With the elevated oil prices of today it is necessary to look for other heating alternatives. If the oil price continues to develop in the same way it has done the last years it will soon be impossible for many producing garden companies to survive. The purpose of this diploma work is to compare three different fuel options in order to find the most economic one considering the conditions of Katrinebergs Handelsträdgård AB. In relation to oil it is profitable to change to any of the three alternatives: wood chips, wood pellets and grain. The most profitable option is to change to wood chips. This alternative has a payoff time less than three years and after that the annual saving compared to the oil is relatively high. The annual cost is 65 % of the cost of the oil alternative.

The Swedish production of biogas was 1,5 TWh 2011. About half of the production was used as vehicle fuels. The cost for upgrading biogas depends on the size of the biogas plant and its gas production. If the gas flow is low the cost will be high. However, further development of existing upgrading technologies or development of new ones, have good potential to decrease the upgrading cost for small scale biogas plants.

This thesis analyses the prerequisites, profitability and competitiveness of eucalyptus plantation on the Iberian Peninsula and in Brazil. The thesis has a macro perspective and analyses a typical hectare of eucalyptus in each studied region. A survey methodology was used as a strategy to cover a broad perspective using expert respondents. The regions studied on the Iberian Peninsula were the ones found suitable for eucalyptus plantations from an economic point of view. The studied regions were Huelva in the South West of Spain, Galicia in the North West of Spain and Portugal.

This paper deals with the opportunities for the technique of condensation, for wood fired household heaters, on the Swedish market. In this project the condenser is preceded by a scrubber and both energy exchange and separation of unburnt particles have been studied. The facility studied is connected to a wood stove at 30 kW. The tests would show that the effect from the stove never reached above 16 kW. This might be a result of the low temperature of the water going into the stove, from the condenser. In addition to this the wood was not of highest quality and the stove could have needed some maintenance before the tests.

Tomo Hugglink (TOMO Skog) is an innovation for harvest and transport of biofuels. The system consists of a truck, a chipping unit and crane mounted on a link and a wood chip trailer. The system works in such a way that the chipping unit is disconnected and placed on the site and wood chips are loaded directly into the wood chip trailer.The aim of this study was:- To examine the performance of the TOMO Hugglink system under different conditions such as the size, placement and quality of the pile.- To calculate the cost per raw ton for two vehicle combinations at different transport distances and to examine the effect of a reduction in set-up time and an increase in load weight.- To identify possible improvements with the TOMO Hugglink system.A time study was conducted within the thesis work to make it possible to determine production and time consumption. In the subsequent economic analysis the cost per tone at different transport distances was calculated for two different lorry concepts. Furthermore the effect of a reduction in set-up time and an increase in load weight was calculated.Under current conditions the utilization of the chipper is low and only 29 % of the total system time is occupied by chipping.

Stump wood is a hot alternative when the heating plants demands more and more forest fuel. The aim with the study has bean to calculate the costs in four different systems for transportations of stump wood, examine if there are any differences in fuel quality for the stump wood in the different systems, analyse if the fuel quality in stump wood is affected with the time it lays by the road side and how much space the stump wood demands on the road side. To calculate the costs for the different systems a system analysis was carried out, where some of the costs were collected through field studies on Holmen Skog stump experiment and other costs were collected from literature and contacts. Data for the fuel quality study was collected from Eons heat plant in Norrköping. Data for the study of how much space stump wood takes along a roadside was collected from field studies.

This report is a bachelor's thesis of two students from the Energy and Environment degree at KTH Stockholm. Grinda is an island situated Stockholm archipelago. Skärgårdsstiftelsen is landowners and manages the area. Grinda Wärdshus, a guest house located in the island, currently uses an oil-fired boiler as a heating system. The aim of this thesis is to investigate whether wood chips or pellets is, from a sustainability standpoint, a suitable heating method for the guest house.

This final thesis is initiated by the wood fuel department at the Swedish forest company Sveaskog as part of a project which also involves two other final thesises. The overall goal of the project is to investigate Sveaskog´s possibilities to produce and sell different wood fuel assortments in Västerbotten and the southern parts of Norrland. The aim of this thesis is to investigate how much wood fuel Sveaskog can produce in the area during the next five years and what that would cost. Furthermore the thesis will investigate the total possible supply of wood fuel from all other possible producers in the area. Treated assortments are forest residues from final fellings, whole trees from direct wood fuel thinnings, non industrial wood and industrial by-products from sawmills. The main effort to investigate Sveaskog´s production possibilities has been made to calculate the possible annual amount of forest residues and fuel from wood fuel thinnings that can be produced.

