The Goal with this Master of Science thesis is to expand the possible turbine efficiencymeasurements on an exhaust turbocharger. It was done as a part of the CICERO competencecentre. To feed the turbine with air a special flow rig has been used. Instead of loading theturbine by just restricting the compressor flow a docking system for an electrical dynamometer isdesigned to use the dynamometer as an additional loading source. By using an electricaldynamometer as loading device for the turbine, measurements are not depending on compressorperformance.A large part of the work consists in designing accessories for the dynamometer.

The power system modelled in this thesis work has been developed for simulationwhen e.g. the production in some part of the power system is changed. The powersystem has been modelled according to the swing mass of the system, the frequencydependency of the load and the turbine governor. The model determines the systemfrequency, the period of regulation and the power exchange between the differentsubsystems in the Nordic synchronized system.In this model the system frequency is assumed to be the same in all different parts ofthe power system and the voltage conditions in the power system are neglected. Forthat reason power swings does not occur between different subsystems in the powersystem, which usually occur as a result of the swinging connection between thetransmissions line.

This study presents a methodology that enables the annual average power of a wind turbine to be increased by automatically optimizing it?s airfoil, twist and chord dis- tribution. As a part of the study the software SiteOpt has been developed. This software connects the open source software XFOIL with the blade element momen- tum theory. XFOIL gives lift and drag coefficients which enable the blade element momentum theory to predict the power of a wind turbine at different wind and ro- tational speeds.

The expansion of the Swedish hydro power has contributed positively to the reduction of the environmental impacts from the fossil fueled power production. In the same time the extensive expansion has been proved to cause negative ecological and local environment impacts of a stream. This, in turn, has been affecting the biodiversity and fish stock negatively, which has been reduced. One of the underlying problems is the lack of possibility for the fish to pass the plants, but it is also directly correlated to the mortality rate of the fish passing through the turbine, which this study is investigating.The mortality rate has been computed for three different locations in Sweden, Untra, Tännfallet and a third one whose location is confidential, and is denoted as Case 1, 2 and 3. The model used to calculate the mortality rate in this investigation is based by existing blade strike models and knowledge and are investigating the death due to mechanical injuries from collision with a runner blade in the turbine.

The purpose of this master thesis is to investigate how nearby forests affect the energy production in wind turbines. To reach the purpose a case study is performed on three wind turbines sited on a field in a north-south line at Andersfält in the municipality of Halmstad, Sweden. Approximately 100 meters south of the southern wind turbine a forest is situated. The case study is divided into three sub studies where the difference in energy production, the affect of the forest and a wind meteorology model, WAsP, is studied. The result show that the forest have a significant influence and that the WAsP-model gives an incorrect result of the energy production in wind turbines sited near a forest..

Today produces the wind power 2,5 TWh (TWh = terawatt hours) of Sweden?s total energy input of around 620 TWh. The Parliament has adopted a national planning objective where the wind-based electricity production will increase to 30 TWh in 2020. This requires that landowners will leas there land for wind power to wind energy companies. Such land leasing means that the landowner's business is considered to be a multiple-use.

In Sweden there are 1894 small-scale hydropower plants in operation, which together generate 4.3 TWh of electricity per year according to Swedish hydropower compound (SVKF, 2011). This corresponds to the annual consumption of about 860,000 Swedish households (based on an annual consumption of 5000 kWh). In the mid-1950s there were around 4000 small-scale hydropower plants in operation in Sweden before cheap fossil fuels and uranium competed with them, in the current situation only 1,894 of these are in use. If slumbering small hydropower plants once again would be taken into use and some new ones are built, we would be able to extract about 7 TWh of renewable electricity from these annually in Sweden, representing about 1.4 million households.The thesis intends to calculate and construct a hydroelectric power plant at the existing dam in Olofsfors and give suggestions on how the power station should run during the time that fish migration is greatest in Leduån.The turbine and generator to the station in Leduån at Olofsfors is designed by the height of the fall and the water flow through the dam. The turbine selected for the station is a CK-1000RM turbine with a 4-pole 250 kW generator from Cargo & power turbine Sweden AB, which is expected to deliver 1.2 GWh per year.

This master thesis project at KTH is performed in the Mechanical and Aerospace Engineeringdepartment at University of Florida (UF). The thesis is a small part of a gas turbine researchproject where a vapour absorption refrigeration system (VARS) and a high pressure regenerativeturbine engine (HPRTE) are integrated together. The main objective is to build a computermodel of the VARS. The computer model is supposed to be used to analyse the off-designperformance of the VARS and should also be easy to integrate as a subroutine in a more complexsystem model. To model the VARS some knowledge of the absorbent/refrigerant mixture had tobe well known, in this case a mixture of ammonia and water.

The exhaust arrangement on a Scania V8 consists of one manifold at each bank connected to a twin entry turbine (8-2-2). A study in GT-Power has shown improved performance and reduced cylinder to cylinder variations using two manifolds at each bank in combination with a single entry turbine (8-4-1). This thesis work analyses the difference in performance shown in simulation and verify it by engine test.The initial work was focused on simulation in GT-Power. Investigating how exhaust manifold volume and pulses effects the turbine efficiency and the mean effective pressure during the gas exchange. To verify GT-Power simulations four engine tests with different exhaust arrangement have been made.The results from GT-Power simulation indicate that a larger exhaust volume improve the turbine efficiency.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.