Ocean Thermal Energy Conversion, OTEC, is a sustainable energy conversion technology that is not yet commercialized. OTEC is a technology that utilizes the temperature difference in oceans between the warm surface water and the cold water at 1 000 m depth to run a Rankine Cycle. This technology can produce electricity and provide synergies like fresh water, air conditioning and aquaculture. A simulation program for three alternative OTEC systems has been created in order to decide which OTEC system is most profitable; closed, open or hybrid system. In this simulation a production cost analysis is performed in order to investigate and decide which one of the three systems that has the lowest production cost. The production cost analysis also analyzes if the profitability is affected by the size of the facility. After these analyzes, the most profitable of the three different OTEC-systems is expanded by an installation of solar collectors in order to see if the thermal efficiency is improved. The result shows that the most profitable system varies with the size of the facility.

In the last few years people have become more and more aware of how humanity is affecting the climate. In the direction of reducing the greenhouse gases is to design engines with higher tensile properties and reduced weight, in order to achieve lower fuel consumption and cleaner fuel incineration in today's truck engines.In order to achieve these requirements it?s necessary to increase the combustion pressure in the engine. This requires higher tensile properties and high thermal conductivity of the engine material. The department of Component Technology at the University of Jönköping in collaboration with Volvo Powertrain AB, Scania CV AB and DAROS Piston Rings AB has been commissioned to develop this material and to find knowledge of material properties used in truck engines and piston rings used for marine applications.The purpose with this work is to analyze the tensile properties of a series of cast iron, cast under different metallurgical conditions.Four different series of cast irons have been analyzed from four points of view, carbon concentration, nodularity, amount inoculation and cooling rate.After the tensile test all specimen data was analyzed in a mathematic calculation program called Matlab 2006a.

In today?s society climate change has grown to one of the largest global issues. To reduce emissions of greenhouse gases, large changes of the energy system are required. An increasingly popular solution is investments in local production of renewable energy resources like wind, solar or geothermal power. The following report examines the possibility for implementing a solar power plant on the new hospital Nya Karolinska Solna. Two different technologies for extraction of solar energy has been studied, solar thermal collectors  to meet the need of heating and solar cells to satisfy the need for electricity linked to operating the hospital building.

When a combined heat and power plant produces heat and power it often faces a deficit of heat load during the summer or other periods of time. This heat is often unnecessarily cooled away or the power production has to be reduced or shut off. If it is possible to store heat from periods with low heat demand to periods with high heat demand one can get many benefits. Among these benefits are: increased power production, decreased operation with partial load, uniformly distributed load.To be able to store heat in situations like this long-term thermal heat storages are needed. In this thesis five different types of stores are presented: rock cavern storage, tank storage, pit water storage, borehole storage and aquifer storage.

Students? performance in school is dependent on the indoor climate. This report studies four schools regarding air quality and thermal environment. A survey was made at the schools as well as measurements of carbon dioxide, dampness, thermal climate and, as an indicator for the furniture?s capability to collect dust, shelf factor and fleece factor.

Transdermal drug delivery, besides painfulinjections with syringes, has long been associatedwith small size particle pharmaceuticals, which candiffuse through the skin. This method of drugadministration has only been applicable on a smallnumber of drugs, where active molecules are smalland delivery time should or can be long.Other drug delivery options are oral administrationand injection with hypodermic needles (ordinaryhospital syringes). In oral administration thestomach and liver tend to dissolve the drug and theeffect becomes more difficult to anticipate, anddrug delivery rates difficult to control. Hypodermicneedles are used as a mean of drug injectiondirectly into the bloodstream. This method ispainful and risks infection due to tissue damageand skin penetration.One way to get a painless non-damaging techniquewith high delivery rate that still can delivery largemolecules is to manufacture an array of microscopichollow needles and equip them with a pumping unitthat delivers the correct amount of drugs.This thesis shows the technique and possibility ofmanufacture micromachined needles using low costtechniques of Ion Track Technology (radiation ofheavy ions creates porous materials), electrolessdeposition (non-current activated wet chemistrymethod of depositing metal) and electroplating.

This report is the written documentation of a project work carried out at the Division of Engineering Materials at Luleå University of Technology in cooperation with Seco Tools AB. The project deals with the analysis of residual stresses in Ti-Al-N thin film grown on WC/Co cutting inserts. The composition of Al varied from 0% up to 75%. Increasing the Al content in the Ti(1-x)Alx N compound improves the compressive residual stresses even after annealing of the material. The experiments have been performed in a high temperature x-ray diffractometer (HTXRD) where the interplanar atomic spacing was determined in-situ and subsequent converted into stresses.

The purpose of the study is to investigate the possible effects of an unstable ventilation system and its influence on energy use and thermal comfort. The report also explores how qualified personal working with HVAC view and handles system control.In order to meet the requirements in energy efficiency and a comfortable indoor climate control regulation is a prerequisite. With optimized increased complexity of the climate systems, it becomes more challenging to control the system and the risk of unstable control increases. No previous studies about what affect an unstable system can have on energy use and thermal comfort have been found.The report is based on several tests were the controlling variable has been increased until the system becomes unstable. Two different types of unstable systems have been investigated.

