The Swedish pulp and paper industry meets higher demand for energy efficiencyi mprovements with increasing energy prices and changes in the Swedish renewable energy certificate system. One action of energy efficiency improvement is by using secondary heat, that otherwise would have been treated as waste heat, for use in a system with lower temperature demands. The aim of this Master´s thesis is to identify possible secondary heat sources in a typical Swedish pulp and paper mill and to investigate what economic benefits the secondary heat will provide when being used for pre heating of wood chips to a kraft digester.The Master´s thesis focuses on three secondary heat sources; dry warm air, warm water and moisture saturated warm air located inside the pulp or paper mill. Two types of kraft digesters are simulated within this study, a typical Scandinavian digester and a modern twin vessel steam phase digester.Due to quality aspects and low temperature level drying is the drying technology with dry warm air rejected. Using warm water in direct contact with wood chips increases the quantity of water to the evaporation plant and thus reduced pulp or paper production and is therefore also rejected.

Biodiversity is essential for human well-being and it is defined as the genetic variation within species and the variety of species and ecosystems. Biodiversity provides several ecosystem services which are necessary for human beings but there are different threats towards the biodiversity. The biodiversity linked to the forest in Sweden are threatened, about 50 % of the red-listed species in Sweden are associated with forests. This is linked to the commercial exploitation of the boreal forest in Sweden which started 200 years ago. The forestry the last 50 years, with clear-cuts, have contributed to a fragmented forest landscape.

This report presents suggestions and recommendations on how to convert an old industrial building, built in 1958, to an office hotel. One of the main criteria was that the floor plan should be flexible. The building is situated at Jonsereds Fabriker and the study was conducted for Hantverkslokaler i Göteborg AB, the estate owner.The survey is initiated with study visits at various office hotels, together with studies of literature regarding office planning. One conclusion from the study visits is that meeting-places, where the different companies can meet and exchange ideas and services, are important. Another one, and probably the most important parameter when planning offices is that they should have windows.

Vida Skog is supplying the whole Vida Ltd?s mills with wood raw material. This study aims to evaluate Vida Skog?s contractors and the relatively new contractorportal and to identify measures that are important for the contractors? skills. The purpose with the portal is to facilitate co-operation between contractors and buyers by streamlining the logistics of the whole wood supply process.The study was conducted in the form of a questionnaire.Most of the respondents were positive to the portal.

This survey was made to investigate the possibility of using an alternative method of fencing inSwedish forestry. The most common way of fencing in Sweden today is made by a two meter highmetal net that is attached to turned impregnated poles. The fencing methods that have beeninvestigated is a fencing system made completely out of wood so called ?German wood fence?.Browsing of game in forest regeneration areas is often a big problem and some kind of protection ofthe plants is often necessary. There is several ways of building fences and the most common way isto use metal nets and impregnated poles, this leads to a problem when the fence has profiled itspurpose.

When constructing a building, a number of aspects must be harmonized in order for it to fulfill requirements ? a building must fulfill requirements such a load-bearing, conservation of energy and a good indoor environment by means of, among other things, moisture proofing .Moisture problems in buildings can affect health negatively. As we are increasingly staying in indoors, demands on a good indoor environment are higher.This work starts with examining moisture problems in slab-on-ground solutions, and then links the various scenarios to moisture problems in a concrete slab of a real building. The building with moisture problems is located in Årby by in Borlänge and moisture damage was found in the slab at an apartment adjoining wall.By reviewing literature written within the field of moisture problem, making hand calculations and modeling in the program Comsol Multiphysics, judgments are made to find explanations as to why the rise of moisture occurred in the building in Årby by.Generally, the following guidelines may be used to reduce the risk of moisture problems in slab-on-ground constructions:Drying of construction moisture before laying the floor material.Using draining layer beneath the slab, to prevent capillary suction.Using insulation under the slab, partly for comfort and to establish the temperature difference between the ground and the concrete slab.Avoid direct contact between the wood and concrete, due to degradation and fouling smells that normally occurs.If necessary, use additional vapor barrier.In addition to the above, there are various methods for moisture-proof and moisture-monitoring by design or by the method ByggaF suited for the entire construction process various events..

Value stream mapping is a tool that is frequently used by many different companies. It is a great tool used to achieve the work that follows the theories of lean production. The tool is used, however, only frequent on the factory floor and the method is also designed based on this type of use.An interest of applying the method on administrative parts of the company has occurred lately. Administrative parts of the company refers to the part that does all the planning such as purchasing, receiving orders, customer contact, contact with factory floor and other work that is made around the actual manufacturing. But the knowledge about applying value stream mapping on the planning part of the company is lacking because the method is relatively new.In this work, a comparison is made between the introduction of value stream analysis on production and planning.

Value stream mapping is a tool that is frequently used by many different companies. It is a great tool used to achieve the work that follows the theories of lean production. The tool is used, however, only frequent on the factory floor and the method is also designed based on this type of use.An interest of applying the method on administrative parts of the company has occurred lately. Administrative parts of the company refers to the part that does all the planning such as purchasing, receiving orders, customer contact, contact with factory floor and other work that is made around the actual manufacturing. But the knowledge about applying value stream mapping on the planning part of the company is lacking because the method is relatively new.In this work, a comparison is made between the introduction of value stream analysis on production and planning.

For a long time the Swedish forests were used by the landowner?s mainly for providing wood to the household itself. The wood was not, to a greater extent, considered a product to be sold. During the 1800s the industrial era led to a demanding need for wood in the industry and thus the use of forest, forest production kicked off. The forest production was not regulated by law, which led to a differentiated forest production over the whole country without consideration of re-growth.

This report presents suggestions and recommendations on how to convert an old industrial building, built in 1958, to an office hotel. One of the main criteria was that the floor plan should be flexible. The building is situated at Jonsereds Fabriker and the study was conducted for Hantverkslokaler i Göteborg AB, the estate owner.The survey is initiated with study visits at various office hotels, together with studies of literature regarding office planning. One conclusion from the study visits is that meeting-places, where the different companies can meet and exchange ideas and services, are important. Another one, and probably the most important parameter when planning offices is that they should have windows.

The study of the French market for softwood has been done in collaboration with VIDA AB. The aim of the study was to investigate important product quality and service quality dimensions, the customers? perception of the offering and generally describe the French market and present actors. The market for softwood around the world changes over time and new markets can mean opportunities for the sawmilling industry. The French market is the second biggest European market for softwood, has had presence of actors with sourcing of raw material from the Nordic countries for decades and there is a growing interest for building with wood. Theory being used is about the different dimensions that make up the total quality of softwood, together with intangible dimensions making up the total offering that helps the sawmilling industry to create positive perceived value for the customers. Methodological approach in the study was a case study research design, aimed at providing knowledge about one specific subject in one context. The general description was mostly carried out by literature studies and data from various statistics sources.

This survey was made to investigate the possibility of using an alternative method of fencing inSwedish forestry. The most common way of fencing in Sweden today is made by a two meter highmetal net that is attached to turned impregnated poles. The fencing methods that have beeninvestigated is a fencing system made completely out of wood so called ?German wood fence?.Browsing of game in forest regeneration areas is often a big problem and some kind of protection ofthe plants is often necessary. There is several ways of building fences and the most common way isto use metal nets and impregnated poles, this leads to a problem when the fence has profiled itspurpose.

When constructing a building, a number of aspects must be harmonized in order for it to fulfill requirements ? a building must fulfill requirements such a load-bearing, conservation of energy and a good indoor environment by means of, among other things, moisture proofing .Moisture problems in buildings can affect health negatively. As we are increasingly staying in indoors, demands on a good indoor environment are higher.This work starts with examining moisture problems in slab-on-ground solutions, and then links the various scenarios to moisture problems in a concrete slab of a real building. The building with moisture problems is located in Årby by in Borlänge and moisture damage was found in the slab at an apartment adjoining wall.By reviewing literature written within the field of moisture problem, making hand calculations and modeling in the program Comsol Multiphysics, judgments are made to find explanations as to why the rise of moisture occurred in the building in Årby by.Generally, the following guidelines may be used to reduce the risk of moisture problems in slab-on-ground constructions:Drying of construction moisture before laying the floor material.Using draining layer beneath the slab, to prevent capillary suction.Using insulation under the slab, partly for comfort and to establish the temperature difference between the ground and the concrete slab.Avoid direct contact between the wood and concrete, due to degradation and fouling smells that normally occurs.If necessary, use additional vapor barrier.In addition to the above, there are various methods for moisture-proof and moisture-monitoring by design or by the method ByggaF suited for the entire construction process various events..

Environmental destruction is a growing problem in our world. Almost every day there are new reports concerning that we have to do something about the greenhouse gasses. Simultaneously is the human constantly more eager to have a life with higher standards and therefore uses more energy. The environment is a question that is highly up-to-date and more people try to find solutions on how to save our planet. One way to decrease the energy demand is to build passive houses, where the houses don?t have any active heating.

I samband med att intresset för att bygga högre trähus har ökat så krävs nya lösningar för att t.ex. kunna möta efterfrågan på stora öppna ytor och långa spännvidder. Träbjälklag med lång spännvidd har dock oftast svårigheter med att klara kraven på svikt och vibrationer. Ett nyutvecklat förslag på träbjälklag som förmodas klara dessa krav bättre än traditionella träbjälklag har varit utgångspunkten för detta examensarbete där syftet har varit att undersöka bjälklagets styvhet. Detta gjordes laborativt genom att bygga och testa en prototyp av det föreslagna bjälklaget och genom att en numerisk modell baserad på finita element metoden togs fram och användes för att studera hur olika parametrar påverkar bjälklagets styvhetsegenskaper.Bjälklagets design bygger på fackverksprincipen i primärriktningen och på balkverkan i sekundärriktningen.