Huvuduppgiften i detta examensarbete har varit att programmera en Android smart-telefon så att den kan kommunicera med en bio-sensor med syfte att skapa automatiska larm vid till exempel hjärtproblem. Hur lösningen har vuxit fram har dokumenterats tillsammans med resultatet av den informationssökning som utförts parallellt inom angränsande ämnesområden.Vid programmeringen har en Service använts för att upprätthålla en prioriterad kommunikationsprocess mellan bio-sensor och telefon. Programprototypen använder även en Widget ? en mini applikation på skrivbordet - som är ett snyggt sätt att presentera mätdata.När denna produkt börjar säljas på marknaden kommer den vara klassificerad som en medicinteknisk produkt. Detta innebär att det finns ett speciellt regelverk för leverantören av produkten att följa.Applikationen är enkel att hantera för användarna men det innebär inte att den alltid är lämplig för alla.

To get the maximal output of your exercise in gym machines, there are different factorsto be considered. For example the strength of the muscle varies dependent on the positionof the muscles. To get the best results of the exercise the load has to reduce and increaseat specific positions.This study was made in cooperation with Caretaker Scandinavia AB, a company forsales, marketing and development in health care. They are general agent for Nordic Gymwho works with manufacturing of equipment and machines for gym and fitness.The aim of this study was to generate a method of measurement to evaluate and controlthe biomechanics of Nordic Gym´s workout equipment. A protocol for an ergonomicanalysis on the equipment has also been elaborated.One of the methods to measure the biomechanics was to measure the torque through thewhole movement.

Tractors of today come equipped with a CAN-system. A CAN-system sends information from sensors to electronic control units who process the signals. The sensors measure several interesting parameters such as force, pressure and speed for various components of the tractor. This thesis discuss a force sensor which is placed in the pivot of the tractors three point linkage, the sensor measure the horizontal reaction force from the load that the tractor is exposed to. Signals from this sensor can be used to measure the force from any implement that the tractor is exposed to during an operation.

The aim of this study is to increase knowledge and understanding of free play or free fun time importance for children of age around five years in preschool, in order to promote children?s development and learning. The focus was on exploring and better understanding of teacher?s and educators? approach to the free fun play time as a tool in their educational work, and also about their own role in this context as well as analyzing of forms, rules and structures spontaneously created by groups of children having free play fun time. Another important moment of this study was to give more light on approaches to this issue in education theories by Piaget, Vygotsky and Freud among others.As to the practical experimental part of the study it has been performed at a preschool and kindergarten in a suburb at the outskirts of Stockholm, with four employed educators there and with groups of children of age around five.

AbstractThis work was assigned by a technological company that manufactures gas detectors in which the sensor signal is processed using digital filters. These filters have been developed by a consultancy firm which converted previously used analog filters to digital filters. The purpose of this work has been to analyse inadequate, and sometimes erroneous, documentation from the project in order to provide the company with know-how and tools for further improvement of their products. The work has been done using the simulation software COMSOL which was bought solely for the project. Analysis showed serious flaws as well as pure errors in the consultant?s documentation.

This paper describes the work done trying to diminish the noise present in the signal from an IR-detector. The project was aiming towards two different kinds of applications; heat protection and presence detection. The hypothesis was that the signal-noise ratio would decrease if a filter and a proper installation were used for the detector. Some experiments were executed to determine what kind of filter were the most suitable for each application and how these could be installed. After executing the experiments and evaluate the results we recommend to use a specific filter for each application.

Abstract   In this thesis, my aim was to investigate how preschool teachers view their involvement in children's free play. In order to answer this, I chose to do semi-structured interviews with four preschool teachers in three different preschools. My interviews has revealed similarities and support for as how history of research looks at the involvement of educationists. Both research and my results stresses the importance of being active in children's free play and to be a supportive teacher, particulary in conflict situations. For those children who have difficulty entering into the free game its the educationists task to co-play and help the children find the game.

Denna rapport behandlar utveckling av en tvåhjulig balanserande robot. En PID-regulator är implementerad i en mikrokontroller, som även AD-omvandlar en sensorsignal, samt styr motorer via H-bryggor med pulsbreddsmodulering. I rapporten förklaras framtagning av diskret PID-regulator, processorkort, motorkort, val av komponenter och sensor för att mäta robotens vinkel mot ett vertikalplan.Roboten kan balansera stillastående, men behöver kompletteras ytterligare med hjulåterkoppling för att kunna balansera medan den kör. Roboten balanserar med mätdata från en mekanisk golvavkännare (potentiometer). Andra sorters sensorer diskuteras också, t ex accelerometer, gyro och optisk sensor..

This is a final thesis done at BT, considering one of their forklift truck models called Reflex. The first part of this report is about a preliminary investigation investigating what kind of diagnostic systems BTwants to use, and also which demands there are to meet all expectations on such system. Secondly a diagnostic system, which will show if the drive wheel is worn out, will be presented. In the preliminary investigation, two kinds of diagnostic systems were mentioned. These were Model based diagnosis and Predictive analysis.

Bilsäkerhet är en viktig fråga i dagens samhälle. Det enklaste sättet att skydda sig vid en bilfärd är genom att använda säkerhetsbälte. En säkerhetsbältesrulle är uppbyggd av flera olika komponenter, en av dessa kallas torque tube som tar energi när kroppen fångas upp av bältet vid en eventuell kollison. Säkerhetsbältet ska skydda passagerarna i bilen i många år och vid olika temperaturer. Torque tuben är i detta fall gjuten i en zinklegering som heter Zamak5 som förändrar sina materialegenskaper i åldrat och kylt tillstånd.

This master thesis is a study of anaerobic thread lockers and is done in cooperation withÖhlins Racing AB, which is a Swedish manufacturer of vehicle suspensions.The suspension in vehicles is constantly exposed to high vibration levels and a suspensionunit has several screw- and cylindrical joints. As an extra safety precaution so that thecomponents in the suspension doesn?t fall apart when using the vehicle, an anaerobicthreadlocker is added in these joints. The handling of these threadlockers is not totallyharmless and could lead to allergic reactions, and therefore there are Swedish laws to limit theuse of these. However, new types of anaerobic threadlockers have recently been launched onthe marked that are not considered under this law.

A one-cylinder research engine has been used for studies with a Diesel Dual Fuel concept (DDF). DDF is a concept that utilizes a pilot diesel injection to ignite a homogenous natural gas/air mixture. Emissions and engine efficiency have been analyzed in an emission cycle called European Stationary Cycle (ESC) and the knock/pre-ignition problems with this type of engine have been investigated.At low and mid torque levels, an early diesel injection around 60 crank angles degrees (CAD) before top dead center (TDC) was used. At these loads raw NOxemissions was below EURO 6 level (0.2 g/kWh). NOxwas at EURO 5 level over the complete ESC without after treatment and with SCR at high loads it should be possible to reach EURO 6.One issue with DDF is the high HC emission levels.

This report contains a degree project made by the mechanical engineering students Lennart Andersson and Daniel Jansson. The project has performed in assignment by SOMAS Valves AB in Säffle. SOMAS are leading in development on control and on/off valves. To maintain this position they always want to improve their products. One way in this development is valves that are more tightened.The purpose with our project was to investigate another seat design on a HiCo (High Cobalt Alloy) seat to a SKV 150 PN 25 valve and compare this to an original HiCo seat.By modifying the seat on a ball valve we want to achieve a valve that leaks lesser then a valve whit original seat.

This degree project was conducted in collaboration with Gremo AB located in Ätran.The aim of the project was to develop a solution to secure quality and to help assemblingthe locknut holding the vertical hinge on the harvesters and foresters from Gremo.At this time the nut is assembled manually by the aid of an overhead crane. The nut istightened differently from time to time, and there was no specified torque to which it istightened. Another present problem was the locking washer which sometimes getsdamaged during assembly, when this happens the procedure has to be started over fromthe beginning. The current assembly procedure is very time consuming and lengthy forthe employees.Our task was to design a machine that could tighten the nut to a specified torque with amargin of error of ± 3%. The assembly procedure will be held simple and the timerequired at a minimum.The project started by developing several principle solutions, the one solution that bestmatched our specifications were developed to a primary solution.Today we have started manufacturing and assembling our prototype.

This rapport is result of a project. The purpose of which was to design a circuit that is used in a heat glove. The heat glove is the technical aid which provides heat inside a glove.It is specially suited for old people who have problems with cold hands because of decreased blood circulation.There already was an old circuit in the glove that gives a constant current which develops heat from battery to glove through a circuit. The temperature is between 32 and 34 degrees.The problem with the existing circuit was to regulate the temperature. There is only on/off switch and there is no way to adjust desirable value of the temperature.In order to solve the problem the old circuit was investigated.