When constructing a building, a number of aspects must be harmonized in order for it to fulfill requirements ? a building must fulfill requirements such a load-bearing, conservation of energy and a good indoor environment by means of, among other things, moisture proofing .Moisture problems in buildings can affect health negatively. As we are increasingly staying in indoors, demands on a good indoor environment are higher.This work starts with examining moisture problems in slab-on-ground solutions, and then links the various scenarios to moisture problems in a concrete slab of a real building. The building with moisture problems is located in Årby by in Borlänge and moisture damage was found in the slab at an apartment adjoining wall.By reviewing literature written within the field of moisture problem, making hand calculations and modeling in the program Comsol Multiphysics, judgments are made to find explanations as to why the rise of moisture occurred in the building in Årby by.Generally, the following guidelines may be used to reduce the risk of moisture problems in slab-on-ground constructions:Drying of construction moisture before laying the floor material.Using draining layer beneath the slab, to prevent capillary suction.Using insulation under the slab, partly for comfort and to establish the temperature difference between the ground and the concrete slab.Avoid direct contact between the wood and concrete, due to degradation and fouling smells that normally occurs.If necessary, use additional vapor barrier.In addition to the above, there are various methods for moisture-proof and moisture-monitoring by design or by the method ByggaF suited for the entire construction process various events..

This master thesis covers the seasonal planning of a small scale hydropower system. The system in this study is owned and operated by Mälarenergi Vattenkraft AB. The total system consists of 4 different main rivers with 24 hydropower stations and several dams. The total installed power in the system is 43.75 MW. Most of the hydropower stations are regarded as small scale hydropower stations and thus entitled to green certificates.In this report the issue of planning is formulated as an optimization problem.

Svensk Växtkraft is the owner of the biogas plant in Västerås. The company is planning to increase their treatment capacity at their biogas plant. In connection to this work it is also possible to make some energy saving changes to the biogas plant. The objective of this study was therefore to make an electricity and heat survey of the biogas plant, a detailed study of the heat consumption in the sanitation step and also a comparison of energy consumption with the present sanitation method and an alternative strategy where the waste is treated in 55 °C during 10 hours (the current method is heating to 70 °C during 1 hour). The energy survey was conducted in close collaboration with staff at the biogas plant. The current during normal operation was measured, power was calculated and multiplied by the time of usage to obtain the energy consumed.

This report will outline a proposal for the improvement of the baggage sorting facility at Arlanda airport. Swedavia is a state owned company group that operates, owns and develops airports in Sweden. One of their main roles is to create accessibility needed to facilitate and streamline the work at the airport.Swedavia is constantly working to develop new solutions and enhancements that will help to standardize and automate the work at airports without major impact on climate and above all adapt these solutions to work.The project has been aimed to identify and isolate the problem at the check-in counter, investigate the possibility of setting a speed control on the DC motor driving the luggage conveyer belt at the check-in desk so that the luggage does not lose tracking already there, as well as evaluate the new sorting systems planned to be introduce in the upcoming refurbishment of the sorting area.To determine the parameters that are used to regulate the speed of the baggage conveyor belt, information about the inputs and outputs that participated in the process was gathered. Information was collected both practically and theoretically. Process was followed and monitored by the supervisor of the company, and a theoretical study was done separately on my own.

The primary purpose of this paper is to find the determinants of first-day returns on the Stockholm Stock Exchange. Our research will cover the 1996 ? 2004 periods. Our secondary purpose is intended to find a profitable trading strategy with regard to future IPOs on the Stockholm Stock Exchange. By using regression analysis, focusing on company specific factors and the IPO process, we hope to find a function exhibiting statistical significance, determining future first-day returns from which construction of a profitable trading strategy will be possible.

ABB is one of the world?s leading engineering companies in power and automation technologiesand their solutions improve performance while lowering environmental impacts for energycompanies and industries. ABB FACTS designs equipment and plants for series and phasecompensation.This thesis has been performed at ABB FACTS on the Mechanical Design (DM) department inVästerås, Sweden. The purpose of the thesis was to develop and design calculations andsimulation tools for ABB FACTS?s standard series capacitor platforms.

The following report comprises my bachelor´s thesis in Industrial design, 30 hp. It is executed in collaboration with Bonum senior housing, who has been the client and assignment- maker of this project.The goal was to design a bench for their entrances, which could represent not only the needs of the target group but also Bonum as a trademark. The work is done with great care for both human kind and the environment, with sustainability as beacon.The design process has been followed.Initially, you will find the definition of a bench for entrances, the framework including inclusive as well as sustainable design, a function- and market analysis followed by the inspiration part of the project. Getting to know the target group and their specific needs has been essential for this work.Investigations about what senior house living and senior products are and what the target group thinks and feels, has been done. As a result, two ?personas? has been developed.With the help of a purposely chosen group of people, surveys and ergonomic studies has been executed, as well as prototype-testing.The fact-finding has formed the stable and unavoidable foundation of this project, which later on gets more creative and idea based.

This bachelor thesis project has been executed at Outotec Sweden AB in Skellefteå. Outotecs main business focus is selling mineral and metal processing technologies. A rest product from the metal process is particle-polluted gas and cyclone designs are today the most commonly used abatement device for particle control. A cyclone provides a simple design with high efficiency particle percolation by using air streams.The purpose of this work is to reduce the time it takes create new cyclone designs in Outotecs projects. An extensive construction work is needed for every new cyclone order due to new designs.

