Voltage sag indices are a way of quantifying the performance of the power supply, as far as voltage sags are concerned. Indices can be defined for individual events, for individual sites, and for a whole system. A standard method for single-event methods is part of IEC standard 61000-4-30.This thesis emphasizes the importance of voltage sag indices and different methods for calculating three-phase voltage sag characteristics. Three-phase events measured in a medium network voltage over period of one month were analyzed, results examined and statistically evaluated. An algorithm for calculating voltage sag characteristics and indices was created in Matlab.

Voltage sag indices are a way of quantifying the performance of the power supply, as far as voltage sags are concerned. Indices can be defined for individual events, for individual sites, and for a whole system. A standard method for single-event methods is part of IEC standard 61000-4-30.This thesis emphasizes the importance of voltage sag indices and different methods for calculating three-phase voltage sag characteristics. Three-phase events measured in a medium network voltage over period of one month were analyzed, results examined and statistically evaluated. An algorithm for calculating voltage sag characteristics and indices was created in Matlab.

Voltage sag indices are a way of quantifying the performance of the power supply, as far as voltage sags are concerned. Indices can be defined for individual events, for individual sites, and for a whole system. A standard method for single-event methods is part of IEC standard 61000-4-30.This thesis emphasizes the importance of voltage sag indices and different methods for calculating three-phase voltage sag characteristics. Three-phase events measured in a medium network voltage over period of one month were analyzed, results examined and statistically evaluated. An algorithm for calculating voltage sag characteristics and indices was created in Matlab.

Voltage sag indices are a way of quantifying the performance of the power supply, as far as voltage sags are concerned. Indices can be defined for individual events, for individual sites, and for a whole system. A standard method for single-event methods is part of IEC standard 61000-4-30.This thesis emphasizes the importance of voltage sag indices and different methods for calculating three-phase voltage sag characteristics. Three-phase events measured in a medium network voltage over period of one month were analyzed, results examined and statistically evaluated. An algorithm for calculating voltage sag characteristics and indices was created in Matlab.

Detecting small signals with a comparator demands that the total voltage offset is lower than the actual signal. The total offset includes the voltage offset in the comparator and the voltage offset that is created by the offset currents that flows thru the load at the comparators input. The goal with this comparator that has been developed has been that it will have a total voltage offset at maximum 500 uV. The comparator does not need to be extremely fast or does not need to operate in a big frequency area. To have all the flexibility that is needed a full custom technique is used.

In this report we describe an adaptive simulated annealing method for sizing the devices in analog circuits. The motivation for use an adaptive simulated annealing method for analog circuit design are to increase the efficiency of the design circuit. To demonstrate the functionality and the performance of the approach, an operational transconductance amplifier is simulated. The circuit is modeled with symbolic equations that are derived automatically by a simulator..

The goal for this master thesis project has been to investigate the power quality in adistribution grid, which has a high fraction of dispersed power production due towindmills. The study has been done on a grid in Laholm South of Halmstad, whereapproximately 45 windmills are connected to the distribution grid owned by SHKEnergi. The investigation has been focused on to two radialy fed 20 kV lines, wheretwelve windmills are connected.Voltage variations have been studied by creating a model of the grid in the simulationprogram SIMPOW. The largest deviation that has been found in any point of the gridis ±1.9 % of the nominal voltage. This deviation is a result of varying powergeneration from the windmills and the voltage regulation at the connection point ofthe line.

The voltage regulation in Fortum Distributions medium voltage network in Stockholm does not work satisfactory. This results in too high distribution voltages with many customer complaints as a consequence. The reason is the model responsible for compensating for voltage drops in the distribution network. Despite several adjustments Fortum has not been able to find the source of the high voltages and has therefore appointed an investigation in the form of a thesis work.The aim of this investigation is to locate the error and to produce a proposal regarding the solution of this error using the existing system, common industrial knowledge, state of the art research and the option to use voltage readings from the different substations.The conclusion of this master thesis is that the largest contribution to the high voltage levels is made by the large compensation for distribution loses. Furthermore an additional error in the model has been found.

The goal for this master thesis project has been to investigate the power quality in adistribution grid, which has a high fraction of dispersed power production due towindmills. The study has been done on a grid in Laholm South of Halmstad, whereapproximately 45 windmills are connected to the distribution grid owned by SHKEnergi. The investigation has been focused on to two radialy fed 20 kV lines, wheretwelve windmills are connected.Voltage variations have been studied by creating a model of the grid in the simulationprogram SIMPOW. The largest deviation that has been found in any point of the gridis ±1.9 % of the nominal voltage. This deviation is a result of varying powergeneration from the windmills and the voltage regulation at the connection point ofthe line.

This master thesis has been performed at Vattenfall Power Consultant in Gothenburg and Trollhättan for Vattenfall Vattenkraft. In this report vacuum circuit breaker in small-scale hydropower stations with the rated power 4 MVA and below has been studied. Models of the stations are modeled and analyzed in PSCAD/EMTDC to study the high voltage transients that are created after current chopping with vacuum circuit breaker. Vacuum circuit breaker may chop the current before it reaches zero value, which means that high voltage transients can be created. The equipment of the stations can be destroyed by high voltage transients.The purpose of this thesis is to examine the use of vacuum circuit breaker in small-scale hydropower stations and the risk for high voltage transients from current chopping.According to the results there is a risk of high voltage transients after current chopping with small synchronous generators in stations with the operating voltages 0.4 kV and 3.6 kV.

The aim and goal of this work has been to design and implement a voltage reference network for a 12-bit PSAADC, Parallell Successive Analog to Digital Converter. A chip containing the design has been sent away for fabrication. Because of the long processing time, no measurement data are presented. The main specifications for the voltage reference generator is to generate stable reference voltages with low noise and a good PSRR. Efforts has also been made to minimize the power consumption..

Microproduction, also called distributed generation, is something that has become more and more popular in the electric grid. Microproduction can however lead to unacceptable performance if several units are installed in the same low voltage network. It is therefore good to know a limit where the performance of the low voltage network becomes unacceptable based on given parameters. This limit is usually called hosting capacity.In this report the hosting capacity with respect to voltage and current have been studied in three low voltage networks which are located in Falu Elnäts concession area. This has been done by simulations in a GIS-program where critical times of the grid have been simulated.

Minimizing power consumption is a critical part of many embedded design projects. Thechallenge is to limit the power consumption of the system and at the same time providesatisfactory service to the user. With regards to microprocessors, the main way of limiting powerconsumption during program execution is to adjust the frequency and the voltage at which theprocessor operates.To enable the implementation of real-time scheduling with support for dynamic voltage andfrequency scaling, an exhaustive study of the Freescale i.MX31 embedded microprocessor isperformed. Specifically, the power consumption relationship to all relevant frequency andvoltage settings is investigated. In addition, to enable frequency and voltage scaling in a real-timeenvironment, a complete timing analysis of proposed voltage and frequency scaling methods isperformed and their suitability for use in real-time systems is evaluated.To integrate voltage and frequency scaling capability into OSE RTOS, a software module hasbeen developed for this operating system.

Lärare använder sig av olika metoder för att hjälpa studenter att utveckla de verktyg de behöver för att lära sig engelska, eller något annat ämne. En metod här är muntlig feedback, som används för att uppmuntra elever eller korrigera dem när de utför språkliga fel. Vårt mål med detta examensarbete är därför att undersöka vilka typer av muntlig feedback som kan hittas i ett klassrum där man lär sig engelska som främmande språk och vilka attityder som både lärare och studenter kan ha gentemot muntlig feedback. Tre typer av undersökningsmetoder har använts: observationer, intervjuer och enkäter. Resultatet visar på att studenter förhåller sig positivt till muntlig feedback i klassrummet, särskilt explicit corrective feedback.

In this thesis a rural network in Norrbotten, Sweden, has been to designed and planned with the purpose of improving distribution reliability by exchanging existing overhead lines with underground cables. General network design considerations are discussed as well as the ones for the specific low voltage grid. During the design phase the maximum power of domestic consumers has been estimated using Velander?s method. Currents, voltage drop and impedance of the network have been calculated and fuse operation and selectivity has been considered.