The wood-living beetle Ceruchus chrysomelinus is a rare species connected to natural forests. In Sweden, it is red-listed as endangered (EN) and an action plan for its preservation has been done by the Swedish Environmental Protection Agency. In this work I have therefore investigated how a translocation of the species succeeded after 17 years. I aimed to study the species dispersal biology, its substrate preferences and the supply of suitable wood on this site. The study was performed during 2012 in Pansaruddens nature reserve close to Uppsala in Sweden, which is a spruce dominated forest.

With the elevated oil prices of today it is necessary to look for other heating alternatives. If the oil price continues to develop in the same way it has done the last years it will soon be impossible for many producing garden companies to survive. The purpose of this diploma work is to compare three different fuel options in order to find the most economic one considering the conditions of Katrinebergs Handelsträdgård AB. In relation to oil it is profitable to change to any of the three alternatives: wood chips, wood pellets and grain. The most profitable option is to change to wood chips. This alternative has a payoff time less than three years and after that the annual saving compared to the oil is relatively high. The annual cost is 65 % of the cost of the oil alternative.

The study was carried out as a time study of five wood chippers placed on trucks,so?called huggbilar. They are trucks with built?in wood chipper, chip bowl and crane pulling a chip trailer. The system is used for chipping wood fuel, transporting, and delivering the chips to heating plants.

The aim of the study was to compare productivity in first thinning of birch stands, when either energy- or pulpwood was harvested. The systems total profitability was also compared by including forwarding and chipping costs. A Gremo 950 HPVR harvester was used and the same driver was used under the entire study. During the pulpwood harvest a Logmax 4000b harvester head was used and a feller buncher head made by Silvatec was used during the energy wood harvest. Six study unit pairs were located in a birch dominated stand outside Ängelholm in Skåne.

The primary purpose of this study has been to investigate the Swedish timber industry?s perception of compression wood. A secondary aim has been to describe particular areas within the production process where compression wood is likely to cause problems. This study has mainly been carried out as a questionnaire. In order to connect the findings to current research, additional information has also been collected by means of a literature review. The questionnaire has been intended for sawmills and wood-manufacturing companies from various production classes and owner categories, as well as from different parts of the country.

A high amount of dead wood is one of the most important prerequisites for high biodiversity on forest land in Sweden. Dead wood is most abundant in young forests, thinned forests, woodland key habitats and protected forest land. In old-growth forests most of the dead wood consists of logs and snags, whilst in managed forests a huge proportion of dead wood is made up of logging residues like stumps and FWD, fine woody debris (< 10 cm diameter). All these different types of dead wood may serve as substrates for epixylic bryophytes and lichens. However, few studies have been conducted on the relative importance of these different fractions of dead wood for the occurrence of bryophytes and lichens, especially when considering dead wood on thinned forest land.

If you have access to wood, a wood burning boiler is a cheap way to heat your home, but it is certainly not the most convenient option. Wood requires many operations and management, which takes time. One way to reduce this workload is to have a modern boiler with automatic ignition. Enertech/CTC has a desire to create an accessory with automatic ignition to a modern wood burning boiler. Today there is no boiler on the market that can ignite firewood automatically without the introduction of paper and sticks.

The purpose of this thesis is to study whether there is a demand for sawn wood products of large dimensions and planed goods among Wallnäs AB:s customers. The thesis consist of two main parts, one survey among Wallnäs present customers and another one which purpose is to increase Wallnäs customer base. Finally there is a chapter that describes what properties the raw material has to have in order to produce the demanded products. The survey to the present customers was conducted through a questioner. A sample of those who stated an interest for either sawn wood products of large dimensions or planed goods, were later contacted for a telephone interview. To reach out to new customers, relevant companies has been identified through the Swedish Trade Councils data base and through the member list of the Timber Trade Federation.

The Swedish pulp and paper industry meets higher demand for energy efficiencyi mprovements with increasing energy prices and changes in the Swedish renewable energy certificate system. One action of energy efficiency improvement is by using secondary heat, that otherwise would have been treated as waste heat, for use in a system with lower temperature demands. The aim of this Master´s thesis is to identify possible secondary heat sources in a typical Swedish pulp and paper mill and to investigate what economic benefits the secondary heat will provide when being used for pre heating of wood chips to a kraft digester.The Master´s thesis focuses on three secondary heat sources; dry warm air, warm water and moisture saturated warm air located inside the pulp or paper mill. Two types of kraft digesters are simulated within this study, a typical Scandinavian digester and a modern twin vessel steam phase digester.Due to quality aspects and low temperature level drying is the drying technology with dry warm air rejected. Using warm water in direct contact with wood chips increases the quantity of water to the evaporation plant and thus reduced pulp or paper production and is therefore also rejected.

Most of the saw and pulp industries have stored wood nearby their production, the main reason is to have a continuous wood flow to the production. Wet storage of wood is of great importance to keep the wood quality. Without water sprinkling the risk of drying outand decomposition through biological activity increases significantly and will result in a negative effect on future production and quality. One drawback of wet storage of wood is the leaching of chemical substances into the surrounding recipient. The log yard run-off contains phosphorus, nitrogen, phenols and organic substances. These substances can cause problems for the surrounding environment. The main objective of this project is to gain an understanding of the wet storage used by the Swedish wood industry and estimate the environmental consequences that run-off water will have on the recipient.

This essay focuses on crime history and gender. It is a study of female crimes in the beginning of the 19th century in a small parish (Askeryd Socken) in Småland in the south part of Sweden. The method I have used is to study the records of Municipal Court regarding the citizens of the parish of Askeryd. I have then tried to find out whether the female offenders have been treated different than the male offenders, if there is a certain kind of gender-related crimes and in those cases where comparison is possible, I have examined if the females are treated in a lighter way. (?female discount?), or if they were treated as mentally unstable.The essay shows that in this particular parish during the years 1825 to 1830, female offenders were not treated in a lighter manner.

This study investigates three different methods for evaluating MOE,Modulus of Elasticity, in field measurements. The purpose is toinvestigate the possibility to use dynamic measurement methods infield measurements that hitherto (2010) has been performed with staticmethods. The objects of investigation are 20 glulam beams. The firstfield measurement took place in november 2007 and applied a staticmethod based on the standard SS-EN 408. The second measurement,described in this study, took place during summer 2010, and appliedstatic as well as dynamic methods.The MOE of wood is affected by a range different factors.

At SIA TallOil's pellets factory in Latvia wood shavings and saw dust are dried with flue gases from a gas burner. TallOil wants to replace the gas with a biofuel that is available at the pellet plant. The reason for this is the unstable gas market in Europe in combination with the fact that TallOil wants to improve its profile as supplier of renewable bio fuels. In this project the technical and economical possibilities for a fuel conversion to ether bark powder, wood shavings or wood powder have been investigated. These fuels should be burned in one of the following applications: TPS BioSwirl, VTS Multifuel burner or Saxlunds bio fuel combustion plant Due to the fact that the fuel alternatives available are relatively common except for bark powder, the work has mainly been focused on bark powder.

The purpose with this study is to find out how much dead wood we can expect us to find in a Russian reference river and compare with studies from Swedish streams. Dead wood are an important structure for the biodiversity in forest streams, studies have shown that population of trout can increase with up to 300 % when the amount of dead wood are increasing from 0 to 8 ? 16 LWD (Large woody debris)/100 m2. Dead wood are also an important structure for the stream character, formations of dams and pools which are important habitats and reproduction areas for salmon and brown trout. The study where taken place in tributaries to the Russian river Varzuga in the North West part of Russia outside Murmansk. Varzuga has low impact of human activity and is considered to be a reference river to rivers in northern Sweden.

The need of raw material does of course fluctuate but the long term view is an increasing demand due to the growing consumption of sawn timber products, pulp, paper and lately also biomass. This has led to a keener competition for wood. At the same time there is an ongoing structural change of a significant part in the Swedish wood supply market, the private forest owners. In 1992, 22 % of Sweden´s 335 000 private forest owner lived apart from their forest. In 2007 this figure had risen to 36 %.