Chlorinated solvent are volatile organic substances that can be harmful for humans and for the environment. Examples of common chlorinated solvents are perchloroethene, PCE, and trichloroethene, TCE. Chlorinated solvents appear as contaminants in soils primarily where they have been used as washing fluids in dry-cleaning facilities or as degreasers in metal industries. Chlorinated solvents are DNAPLs (dense non-aqueous phase liquids), which means that they are not easily dissolved in water and that they sink to the bottom of the aquifer. Adsorption to soils is low so chlorinated solvents are mobile in soils.

It has become more common for organization to operate a lot of projects at the same time. These projects affect each other, either in way of resources or technical. Projects in a multi-project environment depend and affect each other, and in most cases they rival about resources, decision-makings and priority. To lead a project portfolio with several projects is a major challenge. The most common problems that occur are vague objective, unclear working conditions, resource shortage and problems of priority.

This thesis work has been performed at the department of diagnosis and dependability at Volvo Car Company, Torslanda. The background of this project is based on interest in ascertaining how different factors possibly can affect a diagnosis method, which has been developed to find leaks in the fuel tank and evaporation system. According to the OBD II requirements leaks with an orifice diameter larger or equal to 0,5 mm, must be detected. The idea of the diagnosis method is to create an over pressure in the system with an air-pump. The current through the pump is measured and correlates to the power consumed by the pump.

This thesis is based upon the work done at Westinghouse electric company (WEC)inVästerås during the spring semester of 2015 and describes the development of a quickcoupler with associated blade changing tool. These are meant to be used togetherwith a sawing tool that the company uses for the dismantling of nuclear reactors,which is performed under water.The aim of the thesis was to develop a complete manufacturing documentation withdrawings and related CAD models which Westinghouse later can use to manufacturethe tool and the quick coupler. It was also included in the assignment to, if necessary,modify parts of the saw tool to adapt these to the intended blade changing tool.A number of visits to the company's workshop was made during the time to study thesaw that the thesis is based upon. The purpose of these visits was to get a better ideaof the dimensions, construction and the field of use of the saw. On three of thoseoccasions various engineers and consultants accompanied us to discuss possibleproblems with different ideas.This was interspersed with information in the form of literature studies on quickcouplers to create a clearer picture of the nature of the task.When enough information had been gathered a functional analysis was made to dividethe main problem into subthis phase the idea and concept generating process took place.The methods used for this was mainly brain writing and brainstorming.

This is a thesis project in the field of information technology which begins by evaluating existing food price comparison systems and subsequently aims to design an improved, web based system for said purpose. The system features interfaces for price reporting, price comparisons as well as various search and review functions. The objective is to create a system able to compete with existing price comparison systems, which requires careful selection of products that can be found in all foodstores that also represent different households; a user-friendly price reporting and price comparison interface and an efficient tool for ensuring the validity of reported prices.The designed system features a more accurate formula for calculating average prices in events where the real price is missing; a more reliable security mechanism forv alidation of reported prices and a more comprehensible interface for viewing price reports, reporting prices, reviewing stores and products in comparison with existing systems. The system does, however, suffer from some optimization issues primarily in the form of inefficient database modeling; SQL queries and JavaScript code although testing has shown that these shortcomings do not hamper overall performance to such a degree that usability is compromised. Further usability testing performed on the system with five test subjects shows that a high level of overall user-friendliness has been achieved even though some special features, such as the detailed report containing price information per product for each store need to be improved.It is not possible to say at this time whether or not the designed system will be able to compete with existing ones or if the very concept of food price comparisons per se is viable in terms of profitability and marketability.

The discharge from Lake Mälaren is regulated to keep the lake water level within limits set by a water decree. Despite this, in the year 2000 the lake water level rose above the upper limit. Studies conducted at the climate modeling unit Rossby Centre at the Swedish Meteorological and Hydrological Institute (SMHI) indicate that the inflow to the lake may increase in the future. A flood in the area will, among other things, strike infrastructure and residential districts.The aim of this study was to investigate the water levels of Lake Mälaren in future climates. In addition to this possible future expansion of the lake discharge though the sluice gates in order to keep water levels below limits set by the water decree and to prevent flooding of the shoreline were discussed.

The  construction  industry  is  a  costly  business  such  in  respect  of  capital  for  most construction defects which then require rework, tear down and rebuild again. This study is  meaningful  awareness  of  tools  that  can  reduce  this  best  through  communication  and information sharing between the parties.  The  construction  industry  is  known  as  temporary  projects  organizations,  where  the construction  project  consists  of  several  actors  who  have  to  communicate  and  share information  between  them  to  avoid  mistakes  later  in  the  build  time.  These  actors  are bounded together thus for the duration of the project, then broken when the project has reached its end. The challenge here is for these actors to apply a tool that can help and simplify communications, information sharing, and perhaps the most important aspect is to  create  a  routine  for  the  association  and  the  shattering  of  these  actors.  To  implement such  behavior  using  a  tool  such  as  BIM  in  the  industry  whose  size  perhaps  is indescribable may be a very hard task.  BIM (Building Information Model) could be seen as the solution to this problem because it  acts  as  a  portal  where  the  actors  involved  must  sign  in  and  communicate,  share information, and eventually create a behavior, a routine for this association and division of  the  actors  following  the  end  of  the  project.  The  technology  could  help  the  involved from  the  beginning  of  the  project,  already  in  the  model  stage,  break  down  and  prevent any construction barriers when the building has been placed in the works.