Floor surface in pig facilities can have an impact on animal welfare and pig health, as it can cause the pig physical damage and thereby increased risk of infectious diseases and lameness. The development of pig housing systems has resulted in a decreased use of bedding. It seems hard to find the optimal floor in farrowing pens, as it must suit both the sow and piglets. The floor friction needs to be adequate to avoid slips and at the same time should the floor be non-abrasive. Abrasions and lesions caused by the floor are not only causing the animal suffering, but are also negative from an economical aspect.

The incidence of damage to the claws and legs in piglets caused by the floor in farrowing pens is a widely known problem and very common in today's pig herds. Although the association between floor and damage has been known for over 35 years, no suitable solution has been found to reduce the negative impact. The purpose of this study was to make a literature study to document the experiences of the use of different types of flooring in farrowing pens and also, in an own study, examine if soft floor in farrowing crates could lead to reduced damage to the claws and legs in piglets compared to concrete floor. The study was conducted in two herds, A and B. In each herd, farrowing pens with concrete floor and concrete floor with Polyurethane coating were compared.

This report compares two different types of insulation with regards to fire and moisture. The materials were tested for the company Fiskarhedenvillan AB, for a wall and a roof construction that the company currently uses in the establishment of Sweden's first certified passive house for international standards.Their current material, Rockwool, is compared to a relatively new material on the Swedish market called SEALECTION Agribalance sold by the company ISO Green AB. The material is a type of Polyurethane insulation. This insulation material would result in a more efficient execution of the construction as it provides waterproofing and is applied more easily than Rockwool. From a fire standpoint, literature studies and discussions with fire experts led to results.

Uppsats för avläggande av filosofie kandidatexamen iKulturvård, Konservatorprogrammet15 hpInstitutionen för kulturvårdGöteborgs universitet2014:03.

En vanligt förekommande laminering är polyuretanskum, som används för att ge egenskaper som mjukhet, komfort och flexibilitet till textiler. Ett användningsområde som tillverkaren och leverantören Borgstena Group Sweden AB använder polyuretan till är lastbilars väggpaneler. De vill dock ersätta den polyuretanskumlaminerade dubbeljerseytrikån som används idag med endast en ren trikåkonstruktion för att slippa problem som dellaminering och minskade töjegenskaper. Dessutom så har den kemiska sammansättningen av polyuretan som används i lamineringen visat sig vara belastande för både miljö och människor. I denna rapport klargörs varför polyuretanskum behöver ersättas och vilka möjligheter som finns i dagsläget för att göra detta.

As reptiles are becoming more common as patients in veterinary clinics, there is a need for creating new procedures regarding the care of exotic pets. The aim of this study was to develop a wound care routine adapted to reptiles, which can be used independently by a veterinary nurse due to the absence of prescription drugs or surgical techniques. The study was conducted by compiling the available research regarding wound care in reptiles, as well as research from related fields. The result indicates that Polyurethane films and chlorhexidine-alcohol may advantageously be used on these patients. Hydrocolloid dressings and silver sulfadiazine dressings have adverse effects on wound healing and should not be used routinely in reptiles.

This thesis engages the topic of test methods for wood adhesives. Two test methods were evaluated, EN 302-1, a European standard, and ASTM D905, an American standard. The total amount of specimens manufactured and tested was more than 500. The adhesive bonds were tested in shear with an increasing load on the specimen until failure.The adhesives used were epoxy-resin, phenol-resorcinol-formaldehyde and a 2-K Polyurethane. The test programme included five different types of intentional errors per method, in order to investigate the sensitivity of the test methods.

With a growing population on earth the amount of end-of-life vehicles (ELVs) and other scrap steel increases. The European Directive 2000/53/CE? requires a minimum of 95 % reuse and recovery and 85 % re-use and recycling no later than 1 January 2015, for end-of life vehicles. This imposes a need for more efficient recycling and recovery. Despite this shredder residue (SR) is commonly land filled.This report investigated the magnetic fines residue generated at Stena Metall shredder facility in Halmstad, Sweden.

With a growing population on earth the amount of end-of-life vehicles (ELVs) and other scrap steel increases. The European Directive 2000/53/CE? requires a minimum of 95 % reuse and recovery and 85 % re-use and recycling no later than 1 January 2015, for end-of life vehicles. This imposes a need for more efficient recycling and recovery. Despite this shredder residue (SR) is commonly land filled.This report investigated the magnetic fines residue generated at Stena Metall shredder facility in Halmstad, Sweden.

By our employer Camatec Industriteknik AB have we been given the assignment to continue with the previous work ?Design of strip feeder?. Our goal with this work is to come up with a design basis for a strip feeder.Functionally a strip feeder consists of two rollers which with the aid of the friction between the strip and the coating on the roller create a strip force that pulls the strip through the working progress.Demands on this project:? 10 ? 600 mm in strip width and 0,1-1 mm in strip thickness.? Minimum 30m/min in production speed.? A maximum strip force on 30-40 kN.? The cost of the strip feeder?s components is to be considered of economy and quality.The need of a strip feeder occurs when the coil doesn?t manage to feed or pull the strip before or after a working process. The strip can otherwise be exposed by a permanent yield deformation or a change in the strip material if it?s pulled trough the working process only by the on ? and of-coils.

This study aimed to evaluate the levels of formaldehyde and organic acids that can build up within enclosed spaces. Another goal was to compare two types of paints that can be used as coating barriers within showcases and in turn compare them to the modern, and by many highly recommended, material of Marveseal®. A low volatile waterborne alkyd/acrylate paint and a two component Polyurethane paint was compared to Marveseal® in two series of experiments. One series measured the level of formaldehyde, and thus the effectiveness of the three chosen barriers, and the other series measured the level of volatile organic acids, both the acids emitted from the paint itself, and that of the wood. One box in each series were not treated at all and was used as a reference.The fact that different types of materials emit volatile organic compounds have long been known.

This thesis is about developing a design that provides improved vacuum seal between a lead coating and a plastic coating during plastic extrusion processes of cables. This report is a part of the course MSGC 17 for Bachelor Engineers in mechanical engineering.The work is performed at Nexans Norway AS in Halden where they have a production of high voltage cables for sea-, and offshore industry. A problem they face is that they do not get enough good seal at the attachment to the plastic extrusion machine. They want to achieve a vacuum between a lead coating on the cable and a plastic coating of the cable for plastic extrusion, which is something they do not achieve today. The thesis is thus to come up with a design that provides better sealing against the cable.The work involves a construction part with the phases of product development processes.

En funktionsbeläggning består av ett polymert material som beläggs till en textil yta. Denna typ av beläggning används för funktionsplagg och det belagda materialet har som uppgift att skydda användaren från vatten samtidigt som den har god ånggenomsläpplighet. För att tvärbinda funktionsbeläggningen och öka dess hållfasthet appliceras ett översta skikt av polymer som kallas topcoat. En topcoat innehåller tvärbindande ämnen som till exempel isocyanater eller formaldehyd. Dessa ämnen är mycket miljö- och hälsoskadliga.