An analysis of a specific application of anaerobic wastewater treatment at a pulp and board mill, Stora Enso Skoghall, was carried out. A literature study was done and effluent wastewater from CTMP pulp production was analyzed. The analysis consisted of a broad constituent analysis and an anaerobic treatment trial. Results from these test where used to calculate the treatment effectiveness and resulting energy potential at the mill.The literature study and constituent analysis showed that toxicity of the water to be treated, due to wood extractives and sulphur content, was of concern. Detoxification chemicals targeting these constituents where used in the anaerobic treatment trial.

ITT Water & Wastewater (före detta ITT Flygt) tittar på att eventuellt genomföra en förbättring av ytbehandlingen av deras pumpar för att eliminera de rostangrepp pumparna utsätts för idag. Examensarbetets uppgift är här att analysera och beskriva miljöeffekterna av de nya ytbehandlingsmetoderna som företaget undersöker.Målet med studien är att få fram ett underlag och en rekommendation om vilken ytbehandlingsmetod företaget bör välja ur miljösynpunkt.De olika metoder som studerats är:? Järnfosfatering + ED-lackering? Zinkmanganfosfatering + ED-lackering? Oxsilan + ED-lackeringDessa metoder har jämförts med nollalternativet, vilket innebär att samma metod som tillämpas idag fortsätter att användas.Miljöeffekterna som studerats för de olika metoderna är:? utsläpp till luft och vatten? avfall? energiAv de tre nya metoderna samt nollalternativet är Oxsilan följt av ED-lackering det alternativ som ger minst påverkan på miljön. Metoden har inga utsläpp av flyktiga organiska ämnen till luft, inget farligt avfall bildas och det avfall som ändå bildas är litet. Metoden har även lägre energiåtgång än de andra studerade metoderna.2008:Nr 2 Teknik.

Sewer trenches usually contain material with a higher hydraulic conductivity then the adjacent soil. Thus they can serve as paths of preferential flow in a polluted area. Wastewater from factories can also leak from wastewater pipes and pollute the soil in the sewer trenches.The purpose of this project was to investigate pollutions in sewer trenches and in sewer pipes in the industrial area of Köpmanholmen, 20 km south of Örnsköldsvik in the north of Sweden. To make an estimation concerning the potential of transport of pollutions in sewer trenches, hydrological calculations were performed.Leakage to any greater extent did not seem to be a problem in the area. This is the case both for the concrete and the wooden pipes that have served as factory wastewater pipes.

SAMMANFATTNINGÖvergödning har de senaste åren blivit en stor och omdebatterad fråga i många EU- länder.Även om problemen har minskat en del är detta inte tillräckligt, vi ser fortfarande fiskdöd,syrefria bottnar och giftiga algblomningar. Hur långt ska vi gå för att kunna övervinnaövergödningsproblemen? Genom olika sorters lagstiftning, ekonomiska styrmedel ochrådgivning har vi nått en bit på vägen, men fortfarande krävs det mycket arbete innan vi haruppnått målet. Jordbruket har pekats ut som en av de största källorna till övergödning pågrund av överskottet av kväve och fosfor som varje år urlakas ur våra jordbruksmarker.Inom EU finns sedan 1991 en gemensam lagstiftning; Nitratdirektivet. Syftet med direktivetär att minska nitratföroreningar och andra föroreningar från jordbruket, då dessa påverkarsåväl yt- och grundvatten som kust- och havsvatten.

Fartyg använder sig av stora dieselmotorer för framdrift och för att producera elektricitet ombord. Motorerna samt diverse kringsystem har behov av kylning och till detta används kemikaliebehandlat vatten i ett slutet kylsystem. Vid tömning och läckage från systemet tenderar det kemikaliebehandlade vattnet att hamna med länsvattnet. Länsvattnet genomgår en reningsprocess innan det pumpas överbord. Denna reningsprocess är inte utformad för att avskilja kemikalier och dessa tenderar att hamna i havet.

Uppsats för avläggande av filosofie kandidatexamen iKulturvård, Bebyggelseantikvariskt program15 hpInstitutionen för kulturvårdGöteborgs universitet2015:23.