The competition for Norway spruce pulp wood in Central Sweden increases, forcing the supply-structure of Holmen to face two important challenges. Firstly, it is of the outmost strategically importance to secure the long-term supply of Norway spruce pulp wood to the industries. Secondly, Holmen desires to increase the obtainable volume of Norway spruce pulp wood. This would enable the company to choose volumes in the lower price-segments and thereby decrease the dependency of costly marginal volumes. As this work shows, one part in managing these challenges could be to lower the quality standards concerning root rot (Heterobasidium annosum). Facts presented in the work shows that: 1. Technically, the TMP-industry of Braviken can handle a much more rotted pulp wood than that used today, although the cost of refinement increases.

This master thesis consists of an investigation of the profitability per hectare in privatly owned forest land. The investigation is based on data collected from Skogsstyrelesen, Riksskogstaxeringen and Skogsforsk. During the last twenty years the prices on pulp wood and saw log have substantial decreased, but during the same time the the volumes from final felling have increased and the cost for felling has decreased, this investigation shows how the netprofit per hectARE after final felling has changed between year 1980-2005 This investigation shows that that the netprofit has stayed on a stable level during the years 1985-2005 even though prices pulp wood and saw log decreased. Much indicates that the demand of swedish pulp wood and saw log will continue to be strong or even stronger wich will give increased prices and an higher netprofit after final felling in the future.

Fuel pellets are a refined bio fuel mostly consisting of residues from sawmills and wood industry. At Rindi Västerdala AB's combined bio energy plant in Vansbro fuel pellets are produced, while the waste heat from the process is used for district heating. The pellets are produced from sawdust, wood shavings and dry wood chips that is dried, milled and pressed into small cylindrical rods. The advantage of refining the wood material in this manner is that the energy value is greater per unit volume and unit weight, thereby the cost of transportation per energy unit is reduced. Also, less storage space is needed.Pellet manufacturing is a complex process since many parameters affects the final results.

The background for my thesis is the fact that with rising electricity and oil prices it becomes interesting to calculate on alternative heating systems. I have chosen to calculate upon my parents? farm, which today heats the dwelling house with wood. This is very time-consuming work, time which could be spent on other work. The main objective for this study is to compare three different heating systems to decide how they differ considering effort and cost. The result from the calculations was that grain-heating system demanded the least amount of work, but the total cost was a little higher compared to chips heating. Chips heating required half as much work as today?s wood heating and had a little lower total costs compared with the corn heating. Which system to choose largely depends on how the own work is valued.

The purpose of this study is to explain how the value of sawn wood changes when sawn wood are cut in 30 respective 60 cm lengths. The raw material into the saw mill will mainly be bucked in 30cm and 60 cm modules. There will also be two alternatives where the timber will be bucked special lengths, 370, 490 and 550 cm but also in 490 and 550 cm.The method used for the study is to simulate both cutting and sawing the woods. For cutting the simulator Timan is used and for sawing the simulator Timberopt is used. When data is generatedfrom the simulators, calculations of some key figures is done and also how much the revenue need to be increased for the sawn wood in order to cover for the increased costs of changing sawn woodfrom 30 cm to 60 cm modulesThe conclusion is that the single biggest reason, impacting the value of the sawn wood is the cutting at the saw mill.When going from 30 to 60 cm modules, the impact will be that the customers to the saw mill must pay more to increase the revenue by at least 10% for the sawn wood in order to justifice the changein production.It is also possible to increase the value of the products further by bucking the timber in three lengths, 370, 490 and 550 cm, in order to get 12 % increase of the share of longer sawn wood (>= 480 cm)..

Fire is an important ecological factor, but its consumption of coarse woody debris, CWD, has hardly received any attention. In this study, I investigate the consumption in relation to the time of initial flame exposure and propensity for continued combustion of standing CWD of pine (Pinus sylvestris). Two types of CWD were studied. Firstly, wood that had been dead for one to ten years. Secondly, wood that had been dead for several decades. In the burning experiments, logs of approx.

Since prehistoric time man has used wood to build their environment. The material?s availabilitycombined with its good mechanical properties has often made it the material of choice. Like allmaterials exposed to natures degradative processes the properties of wood decreases over time.Rot, UV radiation and attacks by insects and pests damage wood if not protected. Since we wantwhat we build to consist, optimizing our building materials durability is of great interest.Techniques and methods for increasing the endurance of wood have been developed in severaldifferent places and for a long time.