapezoidal type. The work has mainly focused on the custom-built device to seeif it could be replaced with a standard component. Part of the work has been to look into thepicking tool and to see if there are any possibilities to improve its function.The report presents two different proposals which I decided to call Robot 1 and Robot 2 andthey aim to address the problems arising in the purpose-built linear unit and the X-axislinearity problems. Robot 1 focuses on eliminating the problems that arise around therobot's X-axis, with such simple means as possible and without making excessive materialchanges.

AbstractThis thesis is the final part of the Innovation and Design Engineering Programme (180 ECTS credits)at the Faculty of Health, Nature and Engineering Science at Karlstad University. The extent of thisthesis is 22.5 ECTS credits and has been performed independently by Hannes Jernberg during thespring of 2013. Metso Paper Karlstad AB is the task maker of this project, and Arvid Johansson is thecompany Representative. Metso Paper Karlstad AB is one of the world leading developer andmanufacturer of tissue paper machines.In the current situation, the company has developed and patented a power management systembased on a Cross Flow Turbine. The current construction is limited to a paper width of 2.9 meters.The company wants to take advantage of all the opportunities provided by the patents, to develop aturbine solution paper machine with a paper width that is wider than 5.5 meters, and give the abilityto manufacture paper for lower energy consumption which is an important part of the production asit is very energy intensive.Problems arise with the increasing length of the turbine, ultimately resulting in that the deflectionbecomes too big and that the momentums, due to the increased torque the turbine blades breaks.By applying the design process, this work has resulted in a number of potential solutions to theproblem.

This thesis is about developing a design that provides improved vacuum seal between a lead coating and a plastic coating during plastic extrusion processes of cables. This report is a part of the course MSGC 17 for Bachelor Engineers in mechanical engineering.The work is performed at Nexans Norway AS in Halden where they have a production of high voltage cables for sea-, and offshore industry. A problem they face is that they do not get enough good seal at the attachment to the plastic extrusion machine. They want to achieve a vacuum between a lead coating on the cable and a plastic coating of the cable for plastic extrusion, which is something they do not achieve today. The thesis is thus to come up with a design that provides better sealing against the cable.The work involves a construction part with the phases of product development processes.

The development within the textile industry is always ongoing with development of new andbetter textiles, which often mean the use of non-natural materials like polyester. This doesn?t lineup with the work shared around the world against an improved environment, so the idea came touse a form of linen fibers instead of polyester as the reinforcing material together with cotton.The idea was to use flax, linen of low quality, which is seen as a waste product and garbage inthe production of high quality linen and flax seed oil. This flax of low quality needs to beseparated before it can be used in cotton spinning machines. Fireball 2 is just that, a process toseparate flax fibers through the treatment of a technique called electrohydraulic discharge.The thesis works goal is to evaluate the Fireball 2 process ability to separate flax fiber.

This report is the result of a thesis carried out at the Department of Innovation, Design and Technology (IDT), at Mälardalen University on behalf of ABB AB Machines.The year was 1988 when ASEA and Brown Boveri formed a joint venture under the name ABB (Asea Brown Boveri).We perform our thesis at the division Discrete Automation and Motion where they primarily develops, manufactures and sells synchronous and asynchronous AC motors and generators.The main purpose of this thesis was initially to write a general packaging instruction, but the priority changed to develop more specific packaging instructions for Rotors, Stator gables, Bearing support and Outer Cover (plates) instead.The work started off to deal with a problem about that the staff had to start its work to grind away rust on the stator gables due to those stored outdoors. The result was mainly an investment in a new gable rack so that the material can be stored inside, as well as a packing instruction as it was originally intended.The problem on the bearing supports were that the staff thought it was demanding and difficult to clean them from the rustproofing they were greased in. If it is not possible to remove all rust protection it can cause the paint to not attach properly. After having compared with similar articles a test were done to order a pair of bearing supports without corrosion inhibitor, which gave good results. This initiative also set in motion a process to do the same for more different items.For special pallet, a survey were made of the process with two different VSM and a calculation of how much ABB would earn at ordering more special pallets than getting the material delivered on the A-pallets.