The construction industry is always looking for ways to make the work more efficient aswell as minimize the waste of money in general. At the same time the industry is showing alow awareness of logistics which has to increase in order to improve the industry in thesekind of questions. Projects located in the inner city have high demands on the logistic andthe handling of material due to the so often limited space for storages of the material. Dueto this the purpose of this report is true a case, study and analyze what kind of factors thereis to take into consideration during the materials way from the supplier to the workstationin a project located in the inner city. The data for the report was collected with the help of acase study, and in three different ways.

This project aims to investigate whether algae can be used for biodiesel production in Italy. Algaes are a good option since they are fast growing and do not occupy arable land. The aspects that have been considered are growing, harvesting, which algae strain that is most suitable, extraction of oil, the production of biodiesel and where in Italy this could be possible due to climate. Cost? and energy calculations have been made to investigate if biodiesel produced from algae would be profitable. During the production of biodiesel there are several residues obtained. When the oil has been extracted from the algae, biogas is produced from the residual biomass by anaerobic digestion and then the electricity that can be produced is supplied to the production of biodiesel.

It takes a very long time for ionizing radiation of used nuclear fuel toreturn to a natural background level, for this reason one of the requirements for theselection of the location of a repository was that the environment as well people'shealth would be protected from the harmful effect of radioactivity. This requirementmeans that the waste must be isolated in a geological formation. In Sweden therepository will be built in the crystalline bedrock. The location for the Swedish nuclearfuel repository at nearly 500 meters depth at Forsmark in Östhammar was decided 3June 2009. The repository will be located at Söderviken, close to the Forsmarknuclear power plant in a 1.90 billion year old bedrock that will accommodate 12,000tons of spent nuclear fuel.

This report presents the results of a thesis in which the department PL Hus at Grontmij AB isstudied. The study has been done in order to locate problem areas in order to streamline andimprove the quality of working. The study was done by an engineering student from theDepartment of Industrial Management at KTH on behalf of Grontmij AB. The project extendedover a period of 20 weeks during spring 2011.In addition to the Department itself has two project managers in two different projects beenfollowed. The method used has been participant observation and was used to be able to comeclose to reality and thus find problem areas where there are opportunities for development.Validation was made through comments and opinions from workers at Grontmij AB, afterreading the reports analysis.Based on a system and holistic approach has parallels been drawn to the production systems suchas TPS (Toyota Production System) and lean production.

The dishwasher is a wide spread product that occurs in many households. It saves the user time,water and energy. When using a dishwasher instead of doing dishes by hand a lot of energy issaved.The importance of lowering the energy consumption does not only come from the consumerwinnings but also from an environmental point of view. Scientists are certain that the globalwarming comes from the emission of green house gasses that is created by human consumptionof oil, gas and coal.Dishwashers today are a lot more energy efficient than older dishwashers, but there are stillmargins to lower the energy consumption. The aim with this project is to investigate thedishwasher and it?s washing cycle, noting different phases and components that contribute towaste of energy.

The construction industry is always looking for ways to make the work more efficient aswell as minimize the waste of money in general. At the same time the industry is showing alow awareness of logistics which has to increase in order to improve the industry in thesekind of questions. Projects located in the inner city have high demands on the logistic andthe handling of material due to the so often limited space for storages of the material. Dueto this the purpose of this report is true a case, study and analyze what kind of factors thereis to take into consideration during the materials way from the supplier to the workstationin a project located in the inner city. The data for the report was collected with the help of acase study, and in three different ways.

It takes a very long time for ionizing radiation of used nuclear fuel toreturn to a natural background level, for this reason one of the requirements for theselection of the location of a repository was that the environment as well people'shealth would be protected from the harmful effect of radioactivity. This requirementmeans that the waste must be isolated in a geological formation. In Sweden therepository will be built in the crystalline bedrock. The location for the Swedish nuclearfuel repository at nearly 500 meters depth at Forsmark in Östhammar was decided 3June 2009. The repository will be located at Söderviken, close to the Forsmarknuclear power plant in a 1.90 billion year old bedrock that will accommodate 12,000tons of spent nuclear fuel.

The purpose of this work is to study a circulation project in Enköping municipality, where the society?s rest products are used to make beneficial products. In Enköping the rest products from waste treatment plants and private sewers are used to fertilize and irrigate Salix plantations that later are harvested and burned at the local combined heating and power plant, ENA Energy AB, to produce electricity and heat. Possibilities to apply this kind of project ona municipality in Russia are also explored.Guryevsk municipality in Kaliningrad region was chosen since there is a need to improve energy systems and reduce emissions to water and air. This municipality strives to become environmentally friendly.

In Sweden, a big part of the energy use is used in the housing sector. Political goals and targets are set up which the housing sector needs to work towards. Apartment buildings are a major part of the housing sector in Sweden and therefore reduction of energy use in these kinds of buildings are key to lower the energy use in Sweden. But there are not only political incentives to reduce the energy use. Some energy?saving measures are directly profitable and should thus be performed.

Many of todays studies show that district heating is one of the betteralternatives as heating source because of its low environmental load.The energy source is often leftovers from other processes producing energy or waste, like garbage or chips.Electricity in combination with geothermal heating is another heating system that has increased sharply during the last years, and also this system decreases the discharges that have negative affectson the environment compared to several other heating methods.This report aims to, concentrated towards these two different heating systems, estimate the amounts of discharges they indirect cause and how the environment is affected.We have calculated the mean value for discharges of carbon dioxide, nitrogen oxide, sulphur oxide and dust generated from electrical power used in Sweden.Through interviews and research we have gained data for the same substances that district heating based on combustion of garbage and biofuel generates.We have also in cooperation with a housing company chosen a building we see representative for many of the new single-family houses built in Sweden today.Based on its shape and appearance we theoretically created three alternatives of the same house, each of them with climate screens different from each other.Together with the amounts of discharged environmental affecting substances, these houses were the base for our calculations and studies when investigating the different heating sources environmental effect.The results have thereafter been analyzed and discussed from different angles..

Odling av mikroalger för framställning av biogas är ett relativt outforskat område. Den forskning som hittills utförts har påvisat lovande resultat tack vare möjligheten att utnyttja resurser som idag går till spillo, eller till och med utgör miljöproblem; mikroalgerna kan rena både näringsrikt vatten (exv. avloppsvatten) och koldioxidutsläpp (rökgaser från industrin) då de tar upp föreningar innehållande kväve, fosfor och kol från dessa källor. Den producerade biogasen kan ersätta fossila bränslen. Dessutom skapas en rötrest som kan återföras till odlingsmarker vilket sluter näringskretsloppet.

Biogas är en förnyelsebar energikälla som tillverkas genom att organiskt material som matavfall bryts ner av mikroorganismer under anaeroba (syrefria) förhållanden. Regeringen har satt upp mål för en högre matavfallsutsortering vilket leder till ökad mängd tillgängligt substrat till biogasproduktion.Matavfallet som samlas in börjar brytas ner under tiden det transporteras och lagras. Syftet med studien var att undersöka hur länge matavfall lagras, ta fram ett representativt recept på ett genomsnittligt matavfall i Sverige och utvärdera hur mycket metanpotential som försvinner från matavfall med avseende på lagringstid, insamlingssystem (papper- och plastpåse) och lagringstemperatur (22°C och 6°C) genom laboratorieförsök.Den genomsnittliga lagringstiden för matavfall från villor och flerbostadshus i undersökningen var sex dagar. Ett recept för matavfall har tagits fram med hjälp av litteratursökning och modifiering av recept i Avfall Sveriges rapport U2010:10. Laboratorieförsöken visade att skillnaden i metanpotential mellan plast och papper var tydlig vid 22°C, då metanpotentialen sjunker, men obefintlig vid 6°C.För att uppnå maximal metangasproduktion från matavfall under den varma delen av året så är plastpåsar bättre då de har en mer konserverande effekt på matavfallet än papperspåsar.

To meet the needs and demands of the costumer, accurate information about how much is available in stock is necessary. When the information in the system does not match the physical inventory, inventory inaccuracy occurs. Inventory inaccuracy is common among companies and may contribute to increased labor cost, excess inventory, production disruptions, waste of time, late deliveries, poor service and lost customers.The purpose of this study is to identify contributing factors to inventory inaccuracy for business with outdoor storage. The study also aims to investigate how efficiency factors can reduce the inventory inaccuracy for business with outdoor storage.A case study was conducted to answer the purpose. A company in the steel industry was chosen to examine inventory inaccuracy on business with outdoor storage.

In an ever more competitive environment Sandvik Materials Technology,SMT, runs a large-scale program to improve their processes for product development.The purpose with the program is to increase the company?s profitability by increasingthe number of new products in their product portfolio. The strategies SMT is usingfor reaching their goals are to change the way they work with product development byreducing lead time and learning how to prioritize products with the highestprofitability. In the R & D Department the work of improvement pursue by adaptingLean R & D to their way of working. Lean R & D encourages working withcontinuous improvements and eliminating waste.The main purpose for this Master?s Thesis is to develop didactic support to make iteasier to implement Lean in SMT R & D department.

The development of productivity in the construction industry has long been at a steady state compared to the manufacturing industry. Studies have shown that, amongst other things, waste on construction sites can reach up to one third of the total production cost. This has been observed from different aspects, and change is forthcoming.This thesis aims to provide a foundation for an increased productivity at production sites of building bridges. It is primarily based on a field study at Skanska, at a bridge construction site near Grängesberg. Via continuous interviews with the whole production crew, construction workers and management, information on interference and possibilities of improvement at the work site has been documented.