In this thesis proposals for different designs of a borehole thermal energy storage (BTES) have been developed for the building DN-huset in Stockholm, Sweden. To build a BTES results in savings in energy costs by approximately 44 %, i.e. 2 million Swedish crowns annually. Furthermore, a BTES would reduce the annual environmental impact with roughly 75-157 tonnes of CO2 equivalents per year, depending on how the electricity consumption?s environmental impact is estimated.

This thesis work was made to optimize the writing of the construction specificationsat FKA. These construction specifications are created before each plant modificationsthat is started because requirements from the Swedish radiation safety authority(SSM) and internally on Forsmarks nuclear group as constructions / implementationdocumentationThe study was done through seven interviews of two people at three different groupsinvolved in the construction specification and an interview from the group accreditedverification. The four selected groups were selected through an extensive analyticalwork resulted in an elimination matrix where these four groups was considered to bemost involved with the construction specification.The questions asked to these individuals were based on the instructions and sampletext that are described in the construction specification. To ensure the quality of thethesis were to limit itself to the chapters that were considered most relevant toimprove. The analysis revealed a number of points that should be improved, partlyinto the routines when writing the construction specification and when ether sampletext or suggestions should be changed and complemented.

An energy study has been performed on two blocks in an area called Gävle Strand. The buildings are owned by a tenant-owner?s association called brf Carolina and were built by the company Skanska 2008. The builder as well as brf Carolina are pussled by the fact that electricity use is higher than expected while heating is less. Skanska is also very interested in finding out how much heat recovery from stale exhaust air through a geo-thermal heat pump is contributing to the general heating requirement and energy balance in four out of the ten buildings located on the properties.To find possible answers to the higher electricity use a literature survey on user behaviour was conducted.

AbstractTrendanalys av rapporterade störningar vid de svenskakärnkraftverkenAnalysis of trends in reported safety-related events atSwedish nuclear power plantsSafdar KargarThis degree project was conducted at the Swedish Radiation Safety Authority (SSM)as part of the bachelors program in Nuclear Engineering at Uppsala University duringthe spring of 2011.The Swedish Radiation Safety Authority (SSM) has developed a Windows baseddatabase called ?ASKEN? during later years. In this database more than 12 000 eventreports are stored sorted in three categories, category 1, 2 and 3. The databasecontains events from the start of Oskarshamn 1 in 1972 till present time.All nuclear power plants in Sweden are obliged to report any deficiency in theirbarriers and/or the defense in depth in obedience to SSMFS 2008:1.When a failure is detected or there is reasonable suspicion of a deficiency, the eventreport should be classified as a deficiency of category -1, 2 or 3 [1].The event reports are logged and archived in the register of SSM. The SSM task forceAnalys av Störningar på elproducerande Kärnkraftverk (the ASK-group), evaluates allincoming event reports and categorizes them according to established criteria.The aim of the project is to study and analyze the event reports in the database andidentity interesting observations and trends which should be investigated morethoroughly by deeper analysis to establish any positive or negative trends of reportedevents. .

The high level of energy consumption that the industrialised countries have reached and thepollution that this brings has long been a cause for analysis and debate, development and usageof so called renewable energy sources is therefore more important than ever. The energy in theelectromagnetic radiation from the sun is an interesting alternative. One way of harvesting thisenergy is by using solar cells, devices that generate DC current when exposed to electromagneticradiation.The goal of this master?s thesis was to design a solar powered power supply to Syntronic AB?sMidrange platform. The envisioned application is a stand-alone distributed embedded system,for example a node-based temperature monitoring system.

An energy study has been performed on two blocks in an area called Gävle Strand. The buildings are owned by a tenant-owner?s association called brf Carolina and were built by the company Skanska 2008. The builder as well as brf Carolina are pussled by the fact that electricity use is higher than expected while heating is less. Skanska is also very interested in finding out how much heat recovery from stale exhaust air through a geo-thermal heat pump is contributing to the general heating requirement and energy balance in four out of the ten buildings located on the properties.To find possible answers to the higher electricity use a literature survey on user behaviour was conducted.

AbstractTrendanalys av rapporterade störningar vid de svenskakärnkraftverkenAnalysis of trends in reported safety-related events atSwedish nuclear power plantsSafdar KargarThis degree project was conducted at the Swedish Radiation Safety Authority (SSM)as part of the bachelors program in Nuclear Engineering at Uppsala University duringthe spring of 2011.The Swedish Radiation Safety Authority (SSM) has developed a Windows baseddatabase called ?ASKEN? during later years. In this database more than 12 000 eventreports are stored sorted in three categories, category 1, 2 and 3. The databasecontains events from the start of Oskarshamn 1 in 1972 till present time.All nuclear power plants in Sweden are obliged to report any deficiency in theirbarriers and/or the defense in depth in obedience to SSMFS 2008:1.When a failure is detected or there is reasonable suspicion of a deficiency, the eventreport should be classified as a deficiency of category -1, 2 or 3 [1].The event reports are logged and archived in the register of SSM. The SSM task forceAnalys av Störningar på elproducerande Kärnkraftverk (the ASK-group), evaluates allincoming event reports and categorizes them according to established criteria.The aim of the project is to study and analyze the event reports in the database andidentity interesting observations and trends which should be investigated morethoroughly by deeper analysis to establish any positive or negative trends of reportedevents. .