This thesis aims to develop a control system for measuring electromagnetic compability (EMC). This has meant that a controller designed around an ATmega8 Microcontroller has been manufactured and programmed. It has also meant the development of a comprehensive control software in the program MATLAB. The control system has been tested with satisfactory results and can now, monitor and control measurements of the EMC-type..

This thesis has been carried out in collaboration with LEDtec International AB. LEDtec focuses on innovative solutions in LED screens. Everything from large advertising signs to welcome signs in cities, to screens indicating speeds or warning of heavy traffic. The task was to was to help them develop a new version of the control board that is used in some of their products. The reason for this is that their old control board is obsolete and the components that are on it, is no longer manufactured or in need to be renewed.

 Autonomous cars or robot cars havebeen on the agenda ever sinceHollywood started with their Sci-Figenre, maybe even before that. A lotof things have happened since then andnow the self-driving vehicle is notfar away. In this project, theAutonomous car with Microcontrollerand ultrasonic sensors, we are lookingat a way of making a small, regular RCcar autonomous with relatively simplemeans and investigate how the bigcompanies does it to learn more aboutthe development of the autonomous carsand their technology.We used an Arduino Uno R3 supplementedwith an Arduino Motor Shield R3 as ourMicrocontroller board and three HCSR04ultrasonic sensors. By removingalmost all of the old parts of the RCcar,except the two DC motors, andreplacing them with these new parts wemanaged to make a vehicle that drovearound in a room without crashing intoanything. We could have used entirelydifferent sensors, or supplemented theexisting setup with other sensors tomake it even more accurate andobstacle avoiding.

Construction of an autonomous wind station was a project with the goal of creating a product that could collect wind data from a sensor and then transfer this data to a server wirelessly over the GSM network. The device would be powered by batteries and solar cells and function fully without requiring external power supply. This required that a small computer was constructed and programmed to store and send data at predetermined cycle times and programming of a server that received the sent data. The project also required optimization of power consumption and dimensioning of solar cells and batteries based on this. The construction of this station demanded research both for the selection of hardware and programming software. The computer was based on a Microcontroller and a GSM module that sent the data over the 2G network.

This thesis for the Master of Science degree was performed at Oppunda Electronics AB. The assignment was to further develop an existing prototype of a dispensing equipment. The dispensing equipment doses a kind of glue, bonding which dentist use to mend teeth. The dispensing equipment is adjusted to dose 12 micro litres of bonding. With the dispensing equipment SafeBond Electronic the user can reduce the bonding consumption with approximately 50 percent.

This report describes the design and implementation of a multi-master, packet based protocol for small and tiny Microcontrollers where resources are limited. The protocol was named "Tiny Controller Network" or TCN for short. The protocol is meant mainly as a control bus for automation and sensor acquisition applications but due to its flexibility can also be used for other purposes as well. It borrows some of its functionality and design ideas from the well known CAN bus and Modbus but also has a number of major differences like the use of standard hardware and time synchronisation. One of the key aspects during the design was the use of very little system resources and common on-chip hardware peripherals like a UART.

This report presents a master thesis project performed at Elekta AB during the fall of 2013 and early 2014. Elekta is a medical technology company and their main product in the Stockholm office is a gamma knife used for radiosurgery. The gamma knife contains a cluster of a dozen motor servos and motors used for adjusting the patient and the radiation sources over a CAN bus. A self-developed hardware-in-loop simulator running on a PC with LabVIEW is currently being used for integration level testing of the control system of the gamma knife. The simulator has some problems with it not running in real-time and having other performance issues.

This report presents a master thesis project performed at Elekta AB during the fall of 2013 and early 2014. Elekta is a medical technology company and their main product in the Stockholm office is a gamma knife used for radiosurgery. The gamma knife contains a cluster of a dozen motor servos and motors used for adjusting the patient and the radiation sources over a CAN bus. A self-developed hardware-in-loop simulator running on a PC with LabVIEW is currently being used for integration level testing of the control system of the gamma knife. The simulator has some problems with it not running in real-time and having other performance issues.

People are usually directed towards each other in conversations, to make it easier to hear what is being said. Algorithms for voice and speech recognition works in a similar way, regarding the microphone direction towards the sound source. In this thesis in electronics has therefore a servo control with binaural sound localization been implemented on a Microcontroller connected to two microphones.When people perceive sound, the brain can estimate the sound source direction by comparing the time taken by the sound reaching one ear to the other [1]. The difference in time is called the interaural time difference, and can be calculated using various techniques. An exploratory comparison between the techniques cross-correlation and cross-spectrum analysis was carried out before implementation.

This report describes the design and implementation of a multi-master, packet based protocol for small and tiny Microcontrollers where resources are limited. The protocol was named "Tiny Controller Network" or TCN for short. The protocol is meant mainly as a control bus for automation and sensor acquisition applications but due to its flexibility can also be used for other purposes as well. It borrows some of its functionality and design ideas from the well known CAN bus and Modbus but also has a number of major differences like the use of standard hardware and time synchronisation. One of the key aspects during the design was the use of very little system resources and common on-chip hardware peripherals like a UART.

The combustion engines in today?s vehicles are getting more and more advanced and there are increasing demands on that the engines should operate during optimal conditions. Examples of internal combustion engine parameters which may be carefully controlled are the rate between fuel and air, that this gas mixture is homogenous enough and that it is ignited at the correct moment. Moreover, the requirements of these parameters vary depending on, among other, engine speed and load. To meet these requirements in all occurring operation conditions, it is required that many subsystems work together.

A LED spectrometer has been constructed for qualitative spectrometry using certain wavelenghts. The LEDs and the photodiode are being controlled with a Microcontroller that is connected to a computer to power the components and save data. The spectroanalysis made with the LED spectrometer were significantly different to a standard spectrometer, concluding that more analysis should be made until a final product is ready. Some areas of improvements are suggested. .

This thesis aims to develop a control system for measuring electromagnetic compability (EMC). This has meant that a controller designed around an ATmega8 Microcontroller has been manufactured and programmed. It has also meant the development of a comprehensive control software in the program MATLAB. The control system has been tested with satisfactory results and can now, monitor and control measurements of the EMC-type..

In this bachelor thesis a complete prototype of an industrial vibration measurement platform has been developed. By measuring a number of variables such as acceleration, temperature and speed conclusions can be drawn on machinery health. The aim is to evaluate hardware and software solutions for a possible future product. Based on a requirement specification a proper hardware design has be developed. The hardware consists of a four-layer PCB with an ARM Cortex-M3 Microcontroller and about 250 other components. The PCB was designed, assembled, tested and finally housed in a box.

A study was carried in conjunction with the Orthodontic department at Halmstad General Hospital in Sweden to investigate the possibility of reducing cost and manufacture time of dental implant drill guides. The current system involves sending a digital image in STL format to the Materialise factory in Belgium where information of the position of dental implants is translated onto a moulded mouthpiece. Drill guides are placed in the mouth piece which is then returned to the surgeon. The mouthpiece complete with drill guides is then placed in the patients mouth and used as a guide for the implant drill holes. The cost of 10000 sek and a turnaround time of 2 weeks gave rise to the need for a faster and cheaper solution.