Finnhamn is a group of islands that are located in the middle north part of Stockholm?s archipelagos. On the main island Stora Jolpan there is a camp called Sommargården, which consists of eleven different buildings in various sizes. The assignment given by the Archipelago foundation (Skärgårdsstiftelsen) is to analyze if it?s benefited to replace Sommargårdens current heating system that consists of electricity radiators, with a more energy efficient heating system. This research is done with help of the literature review and a visit to Finnhamn in order to map Sommargården?s current state and its energy usage.

We are heading towards a huge switch of how energy is produced with fossil fuels being replaced by renewable energy sources. It is not difficult to replace the energy you use in the house and there is no need for futuristic technology. There are already many established products on the market such as high efficiency vacuum solar collectors, heat pumps & small wind power stations that can supply the energy being used in a house. The company Sol & Energiteknik SE AB in Huskvarna has many different products which can reduce the need for an outside energy distributor. An average house in Sweden uses 15 000 kWh for heating, 5000 kWh for tap water and 5000 kWh for electricity.

The 1990s were one of the most profitable periods for European airline companies, mainly because of development of world economy and increasing globalisation trends. However, towards the end of the decade, a global economic downturn, high oil prices and new forms of competition turned the industry towards troubled times. The European air-travel industry had to face and accept the new airline business concept, called low-cost or no-frill airlines. In these conditions, traditional airlines had to rethink their strategies and question the old business model. As a response to the competition, European traditional full-service airlines formed alliances or networks to expand the route network and to increase efficiency.

In a business environment where the stakeholder perspective is evolving and sustainable development is receiving increased attention, it is of importance for companies to adjust. The demand and pressure is exerted from several stakeholders who force companies to take action and live up to the expectations because if failing to do so, negative consequences will most likely be the case. The attention of this study is on ABB Power Products (ABB PP) and their environment and working environment risk management. The aim of this thesis is to identify and describe how perceived environmental risks are managed and what the incentives are to work proactively to minimize the risks. The incentives for a proactive risk management strategy are researched through both a strategic and operational perspective.

A study was carried in conjunction with the Orthodontic department at Halmstad General Hospital in Sweden to investigate the possibility of reducing cost and manufacture time of dental implant drill guides. The current system involves sending a digital image in STL format to the Materialise factory in Belgium where information of the position of dental implants is translated onto a moulded mouthpiece. Drill guides are placed in the mouth piece which is then returned to the surgeon. The mouthpiece complete with drill guides is then placed in the patients mouth and used as a guide for the implant drill holes. The cost of 10000 sek and a turnaround time of 2 weeks gave rise to the need for a faster and cheaper solution.

Idag är intresset för högpresterande betong (HPB) växande runt om världen då fördelarna är många, eftersom slankare, tätare, starkare och lättare konstruktioner kan tillverkas. Detta examensarbete handlar om materialförsök och modellering för en typ av HPB som ska användas i husbyggnation. Arbetet inleddes med materialförsök i färskt tillstånd, där god gjutbarhet och konsistens eftersträvades. Utgångspunkten var från ett grundrecept med två olika ballastsorter (slaggballast med flygaska och krossballast från asfaltindustrin med silikastoft), vilka namngavs till pilotförsök 1 och pilotförsök 2. Vidare valdes pilotförsök 1 att provas i hårdnat tillstånd då det visades att det var mer ekonomiskt lönsam eftersom ballasten inte behövde siktas, lägre vct tillhandhölls och att flygaskan som användes i pilotförsök 1 är billigare än silikastoft som användes i pilotförsök 2. Resultaten efter 28 dygn för de materialförsök som utfördes i hårdnat tillstånd var:Tryckhållfasthet; 141,9 MPaDraghållfasthet; 7,0 MPaBöjdraghållfasthet; 10,0 MPaElasticitetsmodul; 46,4 GPaKrympning efter 56 dygn; 0,5 ?Samtliga försök utfördes enligt svenska standarder (SS). Dessutom vidareutvecklas och förbättrades ett redan arkitektoniskt gestaltat Attefallshus ur ett konstruktions- och hållbarhets perspektiv, där fokus låg på transport- och produktionsförutsättningar.

The society of today is dependent of secure transports and deliveries of electrical power. Interruptions in different activities because of fallen trees cost a great deal of money in form of reparations and claimed damages for transport companies and electrical suppliers. Fallen trees along some railway sections are a severe problem. For instance, to repair the damages of the storm of week 5 year 2002, costed 2 800 000 SEK for the line region of Hässleholm. Today, the Banverket railroad company has no norms in general for how close to the railway the forest is allowed to grow.

Introduction/Background: Economic evaluations help decision-makers to make informed decisions regarding resource allocation. Information generated from CEA can support evaluations of a new intervention with current praxis. The evaluations also provide information as to whether an intervention is cost-effective, both in economic terms and in health gains. Objective: The aim of this thesis is to investigate the use of economic evaluations in public health, with a focus on CEA. Use of economic evaluations is regarded as both a method for evaluation and as support for informed decisions.

The purpose of this work was to see if it was possible to rebuild an old dairy house into a house fore sheep production. The goals fore the work was to see witch kind of production model was suitable, how the actual drawing would look like and witch kind of interior was needed. The building was built in the beginning of 1900. It is located on the mountain Kinnekulle in Sweden. It was a big production fore its time and hade about 60 dairy cows. It was a lot of hard work because the floor was built by big stone blocks and it was very hard to rebuild when some more automatic solutions came fore handling all the manure. The idea of remaking the building came when we rebuilt the roof fore 5 years ago.

Accounting for financial instruments can either be based on a transactions approach or an eco-nomic approach. Under a transactions approach instruments are reported at cost whereas under an economic approach instruments are reported at fair value. Hence, under a transactions approach realization becomes a criterion for recognizing fair value fluctuations as revenue whereas under an economic approach it does not. A mixed model is defined as a combination of the transactions approach and the economic approach insofar it records some accounting items at cost and other items at fair value. The mixed model gives rise to an issue commonly referred to as an accounting mismatch.

Higher demands of competitiveness and efficiency have led to increasing sizes of farms, with more land, more capital and more comprehensive logistics. The aim is to gain benefits of scale economies that reduce the production cost per unit. However, a greater extent of the business exposes the farm of increased risk where small deviations rapidly can erase the benefits. A modern dairy farm thus put high demands on the farmer?s ability to coordinate, plan and manage the forage production through the whole process until storage to obtain silage of the desired quality and quantity at the right price. The objective of this study was to design a simple model, i.e.

This thesis gives suggestions as to how to design a wooden-based wave-power buoy. The thesiswas carried out at Uppsala University in collaboration with the Division of Electricity and AppliedMechanical Engineering. The product was conceived and developed taking into consideration anumber of requirements put forward by the supervisor, Magnus Rahm. The most importantdemands were that the material used should be able to withstand pressure from the sea withoutbeing damaged and that the production costs should be low.Department of Engineering Sciences, Division of Electricity at Uppsala University was visitedseveral times to discuss issues including the various ideas with the supervisor Magnus Rahm, andwith several people in the department.The work started by studying available literature in order to get background information aboutsuitable methods available for the project and to see how similar projects were carried out. Thereason for this was to get a better understanding of this particular problem and how to solve it.After consulting the supervisor, the group decided to construct four different buoys using fourdifferent materials.

This thesis gives suggestions as to how to design a wooden-based wave-power buoy. The thesiswas carried out at Uppsala University in collaboration with the Division of Electricity and AppliedMechanical Engineering. The product was conceived and developed taking into consideration anumber of requirements put forward by the supervisor, Magnus Rahm. The most importantdemands were that the material used should be able to withstand pressure from the sea withoutbeing damaged and that the production costs should be low.Department of Engineering Sciences, Division of Electricity at Uppsala University was visitedseveral times to discuss issues including the various ideas with the supervisor Magnus Rahm, andwith several people in the department.The work started by studying available literature in order to get background information aboutsuitable methods available for the project and to see how similar projects were carried out. Thereason for this was to get a better understanding of this particular problem and how to solve it.After consulting the supervisor, the group decided to construct four different buoys using fourdifferent materials.

Performance of an intersection affects the total travel time in a traffic network. An intersection with good performance can easily be described by its contribution to lower travel time than in a comparable intersection. The travel time is of importance in the cost calculations when a specific intersection is to be chosen and designed. It is important to be able to make correct and precise performance calculations so that the cost calculations will not be incorrect. For that purpose the software Capcal, which is a traffic model for intersection analysis on performance, is used in Sweden.

The financial crisis in 2008, effected companies around the globe and forced them to change their operational strategies, in order to survive. Companies with international links needed to consider external effects and due to that adapt their strategies on a global level. Demands for goods and service were decreasing and companies could only manage the cost during a recession to not face bankruptcy. Organisations need to reconsider their optimal strategy as this will determine their future outcome when managing a crisis as the one in 2008. British Airways - Air Cargo is a global company with an international network which serves about 80 countries, with about 200 destinations.