In this thesis an energy analysis of ethanol production at the ethanol plant of Lantmännen Agroetanol in Norrköping has been performed. The ethanol plant has been studied in combination with Händelöverket, the combined heat and power plant which provides the ethanol process with steam. The purpose of this study was to determine the energy consumption for the whole production chain from grain to ethanol. The analysis has included the energy consumption for cultivation of grain, production of chemicals, the production chain for wood chips, the steam production and the ethanol plant. The grain and wood chips are both considered raw materials there for the energy content in these are not included as energy input in the system.

AbstractDelta Terminal owns an outdated industrial building which they now rent out to businesses. This property currently has a high energy con-sumption and therfore it is desirable to improve the efficiency. In ordet to reduce the energy consumption within the industrial building enve-lope, the heating systems and lighting are being investegated. A good building envelope emits less heat and thus reduces the energy consump-tion. An energy audit is a tool used to determine the energy loss.

With the climate change issues growing in importance on the social agenda, the field of urban masterplanning is of no exception when it comes to minimizing the carbon footprint in a variety of projects. The aim of this thesis has been to prepare the Carbon Critical Masterplanning tool, a software plugin for carbon dioxide emissions assessment developed by Atkins, to be used in Swedish conditions. The main targets were to improve the areas of the tool associated with energy conversion and renewable energy sources, and to test the tool in a real case. A planned construction of a new campus in Albano, Stockholm was chosen for the pilot study. A 3D model was built in the tool and the carbon footprint was calculated for a variety of combinations for energy supply to the future area. The results show that use of locally installed renewable energy sources can reduce the total climate impact when life cycle perspective is applied.

Värmeböljorna blir allt vanligare i Sverige vilket kommer kosta sjukvården miljardbelopp. Hur kan denna trend motverkas? Träd kanske inte är hela lösningen på problemet, men är en hjälp på vägen. Det urbana landskapet har idag högre temperatur än omgivande landsbygd. Detta fenomen, den så kallade urbana värmeö-effekten, beror bland annat på att hårdgjorda ytor absorberar solenergi, antropogena källor utsöndrar värme, luftföroreningar fungerar som växthusgaser och bristen av nerkylande vegetation. Dessa faktorer bidrar till en ohållbar temperaturstigning. Kandidatarbetets mål har varit att ta reda på hur träd bidrar till en temperatursänkning inne i städerna och att identifiera urvalskriterier för att välja träd ur temperatursynpunkt som samtidigt fungerar i urbana miljöer.

With the climate change issues growing in importance on the social agenda, the field of urban masterplanning is of no exception when it comes to minimizing the carbon footprint in a variety of projects. The aim of this thesis has been to prepare the Carbon Critical Masterplanning tool, a software plugin for carbon dioxide emissions assessment developed by Atkins, to be used in Swedish conditions. The main targets were to improve the areas of the tool associated with energy conversion and renewable energy sources, and to test the tool in a real case. A planned construction of a new campus in Albano, Stockholm was chosen for the pilot study. A 3D model was built in the tool and the carbon footprint was calculated for a variety of combinations for energy supply to the future area.

I detta examensarbete har termiska förhållanden undersökts för modulen eSite som är under utveckling av företaget Flexenclosure. eSite omvandlar och riktar ström från en mängd olika producenter och skickar denna vidare till förbrukare. Kylning av komponenter tänkta att sitta inuti eSite har simulerats och analyserats. Komponenterna är placerade på en värmesänka, över vilken naturlig konvektion uppkommer. Denna företeelse har undersökts med hjälp av både manuella beräkningar och datorstödda flödessimuleringsberäkningar (CFD) i mjukvaran Ansys® 14.5 och beräkningsverktyget Fluent?.

The company Olofsfors AB manufactures drive belts for forest machinery, known as ECO-Tracks, and abrasion-resistant steel and cutting edges for graders, excavators and tractors, known as Bruxite and SharqEdges. Manufacturing these products requires the steel to be heated and molded, then submerged in water and hardened. The water used in the hardening of steel is pumped to the process from pits below the floor and then pumped back to the pit after it?s been used. Since the temperature of this water rises after being used to harden the steel the temperature of the pumping pit needs to be adjusted to maintain its setpoint of 21°C.

Högbytorp is Ragn-Sells? largest waste facility and it is located north of Stockholm. There is an old landfill still in use, but at the end of this year it will be closed. The waste deposited on the landfill can, through decomposition, give rise to a large amount of methane gas, which is an energy rich gas that can be used for heat and electricity production. To receive a relatively large amount of gas, the decomposition requires a high moisture content in the waste.

AbstractIII-essay in political science by Christoffer Harnell, autumn -08. Supervisor: Malin Stegman-McCallion. ?Nuclear Disarmament - USA and the Soviet Union 1960-2002? This essay is about USA and the former Soviet Union and their nuclear disarmament. The purpose is to explain why and when the two states begun their nuclear disarmament, as well as what caused the start of the process.

The aim of this study was to evaluate the stir drying method, for drying of grain during Swedish conditions. The evaluation was done during the harvest year 2004, on four farms with stir driers. The driers were evaluated for their energy consumption, design, stirring effectiveness and how much time the farmer has to spend on every tonne of grain. A comparison was also done with conventional Swedish high temperature driers. Totaly six batches of grain from stir driers were examined, mostly winter wheat, but also barley and wheat.

Emission of nitrogen oxides as well as carbon monoxides is an inevitable result of combustion. A Swedish law "Law of environmental fee for emissions of nitrogen oxides as a result of energy production" (lagen om miljöavgift på utsläpp av kväveoxider vid energiproduktion (SFS 1990:613)) controls the emission of NOx from energy production by a system of fees. The system has resulted in a strong approach toward less emissions of NOx among the energy production plants. High emission levels, today exceeding 52 mg/MJsupplied fuel, leads to costs for energy production companies. This paper examines possibilities to reduce the emissions of NOx by optimization of the SNCR-technique in a biofuel fired heat and power plant.

In the EU the amount of waste increased by 14 percent during the years 2000 to 2010. EU?s target to reduce waste generation runs parallel with the aim of increasing the efficiency and profitability aligned with energy recovery. In Sweden the energy recovery through incineration is increasing steadily, and 46 percent of the municipal solid waste (MSW) is treated by combustion. This report aims to examine the profitability of processing MSW into Refuse Derived Fuel (RDF) from an economic-, energy- and environmental perspective.

The aim of this essay was to study the nitrogen flow in two willowplantations, at different locations in the south of Sweden, that wereirrigated with sewage. The study was also performed to compare thedifferences in nitrogen flows between two years, 1998 and 1999. The studywas made in three parts. First, the denitrification activity was measuredusing the acetylen inhibition method. Second the nitrogen flow, as well asthe water- and heat flows, were modeled through the SOIL-SOILN-modelThird; the nitrogen flow was calculated to compare with the results fromthe model.The results from the measurements were then compared with the resultsfrom the SOILN-simulations to detect differences in the denitrificationrate.

The company Olofsfors AB manufactures drive belts for forest machinery, known as ECO-Tracks, and abrasion-resistant steel and cutting edges for graders, excavators and tractors, known as Bruxite and SharqEdges. Manufacturing these products requires the steel to be heated and molded, then submerged in water and hardened. The water used in the hardening of steel is pumped to the process from pits below the floor and then pumped back to the pit after it?s been used. Since the temperature of this water rises after being used to harden the steel the temperature of the pumping pit needs to be adjusted to maintain its setpoint of 21°C.

The background for this degree thesis is a need to replace the existing seal used to protect equipment containing secret or sensitive equipment used by Swedish Defence. The target design should satisfy both the need for tamper evidence and reduce Life Cycle Cost. In developing a new design for a seal, additional benefits such as improved logistics support and indication of attack methods such as heat and solvents have been considered.The lack of guiding principles for end users of seals became evident during the interviews. Major concerns for the future are education of users, information about actions if a seal is broken and user liability.The design work was divided into several phases. A feasibility study was performed including investigation of theory of labels, materials and possible technologies.