The study was conducted with an landscape approach with an subject related approach in the field of environmental psychology to investigate how road design affects drivers' choice of speed. The purpose was to portray road environments on thoroughfares in urban areas to motivate motorists to keep the speed limit and thus increase road safety for vulnerable road users. The task question was formulated, how can thoroughfares in suburban settings be portrayed to motivate motorists to reduce speed? The study was conducted throughout a literature review of motivational speed measures along with interviews with road design experts at the Swedish Transport Administration. Case studies were conducted on three thoroughfares in the Stockholm suburbs Vallentuna, Upplands Väsby and Danderyd.

The number of data centers and their capacity is increasing throughout the world. Theenergy used in these data centers and the emissions from the use are increasing at thesame rate. The total use of energy will double from 2008 to 2011 based on the trends indata centers use. Research in this area says that the emissions from data centers willhave surpassed the level of airline traffic in 2020. The index used today to compare howefficient a data center is, called PUE, is lacking some information.

Background: It has been shown that EDI can yield positive effects within companies. Which effects are possible for a company to direct assign to the introduction of EDI and is it possible to estimate the total effect.Purpose: The purpose of this study is to estimate and analyze the effects of using EDI in electronic business. We also want to contribute with a model for measure and estimate the effects of EDI.Accomplishment: We have studied literature concering EDI and realized a preliminary studie in form of interviews with experts to establish deeper knowledge of EDI. We have also tried to estimate the effects obtained in companies in three different businesses, power, government and transport industry.Result: To obtain as good effects as possible it is important that the co- oporation is built on trust and engagement. Before implementing the EDI-system a thorough overhaul of the processes in the company should be done, involving both the top managers and the staff.

Örebro svets & hydraulik AB tillverkar lastknektar till Suzuki Garphyttan. På lastknektarna transporteras sedan stora rullar av tråd i stål. Knektarna har visat sig kollapsa efter viss tids användning och behöver därför en förbättrad konstruktion. Höga laster, tuff hantering samt ovarsamma lyft kan vara orsaker till att knektarna kollapsar. Örebro svets är väl införstådda var skadorna uppstår i nuvarande konstruktion och vill därför förstärka denna del och konstruktionen i sin helhet.Kraven på den nya konstruktionen, förutom att vara mer hållbar, är att befintligt mått mellan benen ska följas och att knekten ska vara staplingsbar vid transport till galvanisering.Nuvarande knektar har modellerats i CAD-programmet Pro/ENGINEER för att sedan analyseras med Finita Elementmetoden i beräkningsprogrammet ANSYS för att visa var deformation och spänningar uppstår.

Volvo Human Monitoring (VHM) is an ongoing project at Volvo Cars where they measure, amongst other parameters, inhalation and exhalation through a device called Respiratory Inductance Plethysmograph (RIP), on drivers. RIP measures changes in the cross-sectional area of the chest and abdomen. When the driver is in motion, such as when she is turning the vehicle, the cross-sectional area changes and noise in the RIP signal may arise.The noise results in a large number of manual adjustments in the analysis of the RIP signal, which is very time consuming and the validity of the device for measuring inhalation and exhalation is questioned.The purpose of this study was to improve the efficiency of the analysis of the RIP signal. The goal was to create a new data processing tool in Matlab that automatically detects inhalation and exhalation from a RIP signal with higher validity compared to the previous data processing tool.In this study, nine tests were performed on drivers while they were driving in different scenarios such as highway, country road and in city traffic. Inhalation and exhalation was measured using a RIP, a pneumotachograph with a tightly sealed facemask and a thermocouple placed between the nose and mouth, which was used as reference to the RIP.The result of this study was a data processing tool that automatically detects inhalation and exhalation with higher validity compared to the previous data processing tool.

In most countries, the dairy industry focuses on the volume of milk produced instead of its composition. This results in a high content of water and a lower proportion of fat and protein. A high proportion of water is not desirable when processing the milk into various dairy products like cheese, cream and milk powder. High water content also increases the costs for transport and storage, and also an unnecessary, albeit marginal, strains on the world?s water reservoir.

Örebro svets & hydraulik AB tillverkar lastknektar till Suzuki Garphyttan. På lastknektarna transporteras sedan stora rullar av tråd i stål. Knektarna har visat sig kollapsa efter viss tids användning och behöver därför en förbättrad konstruktion. Höga laster, tuff hantering samt ovarsamma lyft kan vara orsaker till att knektarna kollapsar. Örebro svets är väl införstådda var skadorna uppstår i nuvarande konstruktion och vill därför förstärka denna del och konstruktionen i sin helhet.Kraven på den nya konstruktionen, förutom att vara mer hållbar, är att befintligt mått mellan benen ska följas och att knekten ska vara staplingsbar vid transport till galvanisering.Nuvarande knektar har modellerats i CAD-programmet Pro/ENGINEER för att sedan analyseras med Finita Elementmetoden i beräkningsprogrammet ANSYS för att visa var deformation och spänningar uppstår.

In this master thesis work, a new method called MultiScat, is compared with the conventional method with alfa-correction, for computing concentrations from intensities in X-ray spectrometric analysis. The conventional model is a linear model, which only takes the photoelectric effect into consideration. It doesn't consider Rayleigh and Compton scattering even though it has a great impact on the measured intensities. Here MultiScat differs a lot. MultiScat is based on a solution of the Boltzmann transport equation.

With the climate change issues growing in importance on the social agenda, the field of urban masterplanning is of no exception when it comes to minimizing the carbon footprint in a variety of projects. The aim of this thesis has been to prepare the Carbon Critical Masterplanning tool, a software plugin for carbon dioxide emissions assessment developed by Atkins, to be used in Swedish conditions. The main targets were to improve the areas of the tool associated with energy conversion and renewable energy sources, and to test the tool in a real case. A planned construction of a new campus in Albano, Stockholm was chosen for the pilot study. A 3D model was built in the tool and the carbon footprint was calculated for a variety of combinations for energy supply to the future area.

This project is about Jönsaplan in Landskrona. Jönsaplan is situated at the center of Landskrona in a part called Södra centrum which the municipality is developing, mainly by building new residential buildings. Today, Jönsaplan is not a functioning square. This is due to a ferry terminal and its many fences that block the way for people. In this project, I have assumed that the ferry terminal will be moved somewhere else so that Jönsaplan can be a real square. By studying The Concise Townscape by Gordon Cullen and Byens uttrykksformer by Thomas Thiis - Evensen and three reference places, Daniaparken, Raoul Wallenbergs torg and Norr Mälarstrand, I came up with a number of guidelines for my design proposal for Jönsaplan.

Stora som små företag kan idag vara med och konkurrera om kunder på den globala marknaden. För att överbrygga den geografiska problematiken med stora avstånd mellan kunder och aktörer inom värdekedjan, har dagens utvecklade transporter och tillika transportnät haft en enorm betydelse. Produkter kan idag med relativt små ekonomiska medel förflyttas för att skapa ett större ekonomiskt värde på ett långt avstånd ifrån det säljande företaget.Olika produkter har dock olika krav beträffande leveransservice och leveranssäkerhet. Många produkter kan transporteras och distribueras under en längre tid och för en lägre kostnad, medan andra kräver att transport och förflyttning löses omedelbart. De långa avstånden på den globala marknaden gör det extra svårt för företag vilka säljer och distribuerar tidskänsliga produkter, men även för exempelvis produkter utvecklade för akut vårdassistans.

Wildlife fences are today commonly used along highways to reduce the risk of vehicle collisions with wildlife. Since traffic and roads have expanded over the years, wildlife behaviour has become more interesting not only for the prevention of vehicle collisions but also to understand how human activities impact their natural habitats. Moose is one of those animals that have increased in interest in such studies. In this study, I tested if the probability to cross wildlife fences of moose would increase with increasing home range sizes, and also at what time of the year they cross. The study area is situated in Nordmaling municipality, located in Northern Sweden in the County of Västerbotten.

With the climate change issues growing in importance on the social agenda, the field of urban masterplanning is of no exception when it comes to minimizing the carbon footprint in a variety of projects. The aim of this thesis has been to prepare the Carbon Critical Masterplanning tool, a software plugin for carbon dioxide emissions assessment developed by Atkins, to be used in Swedish conditions. The main targets were to improve the areas of the tool associated with energy conversion and renewable energy sources, and to test the tool in a real case. A planned construction of a new campus in Albano, Stockholm was chosen for the pilot study. A 3D model was built in the tool and the carbon footprint was calculated for a variety of combinations for energy supply to the future area. The results show that use of locally installed renewable energy sources can reduce the total climate impact when life cycle perspective is applied.

The determination of the optical properties of biological tissue is an important issue in laser medicine. The optical properties define the tissue´s absorption and scattering behaviour, and can be expressed by quantities such as the albedo, the optical thickness and the anisotropy coefficient. During this project, a measurement system for the determination of the optical properties was built up. The system consists of a double integrating sphere set-up to perform the necessary reflection and transmission measurements, and a computer algorithm to calculate the optical properties from the measured data. This algorithm is called Inverse Adding Doubling method, and is based on a one-dimensional transport model.

This thesis is closely related to the Dynamically Self-Configuring Automotive System(DySCAS) project. DySCAS is a middleware for electronics in an automotive system. Thethesis work has been performed in cooperation with ENEA. Parts of the demonstrationplatform Self configurable High Availability and Policy based platform for Embeddedsystem (SHAPE) developed for the DySCAS project by ENEA have been used in theimplementation phase of this master thesis.The goal of this thesis was to evaluate how the Meteor MW, an offspring of the DySCASmiddleware, should handle QoS and to design a Quality of Service Manager (QoSM) for theMeteor MW that fulfilled hard real-time requirements. The thesis also had the objectiveof analysing and identifying the requirements on such a QoSM from a QoS perspective.Specifically the requirements to guarantee real-time support for applications running onthe MW.