Cost allocation ? a study of how Swedish energy companies allocate costs between electricity and district heating in a combined heat and power plant District heating is today the most utilized alternative for heating in Sweden. In a combined heat and power plant (CHP) electricity and heat are cogenerated. The environmental and economic advantages with this kind of production are high. A problem in a CHP-plant is to allocate costs between electricity and heat since both products are generated in the same process.

In this work an assessment of the compressed air system in the facilities of Vattenfall Heat Uppsala has been conducted. The facilities constitutes, among others, a combined heat and power plant, and two waste incineration plants. The compressed air is supplied primarily by seven rotary screw compressors and yearly electric energy consumption in these has been determined. Furthermore, the usage of compressed air has been mapped in order to find processes with energy savings potential. Several suggestions how to reduce the usage of compressed air have been presented, resulting in decreased need of electric energy and reduced CO2-emissions.The results show that total need of electric energy in the compressors, during a standard production year, amounts to 5.83 GWh.

The need for snow-free surfaces at squares, bus stops, platforms, car parks and sports facilities increases and at the same time energy price rise and the environment is becoming a hotter issue. The construction of the ground heating systems often lack thermal insulation under the heating pipes, which means that the heat from the pipes not only warm up the soil surface but also heats the surrounding soil. The insulation also has more features, by insulating the risk of frost damage is minimized. The goal of this report is to demonstrate the large heat loss and energy costs in the absence of insulation under the heating system.The report begins with a scientific way to study and treating the soil heating system uses, and the theory involved. Furthermore it also deals with different routing principles of heat pipes depending on the facility.All calculations are made with so called finite element method (FEM), in COMSOL Multiphysics 3,5a, where models are created with different conditions.

An investigation of the heat impact of laser cutting on the material properties when producing tensile and impact test specimens of different steel types of varying thickness has been performed. The purpose of the thesis project was to provide recommendations regarding how much material that needs to be milled from the laser cut edge before tensile and impact tests. The study has been performed partly by investigating the test specimens by heat camera when the specimens were cut in the laser cutting line and partly by performing hardness tests, investigation by microscopy, and tolerance and roughness measurements and tensile tests of the laser cut material and material produced in the traditional multi operation machine. The results show that the heat affected zone in the thicker materials is greater than previously thought of, and that the currently used recommendation has to be adjusted. The study clearly shows that the thicker the material, the greater the heat affected zone, independently of the steel type, since the thicker material takes longer time to cut.

ABSTRACT: Commercial swab transport systems are used for collection and transporting of fecal and other microbiological samples. This system must maintain viability and contribute to survival of microorganisms during transport to the laboratory. Four swab transport systems have been compared, eSwab, ?- Transwab and fecalSwab, all three with flocked swabs, and Copan Venturi Transystem with rayon swabs. The study followed the recommendations from the Clinical Laboratory Standard Institute; document M40-A for recovery of Samonella, Shigella, Yersinia and Neisseria gonorrhoeae after storage for 0, 6, 24, 48 and 72 h at room- (22-25°C) and refrigerated (2-8ºC) temperature.

The main objective of this research was to study how increased arterial oxygenation by the use of Pulsed Inhaled Nitric-Oxide (PiNO) influenced the metabolic and cardiovascular parameters on horses undergoing acute abdominal surgery because of colic. The parameters blood lactate, blood glucose, pH and heart rate were evaluated before and during anesthesia and closely after recovery. The study showed that blood lactate concentrations decreased significantly during anaesthesia in horses treated with PiNO compared to non-treated horses. It was also seen that the lactate concentration decreased most in horses with the highest levels before PiNO treatment. Since enhanced oxygen extraction ratio was evident in the PiNO group, improved oxygen delivery to the tissue may be a possible explanation for the improved situation.

The biogas plant Kungsängens gård, owned by Uppsala Vatten och Avfall AB, produces biogas and biomanure from organic household waste, food processing waste and slaughterhouse waste. In year 2012, 4.4 million Nm3 of biogas were produced from 25 200 tons of waste. Before digestion all substrate is sanitized by one hour?s pasteurization at 70°C in order to kill pathogens. Another method, integrated thermophilic sanitation (ITS), is of interest in order to decrease the energy demand.

This report was written by Lisa Bengtson and Hanna Paradis and describes the degree thesis "Environmental impacts of solid waste treatment in the Metropolitan Region, Santiago, Chile ? a comparison between current system and incineration with energy recovery". The purpose of this thesis was to investigate if incineration with energy recovery could be motivated through an environmental perspective as an alternative to landfilling of solid waste in Santiago, Chile. The study was performed with Life Cycle Analysis as a theoretical base. In Santiago, situated in the thirteenth region of Chile, Región Metropolitana, lives 6,5 million inhabitants. The major part of the solid waste produced in the region is landfilled on three different sanitary controlled landfills situated outside the city center.

AbstractThis master thesis was performed at Scania transmission department in Södertälje, where the manufacturing of gears is done. Today a large amount of manual handling is performed between the machining and the hardening process. Most of the manual handling is done at the heat treatment department. The purpose of this master thesis is to give a suggestion on how to reduce or eliminate the manual handling at the heat treatment department. The possibility to use the same packaging throughout the processes will also be investigated.

Heat and power stations are often in need of optimizations. A simulation model is a tool for findingways to optimize the plant. The scope of this diploma work is to develop a simulation model ofBoiler 5 at Mälarenergi AB. Boiler 5 is a circulated fluidized bed boiler that was taken into service inyear 2001. Among the included parts in the boiler are cyclone, convection part andINTREX-chambers.

AbstractThis master thesis was performed at Scania transmission department in Södertälje, where the manufacturing of gears is done. Today a large amount of manual handling is performed between the machining and the hardening process. Most of the manual handling is done at the heat treatment department. The purpose of this master thesis is to give a suggestion on how to reduce or eliminate the manual handling at the heat treatment department. The possibility to use the same packaging throughout the processes will also be investigated.

The automotive market is currently undergoing a historical change where stricter emission legislations and ever increasing fuel costs have intensified the search for effective alternatives to the conventional internal combustion engine, which has resulted in a substantial trend towards electrification of powertrains. Storage of electrical energy is the fundamental component in this technology where the lithium-ion batteries are currently considered as the most appropriate solution. Lithium-ion batteries, however, as other types of batteries, can only be used efficiently and durably within a specific temperature range.This Master thesis has been carried out in collaboration with Electroengine in Sweden AB, situated in Uppsala, which has an ongoing project regarding development of a modular battery system for electric powertrains. The project is at a stage where an initial prototype has been developed which provides the foundation for this thesis. The study has addressed the battery system performance from a thermal perspective, in order to validate the ability of the system to create a thermally serviceable environment for the lithium-ion battery cells.

Vattenfall Heat Uppsala runs the waste incineration plant in Uppsala, which produces district heating, process steam, district cooling and electricity. Vattenfall Heat Uppsala has decided to introduce an energy management system with the aim to increase the energy efficiency of the plant. The basis in such a system is to make an energy mapping.In this thesis an energy mapping has been performed at the waste incineration plant with the aim to identify and determine the size of energy flows. The investigated energy flows are used fuel, produced and used steam, produced district heating and cooling. Also the use of electricity to run the processes has been investigated.

We have the tradition in Sweden to build villas and houses with a wooden framework. It has become natural for us because we have so much forest in our country. Building with wood has advantages, it is easy to process, but also disadvantages, as it is sensitive to moisture.Finland has long made use of the thermal blocks to build villas. It is a type of bricks that are a bit like a sandwich element, with a core of EPS and concrete on both sides of the core material. The concrete is hollow, so that after the walls has been bricked up you pour concrete into the hollow bricks.The issue of this report is to find out if concrete can be an alternative to wood as framework material in villas.

AbstractThis master thesis was performed at Scania transmission department in Södertälje, where the manufacturing of gears is done. Today a large amount of manual handling is performed between the machining and the hardening process. Most of the manual handling is done at the heat treatment department. The purpose of this master thesis is to give a suggestion on how to reduce or eliminate the manual handling at the heat treatment department. The possibility to use the same packaging throughout the processes will also be investigated.