This report present the design and manufacturing of a wide-band driver Amplifier placed in radar module for airborne applications. The major goals for the Amplifier were a high efficiency and to deliver a predefined output power. To reach the second goal an additional preAmplifier had to be constructed. The Amplifiers were constructed in three steps: Design and Layout in the software Microwave Office, Mounting components and Verification. The driver Amplifier was decided to be a push pull configuration consisting of two parallel transistors biased in class AB.

Softube has developed DSP-card and software for simulation of the sound of old tube Amplifiers. The purpose with this thesis is to design a compact Amplifier with high power to function together with the DSP-card and build a unit that can replace several other guitar Amplifiers. The advantages with that kind of solution could be that it would be cheaper, easier to carry and easier to stor than the real Amplifiers. The Amplifier that has been designed is of class D type with digital PWM modulator. There is several types of Amplifier modules on the market that use analog input signal, but if one of them would be used a D-A converter is needed on the DSP card.

The purpose with the report is to show that it is possible to design a class-D Amplifier, using a programmable FPGA mounted on a developing card from Xess and a H-bridge. The FPGA was programmed in VHDL which is the language the software from Xilinx use to implement a logical function into the FPGA The logical function corresponds to a modeling of the music signal and the modeling can be described as a comparator which compare the music signal with a triangle wave and as a out signal produce a pulse width modulated (PWM) signal. The report is also a review and evaluating of two different modulating technologies, AD- modeling and BD-modeling. A detailed part about how the H-bridge was designed and how it works. The result of this project is a working audio Amplifier to a significant lower price than the products in todays market..

This report is an outcome of a master degree project at Linköpings University in co-operation with Micronic Laser Systems AB. The purpose with this master degree project was to investigate how to implement a receiver in a data transfer system. The system consists of several data channels, where every channel consists of three parts: driver, transmission lines and receiver. The driver send low amplitude differential signals via the transmission lines to the receiver that amplifies and converts it to a single-ended signal. The receiver has to be fast and be able to feed an output signal with high voltage swing.

The last few decades the development in the field of electronics has been huge. The components performance gets better at the same time as the manufacturing cost decreases. Many of the design moments that have to be done, are done automatically today, but it can get better. Especially for analog circuit design.At Electronic System in Linköpings universitet, research is in progress to develop a tool that can design analog circuits in reasonable time. It means that it has to size the components (transistors, resistances, capacitances etc), so that the circuit can fulfill the performance requirements.

This paper describes a method for wireless energy transfer via near-field electromagnetic inductionthat is inexpensive, simple and can be applied to almost any type of system, regardless of size andenergy demands.The method uses a primary unit consisting of an oscillator, Amplifier and inductive coil thattransfers energy to a secondary unit consisting of a coil, rectifier and voltage regulator. Two typesof oscillators and several Amplifier designs were realized and evaluated together with a multitudeof flat coils of both monofilar and bifilar type.The results show that it is important to use an oscillator whose frequency is dependent on theinductance of the connected transmission coil, such as the Colpitts oscillator. This is preferable toan oscillator with a preset frequency, such as a Schmitt-trigger oscillator..

This paper describes a method for wireless energy transfer via near-field electromagnetic inductionthat is inexpensive, simple and can be applied to almost any type of system, regardless of size andenergy demands.The method uses a primary unit consisting of an oscillator, Amplifier and inductive coil thattransfers energy to a secondary unit consisting of a coil, rectifier and voltage regulator. Two typesof oscillators and several Amplifier designs were realized and evaluated together with a multitudeof flat coils of both monofilar and bifilar type.The results show that it is important to use an oscillator whose frequency is dependent on theinductance of the connected transmission coil, such as the Colpitts oscillator. This is preferable toan oscillator with a preset frequency, such as a Schmitt-trigger oscillator..

A current conveyor is an active building block that can be used to implement most active and passive components. It differs from the operation Amplifier in that it uses current instead of voltage. The current conveyor also has significantly higher voltage gain over a broader frequency range. To simplify the construction of analogue circuits and increase the construction efficiency it is desirable to use a top-down methodology. This means that the whole system is partitioned into a hierarchy of subsystems.

In this Master's thesis, a direct-conversion receiver front-end has been designed in a 0.18um CMOS technology. Direct-conversion receivers (DCR) have obvious advantages over the heterodyne counterpart. Since the intermediate frequency (IF) is zero, the problem of image is circumvented. As a result, no front-end image reject filter is required and the channel selection requires only a low-pass filter, which makes it easy to integrate directly on chip. However, the DCR also suffers from several drawbacks such as extreme sensitivity to DC offsets, 1/f noise, local oscillator (LO) leakage/radiation, front-end nonlinearity and I/Q mismatch.

In this report we describe an adaptive simulated annealing method for sizing the devices in analog circuits. The motivation for use an adaptive simulated annealing method for analog circuit design are to increase the efficiency of the design circuit. To demonstrate the functionality and the performance of the approach, an operational transconductance Amplifier is simulated. The circuit is modeled with symbolic equations that are derived automatically by a simulator..

Att ansluta en digital signalprocessor kräver ett omfattande arbete. Innehållet i denna rapport sammanfattar teoretiska metoder för att integrera den digitala signalprocessorn ADAU1701 i talförstärkaren MMT-4, utvecklad av företaget Xena Medical. Arbetet har till största delen bestått i att finna en lämplig DSP och studera dess datamanual för att anpassa den till talförstärkaren.Mycket av rapporten sammanfattar beräkningar av komponentvärden och anpassning av ADAU1701 för MMT-4:s behov. ADAU1701 beskrivs utifrån det så kallade selfboot-läget där processorn kan arbeta som fristående processor..

Normally the operational Amplifier is used as a component in active filter design. The goal for future components in filter design is large bandwith and the use of low supply voltages. The use of current-mode instead of voltage-mode circuits gets a step closer to the required performance. A component that use current as the signal conveying part is the current conveyor. In this report a comparative study between two current conveyor structures of second generation (CCII) is performed.

Embedded Systems Lab at Umeå University is currently part of a research project with the purpose to examine the behavior of dairy cows inside a barn. Each cow needs to be tracked with a precision of 50 cm, and since GPS-technique has poor functionality at indoor environments, an indoor positioning system needs to be developed.Embedded Systems Lab has already developed an indoor positioning system using IR-light and radio, but since this system demands extensive infrastructure and is rather expensive, an alternate positioning system using ultrasonic pulses and radio is being examined.In this report the range, beam angle and current consumption of ultrasonic transmitters- and receivers are investigated. Three different driver stages for the transmitter is tested, and two Amplifier solutions for the receiver. The report also describes how the length of the transmitted ultrasonic pulse affects the received signal, accessibility of a ?shadowed? signal, and the effect of different sound frequency..

This project started when LIC Audio AB wanted help with development of a hearing aid for public rooms. The problem is that a lot of people suffer from some sort of hearing impairment. In places with a lot of people and background noise the problem becomes bigger and the sound seems to flow together. During the project we found the solution for the problem in the shape of a headphone. The headphone receives a signal from a preinstalled hearing loop.

Development and construction of an electronic Breakout box is the main work for this thesis. The box is a part of a test system for the component Fuel Flow Transmitter and should convert signals to be suitable for a frequency counter. A previously constructed Breakoutbox for this purpose is being old and needed to be recreated. So SAAB Aerotech, Aircraft services, the company for the thesis work wanted to construct a new, more sustainable Breakoutbox adapted to a more modern technology. The signals to the box comes from the transmitter and should be converted to suitable signals for a frequency counter so it can show pulse and time difference between the signals.