The acoustics in a control room is a complicated phenomenon. Early reflections, reverberation time and area in the room are some of the problems. This report is about the reflection on the mixing console in a control room. The control room being built, these reflections are difficult to take into consideration since the mixing console is one of the very last items you place in the room. This report will explain three main measurements that were done in order to get the answer to the following question: Does the mixing console interfere the frequency curve at listening position? Three measurements were done and the difference between the measurements was that the microphone and the loudspeakers were placed in different places in the control room.

The study examines selectivity of the customer base and scarcity of a product?s effect on attitude and value towards a product or service. A questionnaire study is made from three different situations. The result varied depending on the situation; however it was found that selectivity of the customer base and scarcity has a great impact on the attitude and the perceived value towards a product or service. Selectivity of the customer base was found having the highest level of impact on both attitude and perceived value.

A clean and affordable energy source for cooking is deficient in developing countries. People rely on fuels that contribute to environmental, social and health problems.Biogas is an alternative energy source and an increased investment in small-scale biogas production can in several developing countries be found. Several projects have started to use the technology in developing countries because of the benefits with biogas. Some cases in the establishment of biogas plants have succeeded and some have not. The study is a literature review supplemented by two field studies.

Future emission legislation puts great emphasis on increasing the efficiency of the engine, thereby reducing fuel consumption. The tribological contact between cylinder liner and piston ring is where an great amount of energy is lost due to friction, and by reducing these losses an reduction in fuel consumption can be achieved.The aim of this thesis was to evaluate the tested piston ring coatings against a plasma sprayed cylinder liner and rank these combinations of materials for friction and wear resistance. The coatings that were tested was Cr + Al2O3, (Al,Cr)N, two types of CrN and WC / C.The experimental tests were performed with a so-called pin-plate, where used oil with addition of an acidic mixture of sulfuric and nitric acid to mimic the acidic condensate formed when exhausts recirculate, were added with a continuous flow. The results were then analyzed by weighing, studies by optical microscopy and scanning electron microscopy (SEM) and profile measurements.The results from each material combination were that the plasma coated cylinder liner wears too aggressively in order to yield a ranking of the piston ring coatings based on the parameters of friction and wear resistance. It is therefore proposed that an alternative coating on the cylinder liner should be developed, lacking the large abrasive wear on piston rings and that can withstand the corrosive environment resulting in engines equipped with EGR.

Abstract 1.The purpose of this study was to investigate the effects whole body vibrations on maximal strength, power output and neuromuscular activity in m. pectoralis major during bench press.Participants consisted of 35 male and 9 female military high school students (m=23, 1 years). On the basis of initial maximal performances in bench press the participants was divided into two experiments groups and one control group. Intervention groups performed a specifically designed push up program on a vibrating plate respectively a step board during 12 weeks Initial load at 60 % of 1 RM showed an average of 46, 5 kg. All groups showed an average increase of 13 kg for each person after 12 weeks.

Enköping?s Rugby Club has long lacked a bigger hall to gather their members in, where they can meet and socializes outside trainings and games. Thanks to Enköping?s municipality, The Swedish Inheritance Fund, Swedish Sports Confederation, sponsors and club members the clubhouse will be built out with additional 100 square meters.The project is planned in two phases of which phase one is the buildup of the new clubhouse and phase two is the renovation of the existing part. Phase one started with the first groundbreaking in December 2006 and was finished for the season 2007.

När en konstruktion byggs på det viset att dess bottenplatta hamnar under grundvattenytan, skapas ett grundvattentryck upp mot bottenplattan och konstruktionen, som kan åstadkomma stora problem. Grundvattnet, som tryckts undan av konstruktionen, vill nå upp till sin ursprungliga nivå och därmed trycka med sig konstruktionen upp. Detta fenomen kallas hydraulisk bottenupptryckning. Fenomenet kan motverkas på olika sätt, där rapporten beaktar två olika sätt att motverka hydraulisk bottenupptryckning på: genom en bottenplatta som är tyngre än grundvattentrycket eller förankra bottenplattan mot ett fast underlag.Genom att uppmärksamma och sammanställa projekt (huvudsakligen konstruerade av Tyréns) som tagit hänsyn till ovan nämnda fenomen vid dimensioneringen av bottenplattan, har en rapport skapats. Denna rapport ska finnas för att åstadkomma kunskapsåterföring av de problem som uppstått i projekten och deras lösningar.Utöver att skapa en rapport där de berörda projekten sammanställs ska en bottenplatta optimeras, huvudsakligen med hänseende till bottenplattans tjocklek och dess bärförmåga mot genomstansning för olika förankringstyper.

Earlier investigations showed that damages on timber from feeding rolls could be within the lower classes of damage according to VMRs classes. Knowledge about differences in productivity between kind types and aggressive types of feeding rolls is necessary because it should influence the question about damages on timber caused by different feeding rolls. In this study the production and timber damage in a harvesting head were evaluated at three levels of pressure (8, 10 and 14 MPa) on the feeding rolls, and with three different types of rolls. One type, the rubber cushioned steel plate roller had 10 mm studs and rubber damping, one ?middle? type made of solid steel with 14 mm studs, and one aggressive type, also made of solid steel with 18 mm studs.

Future emission legislation puts great emphasis on increasing the efficiency of the engine, thereby reducing fuel consumption. The tribological contact between cylinder liner and piston ring is where an great amount of energy is lost due to friction, and by reducing these losses an reduction in fuel consumption can be achieved.The aim of this thesis was to evaluate the tested piston ring coatings against a plasma sprayed cylinder liner and rank these combinations of materials for friction and wear resistance. The coatings that were tested was Cr + Al2O3, (Al,Cr)N, two types of CrN and WC / C.The experimental tests were performed with a so-called pin-plate, where used oil with addition of an acidic mixture of sulfuric and nitric acid to mimic the acidic condensate formed when exhausts recirculate, were added with a continuous flow. The results were then analyzed by weighing, studies by optical microscopy and scanning electron microscopy (SEM) and profile measurements.The results from each material combination were that the plasma coated cylinder liner wears too aggressively in order to yield a ranking of the piston ring coatings based on the parameters of friction and wear resistance. It is therefore proposed that an alternative coating on the cylinder liner should be developed, lacking the large abrasive wear on piston rings and that can withstand the corrosive environment resulting in engines equipped with EGR.

This study discloses home-care organizations in one municipality in Sweden and five units work with implementing the social services legislated value base for elderly people. The aim of this study is to gain an understanding of personnel and managers perception of the value base and its implementation in the practical work with the elderly. A qualitative method has been used to analyze the questions raised by the aim of this study. The empirical data was retrieved by semi-structured interviews with managers and their personnel in homecare service The empirical data was analyzed on the basis of the neo-institutional theory, Michael Lipsky?s theory concerning street-level bureaucrats and previous research regarding implementation of social policy and the practical home-care work.

När en konstruktion byggs på det viset att dess bottenplatta hamnar under grundvattenytan, skapas ett grundvattentryck upp mot bottenplattan och konstruktionen, som kan åstadkomma stora problem. Grundvattnet, som tryckts undan av konstruktionen, vill nå upp till sin ursprungliga nivå och därmed trycka med sig konstruktionen upp. Detta fenomen kallas hydraulisk bottenupptryckning. Fenomenet kan motverkas på olika sätt, där rapporten beaktar två olika sätt att motverka hydraulisk bottenupptryckning på: genom en bottenplatta som är tyngre än grundvattentrycket eller förankra bottenplattan mot ett fast underlag.Genom att uppmärksamma och sammanställa projekt (huvudsakligen konstruerade av Tyréns) som tagit hänsyn till ovan nämnda fenomen vid dimensioneringen av bottenplattan, har en rapport skapats. Denna rapport ska finnas för att åstadkomma kunskapsåterföring av de problem som uppstått i projekten och deras lösningar.Utöver att skapa en rapport där de berörda projekten sammanställs ska en bottenplatta optimeras, huvudsakligen med hänseende till bottenplattans tjocklek och dess bärförmåga mot genomstansning för olika förankringstyper.

Koagulas-negativa stafylokocker (KNS) klassas som en viktig del av hudens normalflora. Vid skador på hudens barriär som en inläggning av centrala venkatetrar (CVK) innebär kan dock KNS få tillträde till normalt sterila lokaler där de kan orsaka infektion. Vid utodling av borttagna CVK från patienter resistensbestäms bara några enstaka kolonier vilket gör det lätt att missa förekomst av flera olika stafylokock-kloner. Syftet med studien var att undersöka hur ofta en eller flera olika KNS-kloner förekommer på CVK från patienter, samt om det förekommer gemensamma kloner av KNS på CVK från olika patienter. Kolonier från CVK prov analyserades med den biokemiska fingerprintingmetoden Phene Plate-system (PhP).

The objective of this study was to assess validity and reliability for five different owner-completed instruments evaluated to assess chronic musculoskeletal pain in cats. All of the instruments were questionnaires, three asking about behavioral changes, one about the degree of pain and one about quality of life. One of the instruments was written originally in Swedish, the other four instruments were translated into Swedish before use. Data available were records from 57 cats with no signs of pain and 11 cats with different pain-related diagnoses. The diagnoses were ensured by clinical examination including palpation and manipulation of joints, gait testing on a force-plate and X-ray scans. Instrument 1 was completed by 57 pain-free and 11 pain-affected cats.

Safe retrieval of nutrients from human excreta to fertilize crops in order to gain adequate yields will increase food security and sustainability in agriculture areas with nutrient-poor fields. Safe and nutritious food will meet the dietary needs of the individual which promotes public health and the ability of an active life. Human excreta should be considered as a resource instead of being assumed as waste. Human faeces and urine is excellent fertilizers which may close the nutrient loop if utilized properly. However, sanitation of the excreta is required to prevent disease transmission by reducing the content of gastrointestinal pathogens such as bacteria, viruses and parasites. The objective of this study was to in small scale evaluate the sanitation in a combined liquid compost and urea treatment by monitor the inactivation of bacteria and viruses at the combination three start temperatures, 45, 40 and 35 °C, and three additions of urea, 0.5, 0.75 and 1 % and reference, 0 % urea addition.

The goal of this thesis is to design an attachment between a duct and a pod. A pod is what could be compared to an outboard engine for larger vessels. The pod is placed on the outside of the ship?s hull and can rotate 360 ?. A duct is a large steel ring that can be placed around the propeller on the pod to increasethe propulsion force of the ship in lower velocities.