For many years, the construction industry in Sweden has not developed much of an integral approach for design across disciplines. The sector?s impact on society, economics and environment is huge. To make the interactions within the construction industry more efficient, a relatively new concept called BIM (Building Information Modeling) has been introduced. The idea with BIM is that the different actors of the construction industry will work through intelligent CAD software, with common file formats and more cooperation between different actors during the various steps of the building and construction process.The technical consultancy company WSP Sweden is working actively to implement BIM within the frame of its activities.

The report comprises two separate parts:part 1:  Temperature needs for district heating in the paint shop for axles in building 210part 2:  Energy and low temperature waste heat solutions in heating and cooling systems for   building 64 with surroundingsThe paint shop for axles in part 1 has air quality requirements in places for coating of axles. Toachieve desired air properties there are different process ventilation systems, which consist ofventilation coils for heating and cooling, plus air humidifier. The ventilations coils for heating usedistrict heating. Today the ventilation coils use water of 100°C to achieve necessary air demands inthe coating boxes. This part of the report investigates whether the existing system would achievethe air requirements with a water temperature of 75°C instead of 100°C in the ventilation coilsduring the coldest parts of the year.

Ground construction has to a large extent been dominated by traditional meth-ods during the last 50 years. Although the construction has been changed meanwhile innovations are not accepted. In collaboration with NCC Ltd Region South, I have examined a modern con-struction methodology that has been developed by NCC for future large pro-jects. The method is divided into two central phases. Phase 1 is? Single Pro-duction? which is a preliminary period for ground constructions to come.

Biogas is a renewable energy source that is produced by anaerobic digestion of organic mate-rial. In Sweden, biogas predominately comes from sewage water sludge and landfills or from organic waste of households and industries. Small scale digestion plants at farms are espe-cially expected to contribute to increased biogas production in the future. Biogas can be ob-tained directly in it?s raw form and used as fuel in a combustion chamber.

This bachelor?s project deals with both the problems of high water temperatures in fishponds at a fish-breeding station and of the nutrient load to nearby lakes and streams in Harasjömåla, Blekinge, Sweden. Theory, methods and results of the analyses are presented in the report..

This thesis conducted at the University of Uppsala investigateshow well a prefabricated building component from the manufacturerMasonite Lättelement AB can be incorporated into ahouse projected to accomplish the demanding criteria of a passivehouse. The thesis is organized as a comparison betweenthe prefabricated elements and an on-site built component fromthe passive house area of Oxtorget in Värnamo, Sweden. Theaspects investigated were air leakage, energy, moisture, economyand noise conditions.Results of the comparative analyzes shows that the prefabricatedproducts were capable of accomplishing the requirementsof passive houses and therefore this thesis should beviewed as a basis to confirm that the technology of prefabricatedbuilding components today in Sweden are mature enoughto be a significant part of the passive houses that are to be builtin the near future. The development of prefabricated technologyis of crucial significance if we are to accomplish the goalsof reduced energy consumption by the year 2020..

There are records of lowering of the water level in a lot of the Swedish lakes from the middleof the 1700th century. The aim was gaining more areable land to meet the needs of more foodto support the expanding population. In areas with top soil which contents of clay or loam asin the southwest of Scania in southern Sweden this was proven to be a successful wayexpanding the total outcome of the harvest.The studied area in the northeast of Scania, though, consists of morain with a lot of mires -much less nutritious conditions. When the water level is lowered the atmosphere gets accessto the peat. The dissolving of the organic matter that has been suppressed by the lack ofoxygene below water level continues.

?Mechanical debridment ? A studie in irrigation optimization? is a final thesis which was executed by Fredrick Ekman, in close collaboration with the other group member Mikael Johansson, during the spring 2012. The thesis was carried out through Karlstad University Faculty of Technology and Science in the study program of Innovation and Design Engineering (180 ECTS credits). The client of the project was Medilink AB located in Lindesberg, and the contact person was Nils-Erik Söderström, Chief Executive Officer. The project was supervised by lecturer, Lennart Wihk, and examined by lecturer and professor Fredrik Thuvander at Karlstad University.

Forest streams and the associated riparian zones are sensitive to disturbances and changes that occur within these riparian areas. Particularly sensitive are small streams of low order, which will have large impacts down-stream. The disturbances that occur in the riparian zones are reflected quickly in the stream. Driving with forestry machines in the riparian zone will have detrimental effects to the soil and water. Driving the machines will lead to changes in the mineral soil composition, resulting in the reduction of porosity, less infiltration, compaction, and an increased bulk